• 한국자동차공학회논문집
• /
• 제6권3호
• /
• pp.63-70
• /
• 1998

According to the stringent exhaust emission regulation control of air fuel ratio is one of the most important issues on gasoline engine. Although many researches have been carried out to identify the fuel transport phenomena in a port fueled gasoline engine, complexity of fuel film behavior in the intake port makes it difficult. The fuel film behavior was investigated recently by using visualization method and these gave us qualitative understanding. In this paper, the quantitative measurement method for the port fuel film is studied by using Fast Response Flame Ionization Detector(FRFID). The mass of fuel film on the port wall was measured by using the methods of fuel injection off, injection on and regression. The Fuel film mass was increased with incresing load at the same engine speed.

• Carbon letters
• /
• 제11권1호
• /
• pp.9-12
• /
• 2010

The synthesis of $C_{60}$@MWCNT was carried out at room temperature (${\sim}25^{\circ}C$) from arc-discharge prepared Multi-wall carbon nanotubes (MWCNTs). They were oxidized and acid treated for tube opening. Then $C_{60}$ molecules were encapsulated into MWCNTs by wetting them with $C_{60}$-toluene solution for several minutes followed by ultrasonification. $C_{60}$@MWCNT was cleaned by pure toluene to remove any excess $C_{60}$. $C_{60}$@MWCNT was characterized by electron microscopy, which showed large scale filling of $C_{60}$ into MWCNTs. It was observed that the mechanism of insertion of $C_{60}$ into MWCNTs may be due to the capillary suction at the opening ends of MWCNTs.

• 대한기계학회논문집B
• /
• 제34권6호
• /
• pp.569-577
• /
• 2010

다상 유체 시스템에 적용할 수 있는 다중스케일 입자 시뮬레이션 기법을 개발하였다. 거시 모델과 미시모델이 만나는 경계영역에서 세가지로 구별되는 기능을 수행하도록 하였다. 먼저, 기상과 액상을 분리하여 연결하기 위해 벽을 설정하였다. 또 경계영역을 근처에서 경계의 위치를 측정하고 이것에 벽의 각도와 위치가 연동하여 접촉각 값을 미시모델에서 거시모델로 전달하게 하였다. 마지막으로, 입자의 삽입과 제거를 통해 경계영역의 질량과 온도를 거시적 조건에 맞추도록 하였다. 이 알고리즘들을 적용한 완전습윤과 부분습윤시스템들은 좋은 결합 결과를 보였다.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.17-22
• /
• 2001

This paper is the first of companion papers, which investigate port-masking effects on lean misfire limit. Port-masking was applied to commercial SOHC 3-valve and DOHC 4-valve engine by inserting masking plates between manifold and port. To induce various conditions of stratification, six types of masking plates were applied. The masking plates were placed in the upstream of injector to prevent wall wetting and two ports were not separated to permit both fuel and air entering through masked port. The results were compared with those by conventional port throttling. The results show that lean misfire limit mainly depends on masking direction, that is, high lean misfire limit is achieved when the port near the spark plug is masked. The mechanism of stratification by masking is different from axial stratification by port throttling. In this case, the rich mixture entering through masked port plays a very important role in the stratification process.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제13권3호
• /
• pp.158-166
• /
• 2005

The present study investigated experimentally and numerically the enhancement of absorption performance due to the waviness of falling film in the vertical absorber tube. The momentum, energy and mass diffusion equations were utilized to find out temperature and concentration profiles at both the interfaces of liquid solution and refrigerant vapor and the wall. Flow visualization was performed to find out the wetting characteristics of the falling film. The maximum heat transfer coefficient was obtained for the wavy flow using spring as an insert device through both numerical and experimental studies. Based on the numerical and experimental results, the maximum absorption rate was found for the wavy-flow using spring as the insert device. The differences between experimental and analytical results ranged from $5.0\;to\;25\%\;when\;Re_j>100$.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2018년도 학술발표회
• /
• pp.277-277
• /
• 2018

Hwang (2015)은 불연속 지형을 지나는 천수 흐름의 해석에서 흐름률을 정확하게 계산하기 위하여 계단에 의한 흐름 저항이 지배적인 계단 전면과 그 영향이 비교적 덜한 계단의 윗부분을 구분하여 접근하는 새로운 기법을 제안하였으며, 모의 결과를 정확해 및 실험실 실험 결과와 비교하였다. 또한 전면 및 후면 계단을 지나는 댐 붕괴 흐름에 대한 실험(Kim et al., 2014)에 적용하여 기존 모형에 비해 새로운 기법에 의한 결과가 보다 우수함을 확인하였다(Hwang, 2016). Kim et al. (2015)은 좌안에 옹벽이 설치된 직선 수로에서 댐 붕괴 흐름에 대한 실험을 수행한 바 있다. 이 연구에서는 Kim et al. (2015)의 실험에 Hwang (2015)의 새로운 기법을 적용하였다. 댐 붕괴에 의한 주 흐름의 진행과 좌안에 직립인 옹벽에서 비교적 표고가 낮은 곳으로 물이 넘나드는 현상이 잘 재현됨을 확인하였다. 이 연구는 국토교통과학기술진흥원의 일부 지원(과제 번호: 14CCTI-C063749 그리고 18AWMP-C140010-01)에 의한 것이다.

• Composites Research
• /
• 제35권2호
• /
• pp.80-85
• /
• 2022

본 연구에서는 항공기 방빙을 위해서 탄소계 소수성 입자인 탄소나노튜브의 코팅 횟수에 따른 테프론-폴리우레탄 탑코트의 나노입자 부착력과 표면 소수성 특성을 평가하기 위하여 실험을 진행하였다. 나노입자 부착력을 측정하기 위해서 인발접착시험을 진행하였고, 표면소수성 특성을 측정하기 위해서 정적접촉각 시험과 거칠기 평가를 진행하였다. 거칠기평가를 통하여 탄소나노튜브가 테프론-폴리우레탄 탑코트에 함침된 정도를 할 수 있었고, USB-현미경을 통하여 테프론-폴리우레탄 탑코트에 탄소나노튜브가 함침 및 분산정도를 확인하였다. 그 결과 코팅횟수가 많을수록 탄소나노튜브가 응집되고 이에 의하여 접착력이 감소한다는 것을 확인하였다. 실험결과 코팅 횟수에 따라 테프론-폴리우레탄의 소수성은 커지고 접착력은 감소하였다. 그로 인해 테프론-폴리우레탄 탑코트 와의 접착력 향상과 최적화된 소수성을 가지는 탄소나노튜브의 코팅횟수를 파악할 수 있었다.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.440-447
• /
• 2020

조적구조는 소규모 건축물에서는 내력벽으로 사용되나 일반적으로 비내력벽으로 간주되어 건축물 골조구조의 내부공간을 구분하는 칸막이벽으로 활용되어진다. 또한 조적공사에서 블록이나 벽돌간의 접착제로 모르타르를 사용하는 습식공법은 양생시간이 필요하여 기후조건에 영향을 받으며, 특히 지진과 같은 횡력에 대해 모르타르의 균열로 벽체의 전도붕괴 등이 발생할 수 있어 매우 취약한 구조이다. 본 연구에서는 이러한 조적구조의 약축방향 전단강성을 보완하고 습식공법의 단점을 개선하는 건식 콘크리트블록 공법을 제안하고 그 구조거동을 규명하고자 한다. 이에 본 연구에서는 콘크리트블록의 재료물성을 살펴보고 수평반복하중에 대한 구조거동실험을 통해 제안된 건식조립 콘크리트블록 벽체의 내진성능을 검증하고자 한다. 본 연구결과에 의하면 첫째로, 콘크리트블록은 KS규준에 C종 블록의 재료성능 이상을 확보하고 있어 습식공법을 대신하는 건식공법에 적용할 수 있을 것이다. 둘째로, 수평반복하중에 대한 벽체의 구조성능은 벽체의 수평길이가 길어짐에 따라 사용된 표준형블록의 증가로 다수의 대각선방향 균열대를 형성하면서 조립블록벽체의 내력이 커짐을 알 수 있다. 끝으로 제안된 건식조립 콘크리트블록 벽체구조는 높이와 길이에 의한 벽체의 형상비가 수평 하중을 받는 구조거동에 주요 영향변수로 판단되어 이를 고려한 내진성능평가가 필요하다.

• International Journal of Automotive Technology
• /
• 제5권4호
• /
• pp.221-238
• /
• 2004

Wall interactions of direct injection spray were investigated using laser-sheet imaging, shadowgraphy, wetted footprint and phase Doppler interferometry techniques. A narrow-cone high-pressure swirl injector is used to inject iso-octane fuel onto a plate, which has three different impact angles inside a pressurized chamber. Heated air and plate conditions were compared with unheated cases. Injection interval was also varied in the heated case to compare dry- and wet- wall impingement behaviors. High-speed macroscopic Mie-scattering images showed that presence of wall and air temperature has only minor effect on the bulk spray structure and penetration speed for the narrow-cone injector tested. The overall bulk motions of the spray plume and its spatial position at a given time are basically unaffected until a few millimeters before impacting the wall. The surface properties of the impact surface, such as the temperature, the presence of a preexisting liquid film also have a small effect on the amount of wetting or the wetted footprint; however, they have strong influence on what occurs just after impact or after a film is formed. The shadowgraph in particular shows that the plate temperature has a significant effect on vapor phase propagation. Generally, 10-20% faster horizontal vapor phase propagation is observed along the wall at elevated temperature condition. For impingement onto a preexisting film, more splash and evaporation were also observed. Contrary to some preconceptions, there is no significant splashing and droplet rebounding from surfaces that are interposed in the path of the DI gasoline spray, especially for the oblique impact angle cases. There also appears to be a dense spray front consists of large sac spray droplets in the oblique impact angle cases. The bulk of the spray is not impacted on the surface, but rather is deflected by it The microscopic details as depicted by phase Doppler measurements show that the outcome of the droplet impaction events can be significantly influenced. Only droplets at the spray front have high enough Weber numbers for wall impact to wet, splash or rebound. Using the sign of vertical velocity, the time-resolved downward droplets and upward droplets are compared. The Weber number of upward moving droplets, which seldom exceeds unity, also decreases as the impact angle decreases, as the droplets tend to impact less and move along the wall in the deflected spray plume.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.171-178
• /
• 2014

From now on, in order to meet more stringer diesel emission standard, diesel vehicle should be equipped with emission after-treatment devices as NOx reduction catalyst and particulate filters. Urea-SCR is being developed as the most efficient method of reducing NOx emissions in the after-treatment devices of diesel engines, and recent studies have begun to mount the urea-SCR device for diesel passenger cars and light duty vehicles. That is because their operational characteristics are quite different from heavy duty vehicles, urea solution injection should be changed with other conditions. Therefore, the number and diameter of the nozzle, injection directions, mounting positions in front of the catalytic converter are important design factors. In this study, major design parameters concerning urea solution injection in front of SCR are optimized by using a CFD analysis and Taguchi method. The computational prediction of internal flow and spray characteristics in front of SCR was carried out by using STAR-CCM+7.06 code that used to evaluate $NH_3$ uniformity index($NH_3$ UI). The design parameters are optimized by using the $L_{16}$ orthogonal array and small-the-better characteristics of the Taguchi method. As a result, the optimal values are confirmed to be valid in 95% confidence and 5% significance level through analysis of variance(ANOVA). The compared maximize $NH_3$ UI and activation time($NH_3$ UI 0.82) are numerically confirmed that the optimal model provides better conversion efficiency of $NH_3$. In addition, we propose a method to minimize wall-wetting around the urea injector in order to prevent injector blocks caused by solid urea loading. Consequently, the thickness reduction of fluid film in front of mixer is numerically confirmed through the mounting mixer and correcting injection direction by using the trial and error method.