• International Journal of Air-Conditioning and Refrigeration
• /
• 제11권4호
• /
• pp.178-187
• /
• 2003

In this study, ventilation flow rate and pressure rise through a tunnel are simulated numerically using computational fluid dynamics (CFD) for various conditions such as roughness height of the surface of tunnel, swirl angle and hub/tip ratio of jet fan, and entrance and exit effects. By using a modified wall function, friction factor can be predicted with respect to the Moody chart within 10% of error for the circular pipe flow and 15% for the present tunnel. For more accurate design, the effect of the swirl angle and hub/tip ratio of jet fan, which is not included in the theoretical equation of pressure rise by jet fan needs to be considered.

• 설비공학논문집
• /
• 제12권3호
• /
• pp.277-283
• /
• 2000

The heat transfer characteristics for air jet vertically impinging on a flat plate which had a set of hybrid rod were investigated experimentally. The rod had a cross section made with a half of circular cross section and that of rectangular and was installed in front of the plate. The heating surface was given constant heat flux value of 1020 W/$m^2^{\circ]C$ and the problem parameters investigated were jet Reynolds number, nozzle-to-plate spacing and the rod size. The local and local average Nusselt number characteristics were found to be dependent on the rod size because the flow was disturbed by installing the rod. Higher convective heat transfer rate occurred in the whole plate as well as in the stagnation region.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.903-910
• /
• 2002

The present study aims to investigate the heat transfer characteristics of a pulsating axisymmetric air jet impinging on a heated wall. An axisymmetric contraction nozzle is used to obtain uniform profiles for the mean velocity and turbulence intensity at the nozzle exit. Measurements of the time averaged temperature on the impingement surface are conducted using a Thermochrornatic Liquid Crystal(TLC) technique for steady and pulsating jets at the jet Reynolds numbers of 20000, 30000 and 40000. Considered are pulsation frequencies of 10 and 20 Hz, corresponding to Strouhal numbers below 0.06 based on nozzle width and jet discharge velocity. In addition, the effect of nozzle-to-plate distances in the range of 2 to 10 on heat transfer characteristics is assessed. The pulsating impinging jet provides more uniform heat transfer coefficient near the impingement region, irrespective of H/D. Based on the measured data, a good correlation as a function of the jet Reynolds and Nusselt numbers is reported. It is also found that an exponent m in the relation of Nu ${\propto}\;Re^m$ depends on both r/D and H/D, by which the impinging jet flows are highly affected.

• 한국추진공학회지
• /
• 제24권5호
• /
• pp.1-12
• /
• 2020

본 논문에서는 재생냉각 연소기에서 냉각제 및 연료로 사용되는 Jet A-1의 열전달 특성에 대해 실험적으로 연구하였다. 냉각채널 가열을 위한 인가 전류, 모사 시편 지름, 시편 후단 압력, Jet A-1 유속을 변화시키며, 시편에서의 벽면 온도 및 시편 전/후단에서의 Jet A-1 온도를 측정하였다. 시편 지름과 유속이 열전달 특성에 중요한 인자임을 알 수 있었으며, 시편의 후단 압력은 열전달 성능에 영향을 주지 않음을 확인할 수 있었다. 열전달 실험결과는 기존 Nu수 경험식들과 비교하였으며, 최종적으로 새로운 Nu수 경험식을 도출하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 봄 학술발표회 논문집
• /
• pp.241-246
• /
• 1998

• 한국항공우주학회지
• /
• 제35권8호
• /
• pp.714-719
• /
• 2007

본 연구에서는 적외선(Infra-Red) 카메라를 이용하여 원형 노즐을 통한 고속 제트 분사 시 수직 충돌 벽면에서 나타나는 정상상태(steady state)의 단열 벽면 온도를 2차원적으로 측정하였다. 출구 노즐 직경으로 표현된, Reynolds 수 187,000에서 노즐-평판간 거리 변화의 영향을 살펴보았으며, 측정된 단열 벽 온도는 회복 계수로 무차원화 하였다. 한편 열전대를 이용하여 측정한 단열 벽면 온도를 적외선 카메라를 이용한 측정 결과와 비교하여 검증하였다.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.357-366
• /
• 1986

본 연구에서는 3공피토우관 및 열선유속계를 사용하여 벽에 평행한 2차원 난류제트의 난류량들을 측정하였고, 스캐니 밸브를 이용하여 벽면아력분포를 측정함 으로써 재순환 영역을 포함한 전체유동장에서의 유동특성을 고찰하였다. 또한 잘 알려진 표준 k-.epsilon. 난류모형 및 유선곡률을 고려한 수정된 k-.epsilon. 난류모형을 이용하여 측정 수치해석을 수행하였다.

• 대한기계학회논문집
• /
• 제8권5호
• /
• pp.442-449
• /
• 1984

본 연구에서는 두 분류가 교우되어 배합이 이루어지는 유동역에서 3차원 방향 에 대하여 평균속도분포, 난류강도분포, 난류전단응력분포, 상관계수의 분포 및 난류 운동에너지와 운동량의 변화 등을 측정 분석하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.324-331
• /
• 2016

The present study focuses on the characteristics of a supersonic jet flowing from a rectangular nozzle exit on a flat plate. Flow visualization techniques using schlieren and kerosene-lampblack tracing are utilized to investigate shock reflection structures and boundary-layer separations over a flat plate. Wall pressure measurements are also carried out to quantitatively analyze the flow structures. All observations are repeated for multiple jet flow boundary conditions by varying the flap length and nozzle pressure ratio. The experimental results show that the jet flow structures over the flat plate are highly three-dimensional with strong bleeding flows from the plate sides, and that they are sensitive to plate length and nozzle pressure ratio. A multi-component force measurement device is also utilized to observe the characteristics of the jet flow thrust vectoring over the plate. The maximum thrust deflection angle of the jet is about $8^{\circ}$, demonstrating the applicability of thrust vector control via a flat plate installed at the nozzle exit.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 추계 학술대회논문집
• /
• pp.219-222
• /
• 2005

Recently, the interest of the engine capacity and environment of the atmosphere is increasing, so the researches for the engine capacity have been conducted for a long time. But the internal environment of an automotive engine is very severe. A piston is exposed to combustion gas of over $2000^{\circ}C$ and strong friction is occurred by high speed motion in the cylinder. The fraction between piston and wall of the cylinder causes the increase of temperature in the engine. The temperature of the engine has an effect on the engine capacity. If the temperature is high, the capacity of the engine is low. So we have to maintain the optimum temperature. To maintain the optimum temperature, the enough flow rate of the engine oil is needed. The oil jet is used to control the flow rate of the engine oil and supply the engine oil to the piston and cylinder. The purpose of this study is to check the mass flow rate of the engine oil and the characteristics of internal flow of the oil jet. Flow pattern of the engine oil is very important because it concludes the loss in the oil jet. This study is the previous research about the oil jet and we will consider the movement of the ball check valve to get more accuracy result.