제천 스포츠센터 화재로 29명이 사망하고 40명이 부상을 입었다. 이 논문에서는 스포츠센터 화재 사례에 대해 다수 사상자가 발생한 요인을 분석하기 위해 저자의 화재조사 결과를 토대로 건물과 설비의 구조적인 요인을 분석하고 있다. 건물과 설비의 구조적인 요인은 필로티 구조의 주차장, 필로티 주차장과 로비 사이 방화구획 미비, 필로티 주차장에 스프링클러설비 미설치, 1층 주계단에 방화문 미설치, 옥상에 소화수조 미설치, 2층 주출입구에 벽체 매립형 방화문 설치, EPS실 및 배관 피트 층별 방화구획 부실, 배수배관 연결부의 누수, 화물용 승강기의 승강로와 실내에 면하는 벽체에 합판 설치, 폐쇄형 옥상구조로 개조, 주차장 반자 안쪽 천장에 스티로폼 단열재 부착, 2층 여탕 무창층 강화유리 구조, 드라이비트 외벽으로 분석하였다.
Wafer bonding methods such as fusion and anodic bonding suffer from high temperature treatment, long processing time, and possible damage to the micro-scale sensor or actuators. In the localized bonding process, beating was conducted locally while the whole wafer is maintained at a relatively low temperature. But previous research of localized heating has some problems, such as non-uniform soldering due to non-uniform heating and micro crack formation on the glass capsule by thermal stress effect. To address this non-uniformity problem, a new heater configuration is being proposed. By keeping several points on the heater strip at calculated and constant potential, more uniform heating, hence more reliable wafer bonding could be achieved. The proposed scheme has been successfully demonstrated, and the result shows that it will be very useful in hermetic packaging. Less than 0.2 ㎫ contact Pressure were used for bonding with 150 ㎃ current input for 50${\mu}{\textrm}{m}$ width, 2${\mu}{\textrm}{m}$ height and 8mm $\times$ 8mm, 5mm$\times$5mm, 3mm $\times$ 3mm sized phosphorus-doped poly-silicon micro heater. The temperature can be raised at the bonding region to 80$0^{\circ}C$, and it was enough to achieve a strong and reliable bonding in 3minutes. The IR camera test results show improved uniformity in heat distribution compared with conventional micro heaters. For gross leak check, IPA (Isopropanol Alcohol) was used. Since IPA has better wetability than water, it can easily penetrate small openings, and is more suitable for gross leak check. The pass ratio of bonded dies was 70%, for conventional localized heating, and 85% for newly developed FP scheme. The bonding strength was more than 30㎫ for FP scheme packaging, which shows that FP scheme can be a good candidate for micro scale hermetic packaging.
Instability of a thin film attached to a compliant substrate often leads to emergence of exquisite wrinkle patterns with length scales that depend on the system geometry and applied stresses. However, the patterns that are created using the current techniques in polymer surface engineering, generally have low aspect ratio of undulation amplitude to wavelength, thus, limiting their application. Here, we present a novel and effective method that enables us to create wrinkles with a desired wavelength and high aspect ratio of amplitude over wavelength as large as to 2.5:1. First, we create buckle patterns with high aspect ratio of amplitude to wavelength by deposition of an amorphous carbon film on a surface of a soft polymer poly(dimethylsiloxane) (PDMS). Amorphous carbon films are used as a protective layer in structural systems and biomedical components, due to their low friction coefficient, strong wear resistance against, and high elastic modulus and hardness. The deposited carbon layer is generally under high residual compressive stresses (~1 GPa), making it susceptible to buckle delamination on a hard substrate (e.g. silicon or glass) and to wrinkle on a flexible or soft substrate. Then, we employ glancing angle deposition (GLAD) for deposition of a high aspect ratio patterns with amorphous carbon coating on a PDMS surface. Using this method, pattern amplitudes of several nm to submicron size can be achieved by varying the carbon deposition time, allowing us to harness patterned polymers substrates for variety of application. Specifically, we demonstrate a potential application of the high aspect wrinkles for changing the surface structures with low surface energy materials of amorphous carbon coatings, increasing the water wettability.
일반적으로 초친수 박막들은 물의 퍼짐 현상이 발생하여 빠른 건조와 함께 표면에 붙은 이물질 제거와 공기 중의 미세먼지를 흡착을 하지 않음으로써 표면에 워터스폿(water spot, 물자국)이 생기지 않고 다시 깨끗해지는 자가세정 능력을 가져 유리 및 건축자재의 표면처리 용도로써 많이 사용하고 있다. 이러한 초친수 박막을 제조하는 방법으로는 sol-gel법, 진공 증착법, 화학 기상 증착법, 스퍼터링법 등을 이용한다. 이중 스퍼터링법은 높은 증착속도를 얻을 수 있으며, 비교적 낮은 진공도에서 박막제작을 할 수 있다는 장점을 가진다. 본 실험은 RF-magnetron sputtering법을 이용하여 화학적으로 매우 안정하고 높은 투과율을 가지며 기계적 표면 경도가 우수하여 코팅용 박막으로 널리 이용되고 있는 $TiO_2$와 $SiO_2$를 Single Layer와 Double Layer인 $TiO_2/SiO_2$/Glass박막을 제작하여 초친수 특성을 분석하였다. 광학적 특성을 알아보기 위해 UV-vis spectrophotometer장비를 사용하여 측정한 결과 가시광 영역에서 80% 이상의 높은 투과율을 나타내었다. 이는 모든 박막들의 광학적 특성이 우수하여 높은 광학적 특성을 요구하는 분야에 널리 사용 될 수 있다 것이라는 것을 확인 할 수 있었다. 또한 박막의 표면을 확인하기 위해 AFM을 측정한 결과 모든 박막들은 고른 거칠기를 나타내고 있다는 것을 볼 수 있었다. 이것으로 볼때 초친수 역시 초발수 박막의 표면과 마찬가지로 일정한 패턴을 가져야 하는 것을 확인 할 수 있었다. 박막이 초친수성을 띄기 위해 가장 중요시되는 조건인 접촉각이 5도 이하인 조건을 확인을 위해 Contact Angle을 이용하여 접촉각을 측정해 본 결과 박막들은 초친수성의 조건인 5도 보다 더욱 낮은 접촉각의 측정결과를 나타내었다. 위 실험결과를 볼 때 $TiO_2$와 $SiO_2$를 기반으로 단층 혹은 다층으로 박막을 제작하면 더욱 좋은 초친수 특성을 가져 사회적으로 여러 분야에 사용 가능 할 것이라 사료된다.
Background: The objective of this study was to make colloidal dispersions of the active compounds of radix of Angelica gigas Nakai that could be charaterized as nano-composites using hot melt extrusion (HME). Food grade hydrophilic polymer matrices were used to disperse these compound in aqueous media. Methods and Results: Extrudate solid formulations (ESFs) mediated by various HPMCs (hydroxypropyl methylcelluloses) and Na-Alg polymers made from ultrafine powder of the radix of Angelica gigas Nakai were developed through a physical crosslink method (HME) using an ionization agent (treatment with acetic acid) and different food grade polymers [HPMCs, such as HP55, CN40H, AN6 and sodium alignate (Na-Alg)]. X-ray powder diffraction (XRD) analysis confirmed the amorphization of crystal compounds in the HP55-mediated extrudate solid formulation (HP55-ESF). Differential scanning calorimetry (DSC) analysis indicated a lower enthalpy (${\Delta}H=10.62J/g$) of glass transition temperature (Tg) in the HP55-ESF than in the other formulations. Infrared fourier transform spectroscopy (FT-IR) revealed that new functional groups were produced in the HP55-ESF. The content of phenolic compounds, flavonoid (including decursin and decursinol angelate) content, and antioxidant activity increased by 5, 10, and 2 times in the HP55-ESF, respectively. The production of water soluble (61.5%) nano-sized (323 nm) particles was achieved in the HP55-ESF. Conclusions: Nano-composites were developed herein utilizing melt-extruded solid dispersion technology, including food grade polymer enhanced nano dispersion (< 500 nm) of active compounds from the radix of Angelica gigas Nakai with enhanced solubility and bioavailability. These nano-composites of the radix of Angelica gigas Nakai can be developed and marketed as products with high therapeutic performance.
최근 차세대 디스플레이인 flexible 하고 transparent 한 디스플레이 개발이 진행 중 이며, 이러한 디스플레이가 개발 되기 위해 백 플레인으로 사용되는 Thin Film Transistor (TFT) 또한 차세대 디스플레이 못지 않게 연구가 진행 되고 있다. 기존의 무기물을 기반으로 하고 Rigid한 TFT는 현재 많은 곳에 적용이 되어 사람들이 사용 하고 있다. 하지만 이미 시장은 포화상태이며 차세대 디스플레이 컨셉인 flexible 하고 투명한 것과 맞지 않는다. 그래서 유연하며 투명한 특성을 가진 TFT에 대한 연구가 활발히 진행 되고 있으며 많은 성과를 이루었다. 이러한 소자를 이용하여 훗날 Electronic-skin(e-skin)이라 부르는 전자 피부를 활용하여 실시간 모니터링 할 수 있는 헬스 케어 분야 등에 활용 가치 또한 높다. 현재 유연하며 투명한 기판 및 물질 개발에 많은 연구 개발이 진행 되고 있다. 하지만 유연한 기판을 사용하여 TFT를 제작한 후 stress나 bending에 대한 내구성과 안정성, 신뢰성 등이 무기물을 기반으로 한 TFT에 비해 좋지 않은 실정이다. 따라서 유연하며 투명한 기판을 사용한 TFT에 대한 안정성, 신뢰성 등을 확보하여야 한다. 본 연구 에서는 유연한 기판을 사용하여 TFT를 제작 한 후, TFT특성과 안정성을 확보하는 것을 목표로 실험을 진행하였다. 우리는 Mo전극과 Parylene 기판을 사용하여 유연한 TFT소자를 탑 게이트 구조로 제작 하였고 Rigid한 Glass기판 위에 Floating Process를 진행하기 위해 PVA층을 코팅 후 그 위에 Parylene을 CVD로 증착 하고 IGZO를 Sputter를 사용해 증착했다. Parylene은 DI Water 70도에서 Floating 공정을 통해 Rigid 기판에서 탈착 시켰다. 유연한 기판 위에 TFT를 제작 후 bending에 대한 특성 변화 및 안정성에 대한 측정을 실시하였다. Bending에 대한 특성 변화는 우수한 결과가 나왔지만 안정성 측정 중 Negative Bias Stress(NBS) 상에서 비정상적인 On Current Drop 현상이 발생 되었다. Parylene과 Channel층 사이 interface roughness로 인해 charge trap이 되고 이로 인해 On Current Drop 이라는 현상으로 나타났다. 그래서 우리는 Parylene 기판과 Channel 층간의 surface roughness를 개선하기 위한 방법으로 UV Treatment를 사용하였고 시간을 다르게 하여 surface 개선을 진행했다. Treatment 시간을 증가 시킴에 따라 Surface roughness가 많이 좋아 졌으며, Surface를 개선하고자 비정상적인 On Current Drop 현상이 없어졌으며 위 실험으로 Polymer의 surface roughness에 따라 TFT에 대한 안정성에 대한 신뢰성이 확보 될 수 있는 것을 확인 하였다.
본 논문에서는 반응속도론적 인광 분석기(Kinetic Phosphorescence Analyzer, KPA)를 이 용하여 환경 시료 중의 우라늄 동위원소 분석에 대한 연구를 기술하였다. 극초단파 산분해 기술을 이용하여 토양 및 유리 재질 시료로부터 우라늄 성분을 추출한 후, UTEVA 수지를 통해서 우라늄 동위원소를 순수하게 분리하였고 KPA로 우라늄 농도를 정량하였다. 우라늄 표준용액을 사용하여 KPA를 이용한 우라늄 측정법에 대한 선형성 및 재현성 실험을 수행하였다. 우라늄 표준용액, 지하수 및 인증 표준시료에 대해 KPA를 사용하여 우라늄 농도를 측정하여 KPA를 이용한 우라늄 분석법에 대한 신뢰도를 검증하였다.
콘크리트용 혼화재료로 고로슬래그미분말은 경제적, 환경적 이점뿐만 아니라, 고강도, 내해수성, 내화학성과 같은 성능개선의 효과도 있다. 고로슬래그미분말이 콘크리트용 재료로서 아주 유용한 자원임에도 불구하고, 초기 강도의 저하로 인한 거푸집의 해체 및 순환의 문제로 공사기간이 지연되어 공사비의 증가 등의 단점이 있다. 따라서 본 연구에서는 고로슬래그미분말 혼합 모르타르의 초기 강도의 증진을 위하여, 다양한 알칼리 자극제를 혼합 사용하여, 모르타르의 유동성 및 압축강도 특성을 평가하였다. 또한 알칼리 자극제의 혼합에 따른 수화 반응 성상을 알아보기 위하여, XRD 분석, 미소수화열 및 $Ca(OH)_2$를 정량하였다. 실험결과 유동성과 응결시간에 대한 단점을 고로슬래그미분말로 보완하고, 적당한 알칼리 자극제의 선택과 첨가량을 조절하여 사용한다면, 고로슬래그미분말을 콘크리트에 사용하여도 초기 강도 저하 없이 사용가능할 것으로 판단된다.
Korean government plans to establish large-scale horticulture facility complexes using reclaimed land in order to improve the national competitiveness of agriculture at the government level. One of the most significant problems arising from the establishment of those large-scale horticulture facilities is that these facilities still largely depend on a fossil fuel and they require 24 h a day heating during the winter season in order to provide the necessary breeding conditions for greenhouse crops. These facilities show large energy consumption due to the use of coverings with large heat transmission coefficients such as vinyl and glass during heating in the winter season. This study investigated the applicability of waste heat from power plant for large-scale horticulture facilities by evaluating the waste heat water temperature, heat loss and energy saving performance as a function of distance between power plant and greenhouse. As a result, utilizing power plant waste heat can reduce the energy consumption by around 85% compared to the conventional gas boiler, regardless of the distance between power plant and greenhouse.
Sagsoz, Omer;Demirci, Tevfik;Demirci, Gamze;Sagsoz, Nurdan Polat;Yildiz, Mehmet
The Journal of Advanced Prosthodontics
/
제8권6호
/
pp.417-422
/
2016
PURPOSE. The purposes of this study were to evaluate the staining resistance of CAD/CAM resin-ceramics polished with different techniques and to determine the effectiveness of the polishing techniques on resin-ceramics, comparing it with that of a glazed glass-ceramic. MATERIALS AND METHODS. Four different CAD/CAM ceramics (feldspathic ceramic: C-CEREC Blocs, (SIRONA) and three resin-ceramics: L-Lava Ultimate, (3M ESPE), E-Enamic, (VITA) and CS-CeraSmart, (GC)) and one light cure composite resin: ME-Clearfil Majesty Esthetic (Kuraray) were used. Only C samples were glazed (gl). Other restorations were divided into four groups according to the polishing technique: nonpolished control group (c), a group polished with light cure liquid polish (Biscover LV BISCO) (bb), a group polished with ceramic polishing kit (Diapol, EVE) (cd), and a group polished with composite polishing kit (Clearfil Twist Dia, Kuraray) (kc). Glazed C samples and the polished samples were further divided into four subgroups and immersed into different solutions: distilled water, tea, coffee, and fermented black carrot juice. Eight samples ($8{\times}8{\times}1mm$) were prepared for each subgroup. According to CIELab system, four color measurements were made: before immersion, immersion after 1 day, after 1 week, and after 1 month. Data were analyzed with repeated measures of ANOVA (${\alpha}=.05$). RESULTS. The highest staining resistance was found in gl samples. There was no difference among gl, kc and cd (P>.05). Staining resistance of gl was significantly higher than that of bb (P<.05). Staining resistances of E and CS were significantly higher than those of L and ME (P<.05). CONCLUSION. Ceramic and composite polishing kits can be used for resin ceramics as a counterpart of glazing procedure used for full ceramic materials. Liquid polish has limited indications for resin ceramics.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.