• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.1
• /
• pp.33-37
• /
• 2000

The 1-3 piezoelectric composite transducer with 75 volume percents PZT was fabricated by the dicing-filling method. The resonance modes of the 1-3 transducer have been studied with electric impedance measurement as a function of frequency. The fundamental frequencies of the planar and thickness mode were observed at 0.95MHz and 1.63MHz respectively, but the lateral mode was not observed. In the thickness mode, the electromechanical coupling coefficient of the 1-3 piezoelectric composite transducer, 0.54, was very closed to that of the single phase PZT(0.52). The pulse-echo response by exciting the 1-3 transducer with an electric pulse was observed from the water/reflector interface, and analyzed bandwidth by the spectrum of the impulse response. The quality factor Q for the 1-3 transducer was observed as 1.5 smaller than that of the single phase(80) and then the 1-3 transducer may be used to the broad band type transducer applications.

• Journal of the Korean Society of Radiology
• /
• v.8 no.1
• /
• pp.19-26
• /
• 2014

This paper suggests techniques to enhance coding time which is a problem in traditional fractal compression and to improve fidelity of reconstructed images by determining fractal coefficient through adaptive selection of block approximation formula. First, to reduce coding time, we construct a linear list of domain blocks of which characteristics is given by their luminance and variance and then we control block searching time according to the first permissible threshold value. Next, when employing three-level block partition, if a range block of minimum partition level cannot find a domain block which has a satisfying approximation error, we choose new approximation coefficients using a non-linear approximation of luminance term. This boosts the fidelity. Our experiment employing the above methods shows enhancement in the coding time more than two times over traditional coding methods and shows improvement in PSNR value by about 1-3dB at the same compression rate.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.1
• /
• pp.31-37
• /
• 2015

Composition-controlled ternary components chalcogenides germanium tin sulfide ($Sn_xGe_{1-x}S$) nanoparticles were synthesized by a novel gas-phase laser photolysis reaction of tetramethyl germanium, tetramethyl tin, and hydrogen sulfide mixture. Subsequent thermal annealing of as-grown amorphous nanoparticles produced the crystalline orthorhombic phase nanoparticles. All these composition-tuned nanoparticles showed excellent cycling performance of the lithium ion battery. The germanium sulfide nanoparticles exhibit a maximum capacity of 1200 mAh/g after 70 cycles. As the tin composition (x) increases, the capacity maintains better at the higher discharge/charge rate. This novel synthesis method of tin germanium sulfide nanoparticles is expected to contribute to expand their applications in high-performance energy conversion systems.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.6
• /
• pp.117-125
• /
• 2007

Recently, a fuel cell with low voltage and high current output characteristics is remarkable for new generation system. It needs both a DC-DC step-up converter and DC-AC inverter to be used in fuel cell generation system. Therefor, this paper, consists of an isolated DC-DC converter to boost the fuel cell voltage 380[VDC] and a PWM inverter with LC filter to convent the DC voltage to single-phase 220[VAC]. Expressly, The fuel cell system which it proposes DC-DC the efficient converter used PWM the phase transient control law and it depended to portion resonance ZVS switching, loss peek voltage and electric current of realization under make schedule, switching frequency anger and the switch reduction. And mind benevolence it sprouted 2 in stop circuit and it added and a direct current voltage and the electric current where the ingredient is reduced in load side ripple stable under make whom it will be able to supply. Besides the efficiency of 92[%]is obtained over the wide output voltage regulation ranges and load variations. Also, under make over together the result leads simulation and test, the propriety confirmation.

• Investigative Magnetic Resonance Imaging
• /
• v.6 no.1
• /
• pp.41-46
• /
• 2002

The Fourier transform arteriography (FTA) exploits the periodic variation of arterial flow velociety of arterial flow velocity in stnchronized with cardiac cycles. This technique is intrinsically unique compared to other modern techniques. This technique separates the arteries from the veins using the pulsatile arterial flow without using the presaturation RF pulses. Therefore, it has less RF deposition and is free from the dark band artifacts that can arise from retrograde flow and curved arteries. Furthermore, it is free from the artifacts induced by eddy currents. However, there are some drawbacks such as a single projection view and the saturation of arteries at the end of an imaging slab. These drawbacks are circumvented by applying recently developed techniques. The fast gradient switching capability of modern MRI systems enabled us to incorporate dual projection views into the conventional FTA sequence without increasing the repetition time. In addition, signals from the distal arteries were enhanced by use of a ramped RF pulse and therefore the distal arteries were less saturated. By use of the FTA sequence with dual projection views and the ramped RF pulse, we acquired the sagittal and coronal projection views of femoral arteriograms simultaneously with more enhanced signals of distal arteries than the conventional FTA.

• Solar Energy
• /
• v.12 no.2
• /
• pp.62-78
• /
• 1992

The solar cells of $ITO_{(n)}/Si_{(p)}$, which are ITO thin films deposited and heated on Si wafer 190[$^{\circ}C$], were fabricated by two source vaccum deposition method, and their electrical properties were investigated. Its maximum output is obtained when the com- position of the thin film consist of indium oxide 91[mole %] and thin oxide 9[mole %]. The cell characteristics can be improved by annealing but are deteriorated at temperature above 600[$^{\circ}C$] for longer than 15[min]. Also, we investigated the spectral response with short circuit current of the cells and found that the increasing of the annealing caused the peak shifted to the long wavelength region. And by experiment of the X-ray diffraction, it is shown to grow the grains of the thin film with increasment of annealing temperature. The test results from the $ITO_{(n)}/Si_{(p)}$ solar cell are as follows. short circuit current : Isc= 31 $[mW/cm^2]$ open circuit voltage : Voc= 460[mV] fill factor : FF=0.71 conversion efficiency : ${\eta}$=11[%]. under the solar energy illumination of $100[mW/cm^2]$.

• Journal of the Korean Society of Radiology
• /
• v.8 no.7
• /
• pp.435-441
• /
• 2014

This paper suggests techniques to enhance coding time which is a problem in traditional fractal compression and to improve fidelity of reconstructed images by determining fractal coefficient through adaptive selection of block approximation formula. First, to reduce coding time, we construct a linear list of domain blocks of which characteristics is given by their luminance and variance and then we control block searching time according to the first permissible threshold value. Next, when employing three-level block partition, if a range block of minimum partition level cannot find a domain block which has a satisfying approximation error, There applied to 24-bpp color image compression and image techniques. The result did not occur a loss in the image quality of the image when using the encoding method, such as almost to the color in the RGB image compression rate and image quality, such as gray-level images and showed good.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.1
• /
• pp.54-61
• /
• 2008

This paper presents a new TIQ based CMOS flash 6-bit ADC to process digital signal in real time. In order to improve the conversion speed of ADC by designing new logic or layout of ADC circuits, a new design method is proposed in encoding logic circuits. The proposed encoding circuits convert analog input into digitally encoded double base number system(DBNS), which uses two bases unlike the normal binary representation scheme. The DBNS adopts binary and ternary radix to enhance digital arithmetic processing capability. In the DBNS, the addition and multiplication can be processed with just shift operations only. Finding near canonical representation is the most important work in general DBNS. But the main disadvantage of DBNS representation in ADC is the fan-in problem. Thus, an equal distribution algorithm is developed to solve the fan-in problem after assignment the prime numbers first. The conversion speed of simulation result was 1.6 GSPS, at 1.8V power with the Magna $0.18{\mu}m$ CMOS process, and the maximum power consumption was 38.71mW.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.4
• /
• pp.334-341
• /
• 2003

When the pressure tubes(f are in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature difference between inner and outer wall of W results in a thermal diffusion of hydrogen (deuterium) and hydride blisters are formed on the outer surface of PT. Because the hydride blisters and zirconium matrix are acoustically continuous, it is not easy to distinguish the blisters from the matrix with conventional ultrasonic method. An ultrasonic velocity ratio method was developed to detect small hydride blisters on the zirconium pressure tube. Hydride blisters were grown in the PT specimen using a steady state thermal diffusion device. The flight times of longitudinal echo and reflected shear echo from the outer surface were measured accurately. The velocity ratio of the longitudinal wave to the shear wave was calculated and displayed using contour plot. Compared to the conventional flight time method of longitudinal wave, the velocity ratio method shows superior sensitivity to detect smaller blisters as well as better images for the blister shapes. Detectable limit of the outer shape of the hydride blisters was conservatively estimated as $500{\mu}m$, with the same specifications of ultrasonic transducer used in the actual PHWR pressure tube inspection.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.8B
• /
• pp.1119-1128
• /
• 2001

본 논문에서는 이차원(2-D) 이산 웨이블릿 면환(Discrete Wavelet Transform, DWT)을 이용한 연상압축기를 FPGA 칩에서 실시간으로 동작 가능하도록 하는 효율적인 메모리 스케줄링 방법(E$^2$M$^2$)을 제안하였다. S/W적으로 위의 메모리 사상 방법을 검증한 후, 실제로 상용화된 SFRAM을 선정하여 메모리 제어기를 구현하였다. 본 논문에서는 Mallet-tree를 이용한 2-D DWT 영상압축 칩을 구현할 경우를 가정하였다. 이 알고리즘은 연산 과정에서 많은 데이터를 정장하여야 하는데, FPGA는 많은 데이터를 저장할 수 있는 메모리가 내장되어 있지 않으므로 외부 메모리를 사용하여야 한다. 외부메모리는 열(row)에 대해서만 연속(burst) 읽기, 쓰기 동작이 가능하기 때문에 Mallet-tree 알고리즘의 데이터 입출력을 그대로 적용할 경우 실시간 동작을 수행하는 DWT 압축 칩을 구현할 수 없다. 본 논문에서는 데이터 쓰기를 수행할 경우에는 메모리 셀(cell)의 수직 방향을 저장시키고 읽기를 수행할 때는 수평으로 데이터의 연속 읽기를 수행함으로써 필터가 항상 수평 방향에 위치하게 하는 방법을 제안하였다. 입방법을 C-언어로 DWT 커넬(Kernel)과 메모리의 에뮬레이터(emulator)를 구현하여 실험한 결과, Mallat-tree 이론을 그대로 적용시켰을 때와 동일한 필터링을 수행할 수 있음을 검증하였다. 또한, 상용화된 SDRAM의 메모리 제어기를 H/W로 구현하여 시뮬레이션 함으로써 본 논문에서 제안한 방법이 실제적인 하드웨어로 실시간 동작을 할 수 있음을 보였다.