• 마이크로전자및패키징학회지
• /
• 제16권1호
• /
• pp.27-31
• /
• 2009

본 논문에서는 웨이퍼 레벨 기술을 이용한 CIS용 폴리머 접합 기술을 연구하고 접합 후의 warpage 분석과 개별 패키지의 신뢰성 테스트를 수행하였다. 균일한 접합 높이를 유지하기 위하여 glass 웨이퍼 상에 dam을 형성하고 접합용 폴리머 층을 patterning하여 Si과 glass 웨이퍼의 접합 테스트를 수행하였다. Si 웨이퍼의 접합온도, 접합 압력 그리고 접합 층이 낮을수록 warpage 결과가 감소하였으며 접합시간과 승온 시간이 짧을수록 warpage 결과가 증가하는 것을 확인하였다. 접합 된 웨이퍼를 dicing 하여 각 개별 칩 단위로 TC, HTC, Humidity soak의 신뢰성 테스트를 수행하였으며 warpage 결과가 패키지의 신뢰성 결과에 미치는 영향은 미비한 것으로 확인되었다.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2004년도 춘계학술대회
• /
• pp.50-53
• /
• 2004

본 논문에서는 Si wafer와 Cu사이의 밀착력을 증가시키기 위해 Si wafer전처리 후 plasma와 SAMs처리 방법에 의한 Cu도금의 형성에 관한 방법을 설명하였다. Si wafer를 Piranha solution과 $0.5\%$ HF처리 후 유기박막인 SAMs과 plasma를 이용하는 방법으로 wafer와 Cu층 사이의 밀착력을 증가시켰다. 도금층의 밀착력은 scratch test 로 측정하였으며, AEM을 이용해 시편에 형성된 패턴의 형태를 관찰하고 SEM과 EDS를 이용해 시편의 조직을 관찰하였다. 그 결과 Si wafer를 O2, He, SAMs를 혼합처리 했을 때 밀착성이 가장 우수하였다.

• KSTLE International Journal
• /
• 제5권2호
• /
• pp.37-43
• /
• 2004

Abstract : Nano/micro-scale friction properties were investigated on Si (100) and three self-assembled monolayers (SAMs) (PFOTC, DMDM, DPDM) coated on Si-wafer by chemical vapor deposition technique. Experiments were conducted at ambient temperature(24$pm$1$circ$C) and humidity(45$pm$5%). Friction at nano-scale was measured using Atomic Force Microscopy (AFM) in the range of 0-40nN normal loads. In both Si-wafer and SAMs, friction increased linearly as a function of applied normal load. Results showed that friction was affected by the inherent adhesion in Ssi-wafer, and in the case of SAMs the physical/chemical structures had a major influence. Coefficient of friction of these test samples at the micro-scale was also energies. In order to study the effect of contact area on coefficient of friction at the micro-scale, friction was measured for Si-wafer and DPDM against Soda Lime balls (Duke Scientiffic Corporation) of different radii (0.25 mm, 0.5 mm and 1 mm) at different applied normal loads (1500, 3000 and 4800 mN). Results showed that Si-wafer had higher coefficient of friction than DPDM. Further, unlike that in the case of DPDM, friction in Si-wafer was severely influenced by its wear. SEM evidences showed that solid-solid adhesion was the wear mechanism in Si-wafer.

• 열처리공학회지
• /
• 제26권4호
• /
• pp.178-184
• /
• 2013

The effects of thickness and surface grinding condition on the fracture strength of Si wafer with a thickness under $100{\mu}m$ were investigated. Fracture strength was measured by ball breaker test for about 330 dies (size: $4mm{\times}4mm$) per each wafer. For statistical analysis of the fracture strength, scale factor was determined from Weibull plot. Ball breaker fracture strength was observed to increase with decreasing thickness of silicon die. For the silicon dies of different surface conditions, ball breaker fracture strength was high in the order of polished, ground (#4800), and ground (#320 grit) specimen. Probabilistic fracture strength (i.e., scale factor) increased with decreasing surface roughness of silicon die.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.25-30
• /
• 2011

In this paper, we analyzed the electrical characteristics with Micro-cracks in Photovoltaic module. Micro cracks are increasing the breakage risk over the whole value chine from the wafer to the finished module, because the wafer or cell is exposed to mechanical stress. And The solar cells have to with stand the stress under out door operation in the finished module. Here the mechanical stress is induced by temperature changes and mechanical loads from wind and snow. So, we experimentally analyze the direct impact of micro-cracks on the module power and the consequences after artificial aging. The first step, we made micro-cracks in PV module by mechanical load test according to IEC 61215. Next, PV modules applied the thermal cycling test, because micro-cracks accelerated aging by thermal cycling test, according to IEC61215. Before every test, we checked output and EL image of PV module. As the result of first step, we detected little power loss(0.9%). But after thermal cycling test increased power loss about 3.2%.

• 반도체디스플레이기술학회지
• /
• 제5권3호
• /
• pp.5-10
• /
• 2006

This paper investigates cutting qualities after laser dicing and predicts the problems that can be generated by laser dicing. And through 3 point bending test, die strength is measured and the die strength after laser dicing is compared with the die strength after mechanical sawing. Laser dicing is chiefly considered as an alternative to overcome the defects of mechanical sawing such as chipping on the surface and crack on the back side. Laser micromachining is based on the thermal ablation and evaporation mechanism. As a result of laser dicing experiments, debris on the surface of wafer is observed. To eliminate the debris and protect the surface, an experiment is done using a water soluble coating material and ultrasonic. The consequence is that most of debris is removed. But there are some residues around the cutting line. Unlike mechanical sawing, chipping on the surface and crack on the back side is not observed. The cross section of cutting line by laser dicing is rough as compared with that by mechanical sawing. But micro crack can not be seen. Micro crack reduces die strength. To measure this, 3 point bending test is done. The die strength after laser dicing decreases to a half of the die strength after mechanical sawing. This means that die cracking during package assembly can occur.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.374-375
• /
• 2006

This paper describes anodic bonding characteristics of MCA to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with the same properties were deposited on MCA under optimum RF sputter conditions (Ar 100 %, input power $1\;W/cm^2$). After annealing at $450^{\circ}C$ for 1 hr, the anodic bonding of MCA to Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in $110^{-6}$ Torr vacuum condition. Then, the MCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation and simulation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity being 0.05-0.08 %FS. Moreover, any damages or separation of MCNSi bonded interfaces did not occur during actuation test. Therefore, it is expected that anodic bonding technology of MCNSi-wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1485-1488
• /
• 1997

The capacity of memory chip has increased vert quickly and 64MDRAM becomes main product in semiconductor manufacturing lines consists of many sequential processes, including etching process. although it needs direct sensing of wafer state for the accurae detching, it depends on indirect esnsing and sample test because of the complexity of the plasma etching. This equipment receives the inner light of etch chamber through the viewport and convets it to the voltage inetnsity. In this paper, EDP voltage signal has a new role to detect etching failure. First, we gathered data(EPD sigal, etching time and etchrate) and then analyzed the relationships between the signal variatin and the etch rate using two neural network modeling. These methods enable to predict whether ething state is good or not per wafer. For experiments, it is used High Density Inductive coupled Plasma(HDICP) ethcing equipment. Experiments and results proved to be abled to determine the etching state of wafer on-line and analyze the causes by modeling and EPD signal data.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.482-483
• /
• 2009

In chemical mechanical planarization (CMP) process, the uniformity of stress acting on wafer surface is a key factor for uniform material removal of thin film especially in the oxide CMP. In this paper, we analyze the stress on the contact region between wafer and pad with finite-element analysis (FEA). The setting pressure acting on wafer back side was $500g/cm^2$ and the retainer pressure was changed from 300 to $700g/cm^2$. The polishing test is also done with the same conditions. The material removal rate profiles well-matched with stress distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.310-316
• /
• 2002

In this study, the effects of oxide layer formed on the wear tracks of TiN coated silicon wafer on friction and wear characteristics were investigated. Silicon wafer was used for the substrate of coated disk specimens, which were prepared by depositing TiN coating with $1{\mu}m$ in coating thickness. AISI 52100 steel ball was used for the counterpart. The tests were performed both in air for forming oxide layer on the wear track and in nitrogen to avoid oxidation. This paper reports characterization of the oxide layer effects on friction and wear characteristics using X-ray diffraction (XRD). Auger electron spectroscopy (AES), scanning electron microscopy (SEM) and sliding tests.