• ETRI Journal
• /
• v.42 no.4
• /
• pp.549-561
• /
• 2020

We developed a 0.1-㎛ metamorphic high electron mobility transistor and fabricated a W-band monolithic microwave integrated circuit chipset with our in-house technology to verify the performance and usability of the developed technology. The DC characteristics were a drain current density of 747 mA/mm and a maximum transconductance of 1.354 S/mm; the RF characteristics were a cutoff frequency of 210 GHz and a maximum oscillation frequency of 252 GHz. A frequency multiplier was developed to increase the frequency of the input signal. The fabricated multiplier showed high output values (more than 0 dBm) in the 94 GHz-108 GHz band and achieved excellent spurious suppression. A low-noise amplifier (LNA) with a four-stage single-ended architecture using a common-source stage was also developed. This LNA achieved a gain of 20 dB in a band between 83 GHz and 110 GHz and a noise figure lower than 3.8 dB with a frequency of 94 GHz. A W-band image-rejection mixer (IRM) with an external off-chip coupler was also designed. The IRM provided a conversion gain of 13 dB-17 dB for RF frequencies of 80 GHz-110 GHz and image-rejection ratios of 17 dB-19 dB for RF frequencies of 93 GHz-100 GHz.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.234-242
• /
• 1998

Changes in transmission and thermoluminescent characteristics were used in order to find out the optimum growth condition of CsI single crystal scintillators which were made relatively defect-free using Czochralski method. Impurity distribution in the crystals and the intensity and number of thermoluminescent glow peaks decreased as the process of crystallization was repeated. The direction of crystal growth turned out to be (110), the crystal structure of grown CsI was bee, and its lattice constant was found to be $4.568{\AA}$. The activation energy (trap depths) of CsI:3rd was 0.45 eV and its frequency factor was $5.18{\times}10^5\;sec^{-1}$.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.87-92
• /
• 1996

The PLT thin films on (100) cleaved MgO single crystal substrate have been fabricated by rf magnetron sputtering using a PbO-rich target. The dependence of physical and electrical properties on the degree of c-axis orientation has been studied. The degree of c-axis orientation of PLT thin films depends on fabrication conditions. Fabrication conditions of the PLT thin films were such that substrate temperature, working pressure, gas ratio of $Ar/O_{2}$, and rf power density were $640^{\circ}C$, 10 mTorr, 10 seem, and $1.7\;W/cm^{2}$, respectively. In these conditions, the PLT thin film showed the Pb/Ti ratio of 1/2 at the surface, the resistivity of $8{\times}10^{11}{\Omega}{\cdot}cm$, and dielectric constant of 110. The pyroelectric infrared sensors with these PLT thin films showed the peak to peak voltage of 450 m V and signal to noise ratio of 7.2.

• New & Renewable Energy
• /
• v.18 no.2
• /
• pp.73-81
• /
• 2022

This study was aimed at designing a condenser, as a component of the organic Rankine cycle system for ships. The condenser was manufactured through press molding to achieve a bent shape to enhance the heat transfer performance, considering the shape of the heat transfer plate used in a brazing plate heat exchanger. The heat transfer plate was made of copper-nickel alloy. The required heat transfer rate for the condenser was 110 kW, and the maximum number of layers was set as 25, considering the characteristics of high-temperature brazing. Computational fluid dynamics techniques were used to perform the thermal fluid analysis, based on the ANSYS CFX (v.18.1) commercial program. The heat transfer rate of the condenser was 4.96 kW for one layer (width and length of 0.224 and 0.7 m, respectively) of the heat transfer exchanger. The fin efficiency pertaining to the heat transfer plate was approximately 20%. The heat flow analysis for one layer of the heat exchanger plate indicated that the condenser with 25 layers of heat transfer plates could achieve a heat transfer rate of 110 kW.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.6
• /
• pp.110-116
• /
• 2021

W3C enacted RDF(Resource Description Framework based DCAT meta data standard, which is world-widely accepted so far. To guarantee the inter-operability and integrity of data from various sources and even from various countries, it is considered that transportation meta data should also follow the DCAT standard. But still, to represent the transportation domain-specific features, it is necessary to define new properties and vocabularies in addition to the DCAT standard. This research identified the additional properties and vocabularies for transportation metadata, considering uniqueness of transportation data. The revised RDF schema and RDF graph proposed in this research should be able to lead the transportation open data platform revitalization.

• Journal of Korean Society of Forest Science
• /
• v.103 no.3
• /
• pp.402-407
• /
• 2014

In this study, Italy poplar(Populus euramericana) was selected for test specimen to measure cutting power when it harvested. The experiment has been controlled as three levels of feed rate (0.41, 1.25 and 2.5 m/s), sawing speed (800, 1,000 and 1,200 rpm), and the five levels of root collar diameter (50, 70, 90 and 110, 130 mm). The harvested volume after 3 years (root collar diameter 50 mm) was 10.5 tons, which falls short of the target amount of biomass is 20~30 ton/ha. In addition, the biomass amount of diameter 90 and 110 mm which reached the target amount were estimated to be 23.5 and 32.5 ton/ha respectively. As a result of experiment, it was found out that power of 128.2 and 175.8 W are consumed in case of cutting with the feed rate of 0.41m/s and minimum sawing speed (800 rpm) respectively. With the working area of 0.3 ha/h, it is considered to present working capacities of 16.5 and 22.8 ton/h respectively. The power consumed at the feed rate of 1.25 m/s is estimated to be 113.8 and 153.7W respectively and working capacity in a working area of 1 ha/h is estimated to be 23.5 and 32.5 ton/h. The power consumed at the feed rate of 2.5 m/s is estimated to be 119.8 and 166.9 W respectively and working capacity in a working area of 2 ha/h is estimated to be 47.0 and 65.5 ton/ha respectively. Therefore, the power source of harvest machine at the feed rate of 1.25, 2.50 m/s and sawing speed of 800 rpm shall be selected as it can process the target amount of estimated biomass.

• Korean Journal of Materials Research
• /
• v.6 no.3
• /
• pp.341-346
• /
• 1996

R-sapphire 기판위에 rf magnetron 스퍼터 방법으로 ZnO 박막을 증착하여 박막의 증착변수에 따른 결정성장방향과 SAW 특성을 분석하였다. 증착온도, 압력, rf 전력에 의해 박막 성장면이 (002)에서 (110)으로의 전이가 관찰되었다. 5mTorr, 40$0^{\circ}C$, 250W의 rf 전력에서 가장 우수한 (110)방향의 에피 ZnO 압전 박막의 SAW 특성을 분석하기 위하여 제작된 마스크를 사용하여 IDT를 구성한 후 SAW 특성을 분석한 결과 h/λ=0.08의 조건에서 전단속도가 약 5232m/s로서 고주파용 SAW 필터의 제조에 적합한 특성을 보이고 있다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.1
• /
• pp.110-121
• /
• 1983

ASHRAE 표준을 참고로 하여 한국과학기술원(KAIST)에서 수정한 집열기 시험 장치의 주요부품 의 설계도면 및 Specification 등을 제시하였다. 또한 ASHRAE 표준 시험 절차를 재분석하고 KAIST에서 수정한 Test Loop를 시험하기 위한 실험절차의 개요도 설명하였다. ASHRAE 표준 상의 가장 중요한 실험인 (1) 집열기 시간 상수 실험과 (2) 수직에 가까운 입사각에 대한 효율 실 험 및 (3) 입사각 수정 계수 실험 등을 실제 태양 아래에서 실험하여 그 결과도 그림으로 제시하 였다. 본 연구를 통해서 얻은 결과로부터 다음과 같은 결론을 얻을 수 있었다. 한국 과학 기술원 에서 설계한 집열기 시험 장치는 ASHRAE의 표준 절차에 따라 액체 가열식 집열기의 열효율을 측정하기 위한 실용적 장치임을 알 수 있다. 일반적으로 ASHRAE 표준 93-77은 합리적인 절차 라고 할 수 있다. 그러나, 최소일사량 규정(즉 630W/m$^{2}$ 미만이 되어서는 안된다고 하는 ASHRAE 규정) 같은 것은 일사량이 적은 기후 조건하에서는 다소 하향 조정하여도 정확한 효율 곡선을 얻을 수 있다고 하겠다.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.441-447
• /
• 1996

Sb doped SnO2(ATO:Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using oxide target and the deposition characteristics were investigated. The experimental conditions are as follows :Ar flow rate : 100 sccm oxygen flow rates ; 0-100 sccm deposition temperature ; 250 -40$0^{\circ}C$ DC sputter powder ; 150~550 W and sputtering pressure ; ; 2~7 mTorr. Deposition rate greatly depends not on the deposition temperature but on the reaction pressure oxygen flow rate and sputter power,. when the sputter powder is low ATO thin films with (110) preferred orientation are deposited. And when the sputter power is high (110) prefered orientation appeares with decreasing of oxygen flow rate and increasing of suputte-ring pressure.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.843-849
• /
• 1989

Effect of Bi2O3/Li2CO3 on low temperature sinteirng and dielectric property of BaTiO3 ceramics has been investigated. For the specimen sintered at 110$0^{\circ}C$, it was densified to 96% of BaTiO3 theoretical density by the addition of 1.0-1.25w/o Bi2O3/Li2CO3. Maximum dielectric constant increased and Curie temperature lowered with the increase of Bi2O3/Li2CO3 content, which probably can be explained by thne substitution of Bi3+, Li1+ on BaTiO3 lattice. The volatilization of Li1+, resulting from the increase of soaking time at 110$0^{\circ}C$ leads to the increase of Curie temperature and tetragonality of the specimen.