• Journal of Sericultural and Entomological Science
• /
• v.34 no.2
• /
• pp.52-57
• /
• 1992

Using the new type auxiliary(K-1), dyeing experiment was done at the various dyeing conditions and the effects of auxiliary on the dyeing properties of acid milling dye for the silk fiber were dicussed. The results obtained were as follows; 1. The exhaust rate of acid milling dye was increased according to the auxiliary concentration at dyebath pH 7, But the increasing tendency of exhaust rate was decreased above auxiliary concentration 3% o. w. f.. 2. It was the same tendency of exhaust rate at dyebath pH 5, but the diffusion was more powerful at dyebath pH 7 than pH 5. 3. The decreasing ratio of exhaust rate according to dye concentration increasing was lower at auxiliary addition than auxiliary non-addition. 4. The exhaust rate curve according to increasing dyeing temperature showed the inflection point at auxiliary non-addition, but it was not observed in auxiliary addition. Consequently, it seems to be avoid that the occurrence of uneven dyeing at auxiliary addition.

• Journal of the Korean Applied Science and Technology
• /
• v.7 no.1
• /
• pp.63-70
• /
• 1990

Influence of mixing ratio of blending oil (rice bran oil : RBD palm olein = 1 : 1, 1 : 4 mixture: w/w) and natural tocopherol, citric acid, and sodium polyphosphate on enhancement of oxidation stability of blending oil under the condition of tap water infulx(1 ml/min/200g oil) were compared by AOM test after heating these system at l80$^{\circ}C$. In addition, the effects of tocopherol, and synergist on oxidition stability were also tested with potato chips fried with blending oil(1 : 4 mixture). The result obtained were as followes; 1. The test of RBD palm olein addition of 50% and 80% against rice bran oil on oxidation stability showed that the higher the palm olein contents in blending oil, the higher the oxidation stability. 2. The test of oxidation stability, adding l00ppm, 200ppm and 400ppm of natural tocopherol in two different types of blending oils, A(1 : 1 mixture) and B(1 : 4 mixture), disclosed that blending oil B was more positively effective, and this trend was superior at 200ppm level particularly, Furthermore, oxidation stability was enhanced remarkably upon addition of 100ppm of natural tocopherol, and 50ppm of citric acid together with 50ppm, 100ppm and 200ppm of sodium polyphosphate in general. Especially, 200ppm of sodium polyphosphate addition induced the most synergetic effect on oxidation stability showing as much as 3 times compare to control. 3. The results of oxidation stability obtained by peroxide value on potato chips fried with blending oil (1:4 mixture} added tocopherol, citric acid and sodium polyphosphate and preserved at $60^{\circ}C$ revealed that addition of tocopherol and 50ppm of citric acid together with 200ppm of sodium polyphosphate treatment was the most synergistic coinciding with AOM test results.

• The Korean Journal of Food And Nutrition
• /
• v.33 no.3
• /
• pp.299-308
• /
• 2020

This study investigated the quality characteristics of black soybean sediments to diversify the availability of soybean. The cooking method selected for black soybean sediment preparation was a pressure cooking process without soaking, considering the isoflavone content. The black soybean sediments were prepared by the addition of 0, 10, 30, 50 and 100% (w/w) black soybean. When 0% to 100% black soybean was added to the black soybean sediments, the moisture and crude protein contents increased from 53.17% to 54.41% and from 12.07% to 21.68%, respectively. The total isoflavone content of the black soybean sediments was increased from 2.69 ㎍/g to 696.09 ㎍/g, respectively, by the addition of black soybean. The anthocyanin content of the black soybean sediments ranged from 279.29 ㎍/g to 387.8 ㎍/g by the addition of black soybean. The total polyphenol content and the total flavonoid content of the black soybean sediments range from 1.72 mg/g to 2.00 mg/g and 0.89 mg/g to 0.92 mg/g, respectively, by the addition of black soybean. Given the isoflavones, total polyphenol, and anthocyanin content of the black soybean sediments, it is appropriate that the ratio of added black soybeans is at least 50% after the pressure-cooking process, regardless of soaking.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.12
• /
• pp.1027-1032
• /
• 2002

(Pb$\_$0.4/Ca$\_$0.6/)(Fe$\_$1/2/Nb$\_$1/2/)O$_3$ system was modified by 10 mol% Pb(Zn$\_$1/2/W$\_$1/2/)O$_3$ addition and their sinterability and microwave properties were investigated as a function of the amount of flux (0.975PbO-0.025SnO$_2$). With increasing flux content, single perovskite phase was maintained up to 3 wt% flux addition and further addition led to the presence of Pb-rich second phase which was confirmed by EDS analysis. The apparent densities of PCFN-PZW specimen increased and showed maximum values at 2.5 wt% flux addition for the Ts=1000$^{\circ}C$ and 2.0wt% flux addition for the Ts=1050$^{\circ}C$, respectively. The dielectric constant and Q$.$f values strongly depended on the variation of density and microstructure, where the optimum values of $\varepsilon$$\_$r/ = 91.95, Q$.$f = 5938GHz, TCF = +8.15ppm/$^{\circ}C$ were obtained for the 2.5wt% flux added PCFN-PZW specimen sintered at 1000$^{\circ}C$ for 4h.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.28-29
• /
• 2006

The magnetic properties of a series of both annealed and as-rolled Ni-$W_y$ alloy tapes with compositions y = 0, 1, 3, and 5 at.%, were studied. To compare with Ni-W alloys, the magnetic properties of a series of both annealed and as-rolled $[Ni_{97at.%}W_{3at.%}]_{100-x}Cu_x$ alloy tapes with compositions x = 0, 1, 3, 5 and 7 at.%, were studied, as well. Both the isothermal mass magnetization M(H) of a series of samples, such as both Ni-W and [Ni-W]-Cu alloy tapes, at different fixed temperatures and M(T) in fixed field, were measured using a PPMS-9 (Quantum Design). The degree of ferromagnetism of Ni-$W_y$ alloys have reduced as W-content y increases. Both the saturation magnetization $M_{sat}$ and Curie temperature $T_c$ decrease linearly with W-content y, and both $M_{sat}$ and $T_c$ go to zero at critical concentration of $y_c$ ~ 9.50 at.% W. The effect of Cu addition on both the saturation magnetization $M_sat$ and Curie temperature $T_c$ decrease linearly with Cu-content x in $[Ni_{97at.%}W_{3at.%}]_{100-x}Cu_x$ alloy tapes with compositions x = 0, 1, 3, 5, and 7 at.%. The results confirm that [Ni-W]-Cu alloy tapes can have much reduced ferromagnetism as Cu-content x increases.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.87.1-87.1
• /
• 2011

The residential Fuel Cell system has high efficiency of 85% with transferring natural gas to electrical power and heat, directly and it is a friendly environmental new technology in that $CO_2$ emission can reduce 40% compared with conventional power generator and boiler. The residential fuel cell system consists of two main parts which have electrical and hot storage units. The electrical unit contains a fuel processor, a stack, an inverter, a control unit and balance of plant(BOP), and the cogeneration unit has heat exchanger, hot water tank, and auxiliaries. 5kW class fuel process was developed and tested from 2009, it was evaluated for long-term durability and reliability test including with improvement in optimal operation logic. Stack development was crried out through improvement of design and evaluation protocol. Development of system controller was successfully accomplished through strenuous efforts and original control logic was optimized in 5kW class PEMFC system. In addition, we have been focused on development of system process and assembly technology, which bring about excellent improvement of reliability of system. The 5kW class PEMFC system was operated under dynamic conditions for 1,000 hours and it showed a good performance of total efficiency and durability.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.121-124
• /
• 2007

Stacks of solid oxide fuel cell under 1kW max power were designed on planar type employing anode supported cell and metallic interconnects. The stacks composed of 3-cells, 8-cells, and 16-cells were fabricated by using single cell purchased from Indec, sealant and interconnect prepared at RIST. In performance test of the final 16-cells stacks, OCV was recorded to be 16.7 V. Peak power and power density were 1 kW, 0.77 $W/cm^{2}$ at $820^{\circ}C$, respectively. In addition, the long term degradation rate of the power exhibited 2.25 % in 500 h at $750^{\circ}C$.

• Journal of Powder Materials
• /
• v.4 no.2
• /
• pp.113-121
• /
• 1997

The densification of the compacts of Co+32%Cr+20%W+l.5%C, Co+32%Cr+20%W+3.0%C and Co+32%Cr+20%W+4.5%C sintered under $H_2$ gas or vacuum was investigated. The effect of V and B addition on the densification was also investigated. The densification of these compacts were always incomplete regardless of sintering atmosphere, temperature and time. The amounts of oxygen and carbon in compacts sintered in $H_2$ for 3.6ks at 1523K were 0.105~0.160 mass% and 0.33~0.89 mass%, respectively. And those in vacuum were 0.028~0.032% and 0.957~4.08%, respectively. Relative density(Ds) of Co+29%Cr+17%W+3.0%C compact containing 6%V and Co+32%Cr+20%W+2.97%C compact containing 0.03%B were 99 and 100%, respectively, indicating complete densification by solid phase sintering. Victors hardness of sintered compacts containing 6%V or 0.03%B were 632 and 568, showing 50~60% increase in comparison to those without V or B. These results can be explained in terms of oxidation/reduction of oxides and equilibrium pressure of CO in isolated pore, instead of presence of liquid formation and grain boundary separation from pores due to large grain growth.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.200-205
• /
• 2010

Heat-resistance of W/$Y_2O_3$ as throat insert material was evaluated to develop rocket motor keeping thrust uniformly under condition of high-temperature, high-pressure and long-burn time. Test was conducted with varying burn time, and test results were compared with CIT. Test showed that ablation rate was decreased according as burn time was increased, and that ablation rate of W/$Y_2O_3$ was about 55 % of CIT. Macro/micro structures of throat insert did not show a peculiar phenomenon by increased burn time. In addition, the vacuum heat treatment is effective for the prevention of crack in throat insert.

• Journal of the Korean Applied Science and Technology
• /
• v.15 no.2
• /
• pp.25-32
• /
• 1998

The emulsion stability of W/O emulsion prepared by D phase emulsification during storage and handling is studied by using phase diagrams. The process of D phase emulsification begins with the formation of isotropic surfactant solution, followed by formation of oil-in-surfactant (O/D) gel emulsion by dispersion of octamethylcyclotetrasiloxane(OMCS) in the surfactant solution. Polyols were essential components for this purpose. To understand the function of polyols, the solution behavior of nonionic surfactant/oil/water/polyol systems were investigated by the ternary phase diagrams of polyoxyethylene oleyl ether/OMCS/propylene glycol(PG) aqueous solutions. The addition of PG increased the solubility of oil in the isotropic surfactant phase. D phase emulsification method has been applied to a new type of cosmetics. By using this emulsification technique, O/W emulsion were formed without a need for adjust of HLB. Fine and stable W/O emulsions were prepared by D phase emulsion.