• Transactions on Electrical and Electronic Materials
• /
• v.5 no.1
• /
• pp.15-18
• /
• 2004

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of a-C:H thin film by plasma enhanced chemical vapor deposition (PECVD) system for 30 sec under 30W rf power at a gas pressure of 1.4＊10$\^$-1/ torr. A high pretilt angle of about 5 by ion beam exposure on the a-C:H thin film surface was measured. A good LC alignment by the ion beam alignment method on the a-C:H thin film surface was observed at annealing temperature of 250$^{\circ}C$, and the alignment defect of NLC was observed above annealing temperature of 300$^{\circ}C$. Consequently, the high LC pretilt angle and the good thermal stability of LC alignment by the ion beam alignment method on the a-C:H thin film by PECVD method as working gas at 30W rf bias condition can be achieved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2007.02a
• /
• pp.172-172
• /
• 2007

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1474-1476
• /
• 2005

ZnO:Al(AZO) has been investigated for the photovoltaic cell or TCO(Transparent Conductive Oxide) of the display, because it has good electrical and optical properties. In this study, the ZnO:Al(AZO) thin film prepared on variation of substrate temperature by FTS(Facing Targets Sputtering) system. In case of TCO, because resistivity and roughness values affect the lighting of the OLED, their factors are very important. Therefore, in this paper, the electrical and optical properties of the AZO thin film were investigated with the deposition conditions and its roughness was investigated on variation of the substrate temperature. In results, AZO thin film deposited with the transmittance over 80% and the resistivity was reduced from $1.36{\times}10^{-3}$ [O-cm] to $4{\times}10^{-4}$ [O-cm] with increasing the substrate temperature from R.T to $200[^{\circ}C]$. Especially, we could obtain the resistivity $4{\times}10^{-4}$ [O-cm] of AZO thin film prepared at working pressure 1[mTorr], input current 0.4[A] and substrate temperature $200[^{\circ}C]$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.234-239
• /
• 2007

This paper describes the TiW ohmic contact characteristics under the surface treatment of the polycrystalline 3C-SiC thin film grown on $SiO_2/Si(100)$ wafers by APCVD. The poly 3C-SiC surface was polished by using CMP(chemical mechanical polishing) process and then oxidized by wet-oxidation process, and finally removed SiC oxide layers. A TiW thin film as a metalization process was deposited on the surface treated poly 3C-SiC layer and was annealed through a RTA(rapid thermal annealing) process. TiW/poly 3C-SiC was investigated to get mechanical, physical, and electrical characteristics using SEM, XRD, XPS, AFM, optical microscope, I-V characteristic, and four-point probe, respectively. Contact resistivity of the surface treated 3C-SiC was measured as the lowest $1.2{\times}10^{-5}{\Omega}cm^2$ at $900^{\circ}C$ for 45 sec. Therefore, the surface treatments of poly 3C-SiC are necessary to get better contact resistance for extreme environment MEMS applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.87-88
• /
• 2007

반도체 소자가 초고집적화 되어감에 따라 반도체 공정에서 선폭은 줄어들고 박막은 다층화 되어가고 있다. 이와 같은 제조 공정 하에서는 Si 기판과 금속 박막간의 확산이 커다란 문제로 부각되어 왔다. 특히 Cu는 높은 확산성에 의하여 Si 기판과 접합에서 많은 확산에 의한 문제가 발생하게 되며, 또한 선폭이 줄어듦에 따라 고열이 발생하여 실리콘으로 spiking이 발생하게 된다. 이러한 확산을 방지하기 위하여 이 논문에서는 Tungsten - Carbon - Nitrogen (W-C-N)에 Boron (B)을 첨가하였고, Boron 타겟 power을 조절하여 다양한 조성을 가지는 W-B-C-N 확산방지막을 제작하여 각 조성에 따른 증착률을 조서하였고 $1000^{\circ}C$까지 열처리하여 그 비저항을 측정하여 각 특성을 확인하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.440-448
• /
• 2004

In this paper, to make a solar cell of II-Ⅵ ZnTe compound semiconductor, we studied for the property of the transparent electrode(AZO) and Buffer layer(ZnO), and for reducing the energyband gap of optical absorber layer which are most effective on its efficiency. The ZnTe thin film was used the optical absorber layer of solar cell. Zn and Te were deposited using the co-sputtering method. The thin film was sputtered RF power of Zn/50W and Te/30W, respectively and a substrate temperature of foot under Ar atmosphere of 10mTorr. The energy band gap of the thin film was 1.73ev Then the thin film was annealed at $400^{\circ}C$ for 10sec under a vacuum atmosphere. The energy band gap of 1.67eV was achieved and the film composition ratio of Zn and Te was 32% and 68%. At the best condition, the Solar Cell was manufactured and the efficiency of 6.85% (Voc: 0.69V, Jsc: 21.408㎃/$cm^2$, Fill factor (FF): 0.46) was achieved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.104-107
• /
• 2001

The fabricated La-modified lead titanate (PLT) thin flim without paling treatment was investigated for modulation frequency dependence of pyroelectric properties by the dynamic method. $Pb_{1-x}La_{x}Ti_{1-x/4}O_{3}$ PLT (x=0.1) thin film having 10 mol% La content was deposited on a $Pt/TiO_{x}/SiO_{2}/Si$ substrate by sol-gel method. The PLT(10) thin film exhibits a relatively excellent dielectric property. The pyroelectric coefficient (p) of the PLT(10) thin film is $6.6{\times}10^{-9}C/cm_{2}\cdot K$ without frequency dependence. The figure of merits for the voltage responsivity and specific detectivity are $1.03{\times}10^{-11}C\cdot cm/J$ and $1.46\times 10^{-9}C\cdot cm/J$, respectively. The PLT(10) thin film has voltage responsivity (Rv) of 5.15 V/W at 8 Hz. Noise equivalent power (NEP) and specific detectivity (D*) of the PLT(10) thin film are$9.93{\times}10^{-8}W/Hz^{1/2}$ and $1.81\times 10^{6}cmHz^{1/2}/W$ at the same frequency of 100 Hz, respectively. The results means that PLT thin film having 10 mol % La content is suitable for the sensing materials of pyroelectric IR sensors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.104-107
• /
• 2001

The fabricated La-modified lead titanate (PLT) thin flirt without poling treatment was investigated for modulation frequency dependence of pyroelectric properties by the dynamic method. $Pb_{1-x}La_{x}Ti_{1-x/4}O_3$PLT (x=0.1) thin film having 10 mol% La content was deposited on a Pt/$TiO_{x}$/$SiO_2$/Si substrate by sol-gel method. The PLT(10) thin film exhibits a relatively excellent dielectric property. The pyroelectric coefficient (p) of the PLT(10) thin film is 6.6 x $10^{-9}$C/$\textrm{cm}^2$.K without frequency dependence. The figure of merits for the voltage responsivity and specific detectivity are 1.03${\times}$$10^{-11}$/C.cm/J and 1.46 x $10^{-9}$C.cm/J, respectively. The PLT(10) thin film has voltage responsivity ($R_{V}$) of 5.15 V/W at 8 Hz. Noise equivalent power (NEP) and specific detectivity (D＊) of the PLT(10) thin film are 9.93 x $10^{-8}$W/Hz$^{1/2}$ and 1.81 x $10^{6}$ cmHz$^{1/2}$/W at the same frequency of 100 Hz, respectively. The results means that PLT thin film having 10 mol % La content is suitable for the sensing materials of pyroelectric IR sensors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.248-249
• /
• 2007

The $V_{1.9}W_{0.1}O_5$ thin films deposited on Pt/Ti/$SiO_2$/Si substrates by RF sputtering method exhibited fairly good TCR and dielectric properties. It was found that film crystallinity, dielectric properties, and TCR properties were strongly dependent upon the annealing temperature. The dielectric constants of the $V_{1.9}W_{0.1}O_5$ thin films annealed at $300^{\circ}C$ were 37.7, with a dielectric loss of 2.535, respectively. Also, the TCR values of the $V_{1.9}W_{0.1}O_5$ thin films annealed at $300^{\circ}C$ were about -3.7%/K.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.10
• /
• pp.35-42
• /
• 2002

Modulation frequency dependences of the pyroelectric properties of PLT (P $b_{1-x}$ L $a_{x}$ $Ti_{1-x}$ 4/ $O_3$) thin films with La concentrations of 5, 10 and 15㏖% have been investigated by using the dynamic method. The PLT thin film with 10㏖% of the La concentration (PLT(10) thin film) shows the most excellent pyroelectric properties among the films. For PLT(10) thin film, the pyroelectric coefficient shows the maximum value of 6.6$\times$10$^{-9}$ C/$\textrm{cm}^2$ㆍK without frequency dependence. The figure of merits for the voltage responsivity and specific detectivity are 1.03$\times$10$^{-11}$ Cㆍcm/J and 1.46$\times$10$^{-9}$ Cㆍcm/J, respectively. Voltage responsivity corresponding to the pyroelectric voltage is almost constant at low modulation frequency and decreases in proportional to frequency at high modulation frequency. Voltage responsivity is 5.15 V/W at 8Hz. Noise equivalent power (NEP) and specific detectivity ( $D^{*}$) of the PLT(10) thin film are 9.93$\times$10$^{-8}$ W/H $z^{1}$2/ and 1.81$\times$10$^{6}$ cmH $z^{1}$2/W at the frequency of 100Hz, respectively. The results indicate that PLT(10) thin film is very suitable for pyroelectric IR sensors.s.s.