• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.295-300
• /
• 2010

Metathetic route for the $MWO_4$ (M=Zn, Co) particles is a simple method of synthesis and a viable alternative method in a short time. $MWO_4$ (M=Zn, Co) particles were synthesized using solid-state metathetic (SSM) method with microwave irradiation. The $MWO_4$ (M=Zn, Co) particles were formed completely at $600^{\circ}C$ for 3 h. The crystallization process, thermal decomposition and morphology of the $MWO_4$(M= Zn, Co) particles were evaluated. The characteristics of the SSM reaction and the formation of a high lattice energy by-product NaCl were discussed.

• Journal of radiological science and technology
• /
• v.13 no.2
• /
• pp.27-30
• /
• 1990

It is an experimental report about object contrast according to the Kinds of screen and obtained results as follows : 1. In the same object radiography, use acquired the difference of the object contrast between LT-II ($CaWO_{4}\;system$) and G4 (Gd system) screens. 2. object contrast more decreased in Gd system screen than $CaWO_{4}$, and object contrast controlled by X-ray tube voltage. 3. The difference of object contrast seen clearly in 80 kVp.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.1
• /
• pp.31-35
• /
• 2010

Coatings of Ni-17 at.%W were electroplated on a steel substrate, and their corrosion behavior was investigated between 600 and $800^{\circ}C$ in an Ar-0.2%$SO_2$ atmosphere. They delayed the corrosion of the steel substrate. They were corroded into an outer NiO-rich layer, and an inner ($WO_3+NiO+NiWO_4$)-mixed oxide layer. Below these oxide layers, a sulfide layer gradually formed.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.111-117
• /
• 2004

The oxidation behavior of 91 WC-9Co hardmetal in weight percentage has been studied in the present work as a part of the development of recycling process. The morphological and compositional changes of the WC-Co hardmetal with oxidation time at 90$0^{\circ}C$ were analyzed by using surface observation and X-ray diffraction. respective]y. As the oxidation time increased, the WC-Co hardmetal was continuously expanded to form porous oxide mixtures of $CoWO_4$ and $WO_3$. The morphology of porous oxide mixture was basically dependent on initial shape of the WC-Co hardmetal. From thermo-gravimetric (TG) analysis, it was found that the oxidation rate was increased with increasing oxidation temperature and oxygen content in the flowing atmospheric gas. The fraction of oxidation versus time curves showed S-curve relationship at a given of oxidation temperature. These oxidation behaviors of the WC-Co hardmetal were discussed in terms of previously proposed kinetic models.

• Journal of the Korean Ceramic Society
• /
• v.23 no.4
• /
• pp.69-77
• /
• 1986

Single crystals of zinc tungstates were grown by the Czochralski method. To obtain the seed crystals various methods were employed including 4 points platinum wirse which dipped the melt and the capillary action from the melt led the 3 differently oriented seeds such as [100], [010] and [001] directions. Optimum growing conditions were observed as neck diameter 2mm rotation speed 50-60 rpm maximum diameter 15mm and pulling rate 0-10 mm/hr. Dendrites covered on the olidified surface in a platinum crucible were turned out to be [001] direction because obviously this crystal has the strong [001] preferential growth habit. The (100) and (010) planes of single crystals showed the slip planes and the (010) plane showed the perfect cleavage surface.

• Journal of Powder Materials
• /
• v.9 no.3
• /
• pp.167-173
• /
• 2002

A new approach to produce nanostructured WC/Co composite powders by a mechanochemical process was made to improve the mechanical properties of advanced hardmetals. Homogeneous spherical W-Co salt powders were made by spray drying of aqueous solution from ammonium metatungstate($(NH_4)_6(H_2W_{12}O_{40})\cdo4H_2O$,AMT) and cobalt nitrate hexahydrate (Co(NO$_3$)$_2$.6$H_2O$). spray dried W-Co salt powders were calcined for 1 hr at $700^{\circ}C$ in atmosphere of air. The oxide powder was mixed with carbon black by ball milling and this mixture was heated with various temperatures and times in $H_2$. The $WO_3/CoWO_4$ composite oxide powders were obtained by calcinations at $700^{\circ}C$. The primary particle size of W/Co composite oxide powders by SEM was 100 nm. The reduction/carburization time decreased with increasing temperatures and carbon additions. The average size of WC particle carburized at $800^{\circ}C$ by TEM was smaller than 50 nm.

• Journal of the Korean Solar Energy Society
• /
• v.23 no.4
• /
• pp.29-35
• /
• 2003

We studied the water splitting into $H_2$ and $O_2$ using two different semiconductor photo catalysts and redox mediator, mimicking the Z-scheme mechanism of the photosynthesis, $H_2$ evolution took place on a Pt-$SrTiO_2$ (Cr-Ta doped) photocatalyst using $I^-$ electron donor under the visible light irradiation. The Pt-$WO_3$ photocatalyst showed an excellent activity of the $O_2$ evolution using $IO_3^-$ electron acceptor under visible light. $H_2$ and $O_2$ gases evolved in the stoichiometric ratio($H_2/O_2$=2) under visible light using a mixture of the Pt-$WO_3$ and Pt-$SrTiO_3$ (Cr-Ta doped) suspended in NaI aqueous solution. We proposed a two-step photo-excitation mechanism using redox mediator under the visible irradiation.

• Journal of Powder Materials
• /
• v.25 no.3
• /
• pp.240-245
• /
• 2018

This study focuses on the fabrication of a WC/Co composite powder from the oxide of WC/Co hardmetal scrap using solid carbon in a hydrogen gas atmosphere for the recycling of WC/Co hardmetal. Mixed powders are manufactured by mechanically milling the oxide powder of WC-13 wt% Co hardmetal scrap and carbon black with varying powder/ball weight ratios. The oxide powder of WC-13 wt% Co hardmetal scrap consists of $WO_3$ and $CoWO_4$. The mixed powder mechanically milled at a lower powder/ball weight ratio (high mechanical milling energy) has a more rapid carbothermal reduction reaction in the formation of WC and Co phases compared with that mechanically milled at a higher powder/ball weight ratio (lower mechanical milling energy). The WC/Co composite powder is fabricated at $900^{\circ}C$ for 6 h from the oxide of WC/Co hardmetal scrap using solid carbon in a hydrogen gas atmosphere. The fabricated WC/Co composite powder has a particle size of approximately $0.25-0.5{\mu}m$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.143.2-143.2
• /
• 2015

백색유기발광소자는 저전력, 높은 명암비 및 빠른 응답속도와 넓은 시야각 등의 장점을 가지고 있어 대형 디스플레이, 모바일 디스플레이, 백색 광원 등에 사용되는 차세대 광원으로써 각광 받고 있고 이를 상용화하기 위해 많은 연구가 진행되고 있다. 하지만 다층 발광층을 가지는 백색유기발광소자는 발광층에 지역이 인가된 전압에 의해 바뀌어 색안정성이 떨어진다는 단점을 가지고 있다. 본 연구에서는 백색유기발광소자의 발광 메커니즘 규명하고 색안정성을 고찰하였다. 이 백색유기발광 소자는 indium-tin-oxide (ITO) 양극전극에 진공 증착 방법을 통해 전하생성층으로 tungsten oxide(WO3)층과 5,6,11,12-tetraphenyltetracene(rubrene)가 도핑된 N,N',-bis-(1-naphthyl)-N,N'-diphenyl1-1'-biphenyl-4,4'-diamine(NPB)층을 사용하여 제작되었다. ITO를 양극으로, NPB를 정공수송층으로, DPVBi를 발광층으로, 4,7-diphenyl-1,10-phenanthroline(BPhen)을 전자수송층으로, WO3와 0, 1, 2, 또는 3 wt% rubrene 도핑된 NPB를 전하생성층으로, Liq를 전자주입지연층으로, Al을 음극 전극으로 각각 사용하였다. 전하생성층으로 사용한 NPB층의 rubrene 도핑농도가 변화하여 백색유기발광소자의 발광 메커니즘을 규명하였다. rubrene 도핑된 NPB층에서 발광하는 노란빛과 발광층에서 발생하는 파란빛에 의해 백색광을 방출, NPB층에 도핑된 rubrene 도핑 농도가 증가할수록 소자의 전류밀도와 밝기가 증가했다.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.60-65
• /
• 1997

The tungsten disulfide $(WS_2)$ solid lubricant was synthesized by two different reaction processes, i.e., the reaction between $CS_2$ gas phase and solid $WO_3$powder, and the vapour phase transport method of tungsten and sulfur in a high vacuum. The chemical and physical characteristics of synthesized $WS_2$powder were analyzed in terms of the average particle size, morphology, crystalline phase etc. in comparison with those of commercial $WS_2$powder. The solid $WO_3$ powder with the average size of 0.2 ${\mu}{\textrm}{m}$ was reacted with $CS_2$gas flowed with$N_2$or 96%$N_2{\times}4%H_2$forming gas for 36 h and 24 h at 90$0^{\circ}C$ respectively. $WS_2$ crystalline phase was then formed through the intermediate phase of .$W_{20}O_{58}$ In the case of vapour phase transport method, the 3.5 wt% iodine was added as a vapour transport reagent into the composition of tungsten and sulfur powders maintaining a constant molar ratio of W:S=1:2.2. The mixture was then heat treated at 85$0^{\circ}C$ for 2 weeks in vacuum. The reaction product obtained showed the average size of 12 ${\mu}{\textrm}{m}$ and the hexagonal plate shape of typical solid lubricant with 2H-$WS_2$crystalline phase.