• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.2
• /
• pp.88-96
• /
• 2002

The present study was conducted to estimate the effect on fouling reduction in tubes of the condenser. It shows in detail how to calculate the fouling factor from the experimental results of refrigeration systems with or without the automatic cleaning system using sponge balls and to predict the variation of the factor with time. It also represents how to calculate the temperature and pressure decrease of the refrigerant vapor in the condenser and the load decrease of the compressor in the refrigeration system by fouling reduction.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.136-140
• /
• 1998

This work demonstrates a method for modeling of electrical conductivity in high-temperature proton-conducting oxides. Total conductivity was calculated assuming that it comprises partial conductivities contributed by protons, oxygen ions and electron holes. From the polt $\sigma_{tot}$ vs. $po_2\;{1/4}$ in wet atmosphere, thermodynamic and kinetic parameters were obtained representing transport properties such as concentration and mobility of the charge-carrying defects. The formulas for the calculation of partial conduction were derived based on the defect structure of HTPCs. Illustrative calculation were made for $SrCe_{0.95}Yb_{0.05}O_{2.975}$ system.

• Journal of Navigation and Port Research
• /
• v.27 no.6
• /
• pp.669-675
• /
• 2003

Using a SQUID magnetometer, the diamagnetic susceptibility of NaCl aqueous solution was measured with high accuracy in a magnetic field of up to 6 Tat 25$\pm0.05^{\circ}C$. The NaCl concentrations adopted in this experiment were 0 (water), 7.5, 15, 23, 26.2, 26.6 and 100% (crystal) with the concentration error of $\pm$0.04%. Experimental data was compared with the calculated value of susceptibility derived from dependence of the vapor pressure on NaCl concentration As a result, our measured value was almost in accordance with the calculated value. It was found that the diamagnetic susceptibility shows a decrease of approximately 10% within the saturated concentration (26.2%) and that the susceptibility is one of the effective cause for the concentration dependence in the gas-liquid interface deformation of the NaCl solution.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.347-350
• /
• 2001

A typical Mold method is to form a gate electrode, a gate oxide, and emitter tip after fabrication of mold shape using wet-etching of Si substrate. In this study, however, new Mold method using a side wall space structure is used in order to make sharper emitter tip with a gate electrode. Using LPCVD(low pressure chemical vapor deposition), a gate oxide and electrode layer are formed on a Si substrate, and then BPSG(Boro phospher silicate glass) thin film is deposited. After, the BPSG thin film is flowed into a mold as high temperature in order to form a sharp mold structure. Next TiN thin film is deposited as a emitter tip substance. The unfinished device with a glass substrate is bonded by anodic bonding techniques to transfer the emitters to a glass substrate, and Si substrate is etched using KOH-deionized water solution. Finally, we made sharp field emitter array with gate electrode on the glass substrate.

• Journal of the Korean Ceramic Society
• /
• v.28 no.7
• /
• pp.517-524
• /
• 1991

The CVD process of BPSG (BoroPhosphoSilicate Glass) and its thin film properties were studied. B2H6, PH3, SiH4 and O2 gases were reacted in a AP (Atmospheric Pressure) CVD system in the temperature range of 300℃ and 460℃. The interaction of B2H6 and PH3 was studied from the deposition rate and dopant incorporation change point of view. The dependency of BPSG step coverage on the temperature was changed with different O2/(B2H6+PH3+SiH4) ratio. Finally, the boundary which distinguishes the stable BPSG's from the ones that react with Di (Deionized) water or cleaning chemicals such as H2SO4, HCl, H2O2, NH4OH etc could be defined.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1043-1050
• /
• 2006

An experimental investigation was performed to study flow boiling heat transfer of deionized water in a microchannel. Measurement and evaluation of boiling heat transfer coefficients were carried out using a single horizontal rectangular microchannel having a hydraulic diameter of $100{\mu}m$. Tests were performed for mass fluxes of 90, 169 and 267 $kg/m^2$s and heat fluxes of 200-700 $kW/m^2$. Test results showed that the measured boiling heat transfer coefficients had no dependence on mass flux and vapor quality. Most macro-channel correlations of boiling heat transfer coefficient did not provide reliable predictions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.8
• /
• pp.1195-1202
• /
• 2004

In this paper an experimental study was investigated for two-phase flow distribution in compact heat exchanger header. A test section was consisted of the horizontal bottom dividing header($\phi$: 5 mm, L: 80 mm) and 10 upward circular mini channels ($\phi$: 1.5 mm, L: 850 mm) using an acrylic tube. Three different types of tube intrusion depth were tested for the mass flux and inlet mass quality ranges of 50 - 200 kg/$m^2$s and 0.1 - 0.3, respectively. Air and water were used as the test fluids. The distribution of vapor and liquid is obtained by measurement of the total mass flow rate and the calculation of the quality. Two-phase flow pattern was observed, and pressure drop of each channel was measured. By adjusting the intrusion depth of each channel an uniform liquid flow distribution through the each channel was able to solve the mal-distribution problem.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.188-188
• /
• 2012

ZnO particles with a size range of 50-150 nm were coated with polydimethylsiloxane (PDMS) with a thin film thickness of 3-4 nm using a simple ambient-pressure chemical vapor deposition methods. Surfaces consisting of the PDMS-coated ZnO nanoparticles were found to be superhydrophobic with a water contact angle higher than $160^{\circ}$. The superhydrophobicity was sustained in the presence of UV light. Photocatalytic activity and photocorrosion of ZnO were nearly completely quenched in the presence of PDMS coating. It is suggested that our PDMS-coating can be of potential interest for the application of ZnO in UV protection agents and energy and electronic devices.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.372-376
• /
• 1998

Using calcium-phosphate-powder targets with the Ca/P ratios of 1.0-1.67, hydroxyapatite ($Ca_{10}(PO_4)_6(OH)_2$, HAp) thin films with 4-7㎛ thickness were prepared on titanium metal plates by r.f. magnetron sputtering, followed an annealing at $200^{\circ}C$ for 24 hr under a high water vapor pressure using an autoclave. All the specimens were systematically characterized by XRD, FT-IR, SEM and EDS analyses. The post-annealed films were confirmed to be a nonstoichiometric oxyhydroxyapatite by XRD and FT-IR measurements.

• Journal of the Korean Chemical Society
• /
• v.8 no.4
• /
• pp.179-182
• /
• 1964

The partition function of liquid ammonia was developed by applying the modified significant structure theory of liquid.$^5$ The molar volume, vapor pressure, vaporization entropy were calculated over a wide temperature range. The critical properties for the liquid were also calculated. And surface tensions of the liquid were calculated in a similar manner developed for water by Chang and Pak.$^{10}$ The results show good agreement with experimental observations.