• 콘크리트학회논문집
• /
• 제16권2호
• /
• pp.261-268
• /
• 2004

RC 구조물이 해양 환경에 노출되거나 염화물 환경에 놓이면 콘크리트 속의 매립철근의 부식이 발생한다. 철근의 부식은 구조물의 내구성을 감소시키게 되며, 이러한 부식은 염화물의 침투로 인해 발생하게 된다. 이에 본 연구에서는 염화물 침투실험을 통하여 콘크리트 물성과 시험법이 염화물 확산에 미치는 영향을 살펴보았다. 실험 결과에 따르면, W/C비와 시험법 모두 콘크리트의 확산계수에 영향을 미치는 것으로 나타났다. W/C비가 증가함에 따라 확산계수도 증가하였으나, 비례하여 증가하지는 않았다. 또한, 시험법에 따른 확산계수의 경우, W/C비의 영향은 잘 반영하나 시험법에 따라 확산계수의 차이가 보인다. 본 연구에서는 W/C비에 따른 확산계수 추정식을 제안하였다.

• KSBB Journal
• /
• 제30권6호
• /
• pp.332-338
• /
• 2015

The objective of this study was designed to determine the possibility of bioethanol production from wasted medium density fiberboard (wMDF). We were investigated the enzymatic saccharification characteristics using the enzyme (Cellic CTec3) after pretreatment with sodium chlorite. According to the component analysis results, the lignin contents before and after the pretreatment of wMDF (milling using sieve size of $1,000{\mu}m$) was significantly reduced from 31.13% to 4.11%. Therefore, delignification ratio of pretreated wMDF was found to be up to about 87-89% depending on the sieve size. And we were tested to compare the saccharification ratio according to the sieve size of wMDF ($1,000{\mu}m$, $200{\mu}m$), but it was no significance depending on the sieve size. When enzyme dosage was 5% based on the substrate concentration, enzymatic saccharification ratio was obtained up to 70% by maintaining at $50^{\circ}C$ for 72 hours. We could made the substrate concentration of pretreated wMDF ($1,000{\mu}m$) up to 12% and then enzymatic saccharification ratio was 76.8%, also contents of glucose and xylose were analyzed to 77,750 and 14,637 mg/L, respectively.

• Archives of Plastic Surgery
• /
• 제42권6호
• /
• pp.753-760
• /
• 2015

Background A number of conditions can alter a person's fingernail configuration. The ratio between fingernail width and length (W/L) is an important aesthetic criterion, and some underlying diseases can alter the size of the fingernail. Fingernail curvature can be altered by systemic disorders or disorders of the fingernail itself. Although the shape and curvature of the fingernail can provide diagnostic clues for various diseases, few studies have precisely characterized normal fingernail configuration. Methods We measured the W/L ratio of the fingernail, transverse fingernail curvature, hand length, hand breadth, and distal interphalangeal joint width in 300 volunteers with healthy fingernails. We also investigated whether age, sex, height, and handedness influenced the fingernail W/L ratio and transverse fingernail curvature. Results In women, fingernail W/L ratios were similar across all five fingers, and were lower than those in men. The highest value of transverse fingernail curvature was found in the thumb, followed by the index, middle, ring, and little fingers. Handedness and aging influenced transverse fingernail curvature, but not the fingernail W/L ratio. Fingernails were flatter on the dominant hand than on the non-dominant hand. The radius of transverse fingernail curvature increased with age, indicating that fingernails tended to flatten with age. Conclusions Our quantitative data on fingernail configuration can be used as a reference range for diagnosing various diseases and deformities of the fingernail, and for performing reconstructive or aesthetic fingernail surgery.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.199-208
• /
• 2021

3D 프린팅 콘크리트의 출력성능 및 부재 강도는 물시멘트비(Water cement ratio, W/C)와 레이어의 프린팅 시간 간격(Printing Time Gap, PTG)에 의하여 큰 영향을 받을 수 있다. 이 연구에서는 W/C와 PTG를 변수로 하여 제작된 프린팅실험체와 몰드 실험체의 표면수분량과 전단부착강도와의 관계를 측정·고찰하였으며, 그 결과, 레이어표면수분량이 전단부착강도에 큰 영향을 주는 것으로 나타났다. 따라서, 3D 프린팅 출력 시 요구되는 레이어 계면 전단부착성능을 확보하기 위해서는 PTG에 따라 적절한 레이어표면수분량이 유지될 수 있도록 유의해야 하며, 레이어표면수분량에 영향을 줄 수 있는 여러 가지 프린팅 환경인자들 대한 후속 연구도 필요할 것으로 판단된다.

• 수산해양기술연구
• /
• 제22권1호
• /
• pp.41-48
• /
• 1986

Ifis recommended that the injection rate should be accurate and reliable in the input data of the performance simulation in diesel engine. Matsuoka Sin improved W. Bosch's injection ratio measurement system. Matsuoka Sin reduced length of the test pipe and set the orifice. However, it was not measured accurately to measure the injection ratio due to reflection wave. In the present thesis, the improved measurement system with combination of the conventional W. Bosch type injection ratio measurement system and Matsuoka Sin type corrected W. Bosch type was practically made. The location of orifice and throttle valve was modified and set one more back pressure valve in order to reduce the effect of reflection wave. The results according to injection condition of multi-hole nozzle are following: 1. Measurement error of injection ratio measurement system in this thesis was $\pm$ 1 %, therefore, its reliability was good. 2. The form of injetion ratio is changed from trapezoidal shape to triangle shape with increase of revolution per minute when injection amount is constant. 3. In the case of constant rpm, the initial injection ratio is almost constant regardless of the amount, meanwhile the injection period becomes longer with increase of the amount. 4. The injection pressure of nozzle isn't largely influenced with injection ratio in the case of constant injection amount and rpm, otherwise the initial injection amount is increased by 3-4% when the injection pressure is low. 5. The injection ratio isn't nearly influenced with back pressure.

• 대한기계학회논문집B
• /
• 제26권12호
• /
• pp.1646-1654
• /
• 2002

A two-phase closed thermosyphon was one of the most effective devices in the removing heat because of its simple structure, thermal diode characteristics, wide operating temperature range and so on. In this study, a two-phase closed thermosyphon(working fluid PFC(C6F14), container copper(inner grooved surface)) was fabricated with a reservoir which can change the fill charge ratio. The experiments were performed in the range of 50~600W heat flow rate and 10~70% fill charge ratio. The results were compared with some correlations that were presented by Rohsenow and Immura et al. in the evaporator, by Nusselt, Gross and Uehara et al. in the condenser and by Cohen and Bayley, Wallis, Kutateladze and Faghri et al. in heat transfer limitation etc.. The heat transfer coefficient at the evaporator increased with the input power. However the effect of the fill charge ratio was nearly negligible. At the condenser, it showed an opposite trend to the evaporator and with increase of the fill charge ratio, showed some enhancement of heat transfer. The heat transport limitation was occurred by the dry-out limitation for small fill charge ratio(10%) and presented about 100W. For the case of large fill charge ratio(Ψ$\geq$40%), it was occurred by the flooding limitation at about 500W.

• 한국전자파학회논문지
• /
• 제18권3호
• /
• pp.341-350
• /
• 2007

본 논문에서는 주파수 조정의 상세 계획에 적용할 목적으로 M/W 중계망의 보호비 유도를 새로이 제안하였으며, 실제 시스템 및 주파수에 대해 동일 및 인접 채널 보호비의 계산 결과를 제시하였다. 가용율 예측에 근거한 제시된 방법은 합성 페이드 마진, 간섭-대-잡음의 비(I/N), 통합 필터 변별도, 시스템 변수로 나타낸 것이다. 계산 결과에 의하면 6.7 GHz, 60 km, 64-QAM, I/N=-6 dB, $BER=10^{-6}$에서 합성 페이드 마진 및 동일 채널 보호비는 각각 25.5 및 50.7 dB을 갖는다. 또한 40 MHz 인접 채널에 대해 통합 필터 변별도 및 인접 채널 보호비는 26.3 및 24.4 dB을 얻는다. 제안된 방법은 M/W 중계망의 보호비 도출에 있어 보다 상세하고 다양한 장치의 변수를 고려한 확장의 용이성 및 실용성 측면에서 이점을 갖는다.

• 대한의용생체공학회:의공학회지
• /
• 제28권2호
• /
• pp.244-249
• /
• 2007

Fluidic conditions for the separation of phases were surveyed in a microfluidic aqueous two-phase extraction system. The infusion ratio between polyethylene glycol (PEG) and dextran solution defines the concentrations of each polymer in micro-channel, which determine the phase-separation. The appropriate ratio between PEG (M.W. 8000, 10%, w/v) and dextran T500 (M.W. 500000, 5%, w/v) in order to perform the separation of phases of both polymers was observed as changing the mixed ratio of both polymers. Based on the fluidic conditions, stable two-phase solutions were obtained within 4% to 8% and 3% to 1% of PEG and dextran, respectively. In addition, the characteristics of the two-phase were discussed. The separation technique studied in the paper can be applied for the implementation of a lab-on-a chip which can detect various biological entities such cells, bacterium, and virus in an integrated manner using built in a biosensor inside the chip.

• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1159-1168
• /
• 1994

We powders were synthesized from W powders in differnet particle sizes by Self-propagating High-temperature Synthesis process (SHS) using a chemical furnace. The effects of the mole ratio of chemical fuel content, pellet thickness and the mole ratio between carbon and tungsten (C/W Ratio) on synthesis were investigated with the tungsten powders have different particle size each other. Compositional and structural characterization of these powders was carried out by scanning electron microscope (SEM0 and x-ray diffractometer. Powder characterization was carried out by the measurement of particle size distribution with laser-particle size analyzer. The amounts of WC obtained by SHS process depend very much on the particle size of tungsten powder and heat contents given in a product, i.e. as the particle size of W powder is smaller, the amounts of WC produced increase. Also the more heat contents is given, the more amounts of WC increase. By optimizing the synthesis conditions, it is possible to fabricate WC powders which have little secondary phases (W2C, C).

• 한국분말재료학회지
• /
• 제1권2호
• /
• pp.159-166
• /
• 1994

The variation of the microstructures and the mechanical properties with varying vacuum hot pressing temperature and pressure was investigated in PyM processed 20 vol%) SiCw/ 2124Al composites. As increasing the vacuum hot pressing temperature, the aspect ratio of whiskers and density of composites increased due to the softening of 2124Al matrix with the increased amount of liquid phase. The tensile strength of composite increased with increasing vacuum hot pressing temperature up to $570^{\circ}C$ and became saturated above $570^{\circ}C$, To attain the high densification of composites above 99%, the vacuum hot pressing pressure was needed to be above 70 MPa. However, the higher vacuum hot pressing pressure above 70 MPa was not effective to increase the tensile strength due to the reduced aspect ratio of SiC whiskers from damage of whiskers during vacuum hot pressing. A phenomenological equation to predict the tensile strength of $SiC_w$/2124AI composite was proposed as a function including two microstructural parameters, i.e. density of composites and aspect ratio of whiskers. The tensile strength of $SiC_w$/2124AI were found more sensitive to the porosity than other P/M materials due to the higher stress concentration and reduced load transfer efficiency by the pores locating at whisker/matrix interfaces.