• International Journal of Automotive Technology
• /
• 제7권4호
• /
• pp.441-448
• /
• 2006

In-cylinder flows such as tumble and swirl play an important role on the engine combustion efficiencies and emission formations. The tumble flow, which is dominant in current high performance gasoline engines, is able to effect fuel consumptions and emissions under a partial load condition in addition to the volumetric efficiency under a wide open throttle condition. Therefore, it is important to optimize the tumble ratio of a gasoline engine for better fuel economy, lower emissions, and maximum volumetric efficiency. First step for optimizing a tumble ratio is to measure a tumble ratio accurately. For a tumble ratio measurement, many different methods have been developed and used such as steady flow rig, PIV, PTV, and LDV. However, it is not well known about the relations among the measured tumble ratios using different methods. The purpose of this research is to correlate the tumble ratios measured using three different methods and find out merits and demerits of each measurement method. In this research the tumble flow was measured, compared, and correlated using three different measurement methods at the same engine: steady flow rig; 2-dimensional PIV; and 3-dimensional PTV water flow rig.

• 재활복지공학회논문지
• /
• 제10권4호
• /
• pp.259-265
• /
• 2016

본 논문에서는 폐질환 조기 검출을 위하여 Broncho vascular, Emphysema, Ground Glass Reticular, Ground Glass, Honeycomb, Normal의 6가지 폐조직에 대한 새로운 분류기법을 제안하였다. 단순 베이즈 분류기와 아다부스트 학습 기법을 도입하여 459개의 결합 히스토그램 특징인자로부터 유효한 특징인자를 선별함으로써 폐조직을 분류하였다. 다중 해상도 해석, 체적 LBP 및 CT 휘도를 기반으로 하는 결합 히스토그램 특징인자는 정확도, 민감도, 특이도 결과에서 기존의 3D AMFM보다 우수한 결과를 보였다. 제안한 특징인자와 3D AMFM 특징인자의 정확도는 각각 90.1%과 85.3%로서 제안한 특징인자의 우수한 분류 성능을 확인하였다.

• Journal of Electrochemical Science and Technology
• /
• 제3권3호
• /
• pp.135-142
• /
• 2012

Over the past few years, $LiFePO_4$ has been actively studied as a cathode material for lithium-ion batteries because of its advantageous properties such as high theoretical capacity, good cycle life, and high thermal stability. However, it does not have a very good power capability owing to the low lithium-ion diffusivity and poor electronic conductivity. Reduction in particle size of $LiFePO_4$ to the scale of nanometers has been found to dramatically enhance the above properties, according to many earlier reports. However, because of the intrinsically low tap density of nanomaterials, it is difficult to commercialize this method. Many studies are being carried out to improve the volumetric energy density of this material and many methods have been reported so far. This paper provides a brief summary of the synthesis methods and electrochemical performances of micro-spherical $LiFePO_4$ having high volumetric energy density.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.299-306
• /
• 2005

Anaerobic fermentation of food waste (FW) and waste activated sludge (WAS) for hydrogen production was performed in CSTR (Continuous Stirred tank reactor) under various HRTs and volumetric mixing ratio (V/V) of two substrates, FW and WAS. The specific hydrogen production potential of FW was higher than that of WAS. However, pH drop in the CSTR for hydrogen production from FW was higher than that from WAS. The maintenance of desired pH during fermentative hydrogen production is regarded as the most important operation parameter for the stable hydrogen production. Therefore, when the potential of hydrogen production from FW and better buffer capacity of WAS, the proper mixture of FW and WAS for fermentative hydrogen production were considered as a useful complementary substrate. The maximum yield of specific hydrogen production, 140 mL/g VSS, was found at HRT of 2 day and the volumetric mixing ratio of 20:80 (WAS : FW). The spatial distribution of hydrogen producing bacteria was observed in anaerobic fermentative reactor using fluorescent in situ hybridization (FISH) method.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 춘계학술대회
• /
• pp.72-74
• /
• 1997

We have developed a 3-D image processing and display technique that include image resampling, modification of MIP, and fusion of MIP image and volumetric rendered image. This technique facilitates the visualization of the three-dimensional spatial relationship between vasculature and surrounding organs by overlapping the MIP image on the volumetric rendered image of the organ. We applied this technique to a MR brain image data to produce an MRI angiogram that is overlapped with 3-D volume rendered image of brain. MIP technique was used to visualize the vasculature of brain, and volume rendering was used to visualize the other structures of brain. The two images are fused after adjustment of contrast and brightness levels of each image in such a way that both the vasculature and brain structure are well visualized either by selecting the maximum value of each image or by assigning different color table to each image. The resultant image with this technique visualizes both the brain structure and vasculature simultaneously, allowing the physicians to inspect their relationship more easily. The presented technique will be useful for surgical planning for neurosurgery.

• 대한기계학회논문집A
• /
• 제21권5호
• /
• pp.835-841
• /
• 1997

Microscopic examination of the morphology of wear debris is an accepted method for machine condition and fault diagnosis. However wear particle analysis has not been widely accepted in industry because it is dependent on expert interpretation of particle morphology and subjective assessment criteria. This paper was undertaken to analyze the morphology of wear debris for machine condition diagnosis of the lubricated moving surfaces by image processing and analysis. The lubricating wear test was performed under different sliding conditions using a wear test device made in our laboratory and wear testing specimen of the pin-on-disk-type was rubbed in paraffine series base oil. In order to describe characteristics of debris of various shape and size, four shape parameters (50% volumetric diameter, aspect, roundness and reflectivity) have been developed and outlined in the paper. A system using such techniques promises to obviate the need for subjective, human interpretation of particle morphology in machine condition monitoring, thus to overcome many of the difficulties in current methods and to facilitate wider use of wear particle analysis in machine condition monitoring.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1845-1850
• /
• 2003

The underground utility tunnels are important facility as a mainstay of country because of communication developments. The communication and electrical duct banks as well as various utility lines for urban life are installed in the underground utility tunnel systems. If a fire breaks out in this life-line tunnel, the function of the city will be discontinued and the huge damages are occurred. In order to improve the safety of life-line tunnel systems and the fire detection, the behaviors of the fire-induced smoke flow and temperature distribution are investigated. In this study we assumed that the fire is occurred at the contact or connection points of cable. Numerical calculations are carried out using different velocity of ventilation in utility tunnel. The fire source is modeled as a volumetric heat source. Three-dimensional flow and thermal characteristics in the underground tunnel are solved by means of FVM (Finite Volume Method) using SIMPLE algorithm and standard ${\kappa}-{\varepsilon}$ model for Reynolds stress terms. The numerical results of the fire-induced flow characteristics in an underground utility tunnel with different velocity of ventilation are graphically prepared and discussed.

• 성인간호학회지
• /
• 제15권4호
• /
• pp.520-530
• /
• 2003

Purpose: The objective of the study was to identify the effects of the meridian massage therapy on hand edema and hand functions in patients with hemiplegia. Method: The experiment was conducted in the Oriental Medical ward of "K" hospital during the period of 2000. 12. 15 - 2001. 03. 15. Fifty five subjects with hemiplegia following a stroke participated in the study. Volumetric size of the hand and the circumference of the index finger of each patient was measured and functional points were recorded for pre and post experiment. Result: 1. Apparent decrease in volumetric size of the hand and the circumference of the index finger(p=.022. p=.021), and higher functional points(p=.003) in the experimental group in comparison to the control group. 2.Volume of hands & their functions appeared to be irrelevant(r=-.195, p=.154). 3. Circumference of the index finger & their functions also turned out to be irrelevant (r=-.110, p=.424). Conclusion: Meridian massage is an effective nursing interventional therapy to relieve hand edema and improve hand functions in hemiplegic patients and has great potential for use in a wide range of medical fields as an efficient supplementary treatment for stroke rehabilitation.

• 대한원격탐사학회지
• /
• 제27권3호
• /
• pp.225-234
• /
• 2011

This study proposes an inversion algorithm to extract the surface parameters, such as surface roughness and soil moisture contents, using multi-frequency SAR data. The study areas include the tidal flats of Jebu Island and the reclaimed lands of Hwaong district on the western coasts of the Korean peninsula. SAR data of three frequencies were accordingly calibrated to provide precise backscattering coefficients through absolute radiometric calibration. The root mean square (RMS) height and the correlation length, which can describe the surface roughness, were extracted from the backscattering coefficients using the inversion of the Integral Equation Method (IEM). The IEM model was appropriately modified to accommodate the environmental conditions of tidal flats. Volumetric soil moisture was also simultaneously extracted from the dielectric constant using the empirical model, which define the relations between volumetric soil moistures and dielectric constants. The results obtained from the proposed algorithm were verified with the in-situ measurements, and we confirmed that multi-frequency SAR observations combined with the surface scattering model for tidal flats can be used to quantitatively retrieve the geophysical surface parameters in tidal flats.

• 폴리머
• /
• 제25권2호
• /
• pp.293-301
• /
• 2001

새로운 복합재료 제조 기술인 electron-ion technology (EIT)를 이용하여 전도성 탄소섬유/고밀도 폴리에틸렌 (CF/HDPE) 복합필름을 제조하고 탄소섬유 에폭시 sizing이 제조된 필름의 체적비저항과 인장강도 그리고 계면 특성에 미치는 영향에 대하여 연구하였다. 에폭시 sizing은 tunneling 효과를 좋게 해서 복합재료 필름의 전도성을 향상시키는 반면, 극성인 에폭시 sizing은 무극성인 폴리에틸렌과의 친화성이 없어서 탄소섬유와 폴리에틸렌간의 계면결합력을 감소시키므로 에폭시 sized 탄소섬유(CF(S))는 unsized 탄소섬유(CF(U))에 비하여 필름의 체적비저항과 인장강도를 감소시켰다. 에폭시 sizing은 탄소섬유의 nucleating efficiency를 떨어뜨려서 CF(S)/HDPE 필름이 CF(U)/HDPE 필름보다 불규칙적이고 덜 발달된 transcrystalline layer를 형성함을 관찰할 수 있었다.