• Advances in materials Research
• /
• v.5 no.2
• /
• pp.93-105
• /
• 2016

KNN-based ceramics modified with small amounts of $Bi_4Zr_3O_{12}$ (BiZ) has been synthesized using high-throughput experimentation (HTE). The results from X-ray diffraction show that for samples with base composition $(K_{0.5}Na_{0.5})NbO_3$ (KNN), the phase present changes from orthorhombic to pseudo-cubic with more than 0.2 mol% BiZ addition; for samples with base composition $(K_{0.48}Na_{0.48}Li_{0.04})(Nb_{0.9}Ta_{0.1})O_3$ (KNNLT), the phase present changes from a mixture of orthorhombic and tetragonal symmetry to pseudo-cubic with more than 0.4 mol % while for samples with base composition $(K_{0.48}Na_{0.48}Li_{0.04})(Nb_{0.86}Ta_{0.1}Sb_{0.04})O_3$ (KNNLST), the phase present is tetragonal with <0.3 mol% BiZ addition and transforms to pseudo-cubic with more dopant addition. The microstructures of the samples show that addition of BiZ decreases the average grain size and increases the volume of pores at the grain boundaries. The values of dielectric constant for KNN and KNNLT compositions increase slightly with BiZ addition while that for KNNLST decreases gradually with BiZ addition. The dielectric loss values are between 0.02 and 0.04 for KNNLT and KNNLST compositions while they are ~ 0.05 for KNN samples. The resistivity values increases with BiZ addition and values in the range of $10^{10}{\Omega}cm$ and $10^{12}{\Omega}cm$ are obtained. The piezoelectric charge coefficient ($d{^*}_{33}$) is highest for KNNLST samples and decreases gradually from ~400 pm/V to ~100 pm/V with BiZ addition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.200-203
• /
• 2003

A study on the arc resistance and light reflectance of PTFE (polytetrafluoroethylene) nozzle for circuit breaker is presented. PTFE has been used widely as a material for circuit breaker nozzle. PTFE has excellent electrical resistivity, high melt viscosity, chemical inertness, heat resistance and low loss factor. PTFE melts at $327\;^{\circ}C$ but the viscosity is very high above the melting point. In the arcing environment in a circuit breaker, the fraction of the power is emitted out of the arc and reaches the nozzle wall by radiation, causing ablation at the surface and in the depth of the wall. Some fraction of the radiation power emitted out of the arc directly break up the chemical bonds at the surface while some fraction of the radiation power penetrates into the wall, heats up the material to evaporation temperature and causes damages deeper inside the volume of the nozzle. In this paper, some fillers that have endurance in the high temperature arc environment were added into PTFE. Adding some fillers into PTFE was expected to be efficient in improving the endurability against radiation. The light reflectance and arc resistance of PTFE composites were investigated.

• Journal of the Korean Geophysical Society
• /
• v.5 no.1
• /
• pp.29-39
• /
• 2002

Geophysical data sets from the Chojeong area in the Chungbok-Do are compositely studied in terms of multi-attribute interpretations for the subsurface mappings of shallow fracture zones, associated with groundwater reservoir. Utilizing a GIS software, the attribute data were implemented to a database; a lineament from the satellite image, electrical resistivities and its standard deviation, radioactivity, seismic velocity, and bedrock depth. In an attempt to interpret 1-D electrical sounding data in 3-D views, 1-D data are firstly performed horizontal and vertical inter- and extrapolation. Reconstruction of a resistivity volume is found to be an effective scheme for subsurface mapping of shallow fracture zones. Shallow fracture zones are located in the southeastern part of the study area, which are commonly correlated with the various exploration data.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1256-1261
• /
• 2018

Both thermoplastic formability and electrical conductivity of Al-Ni-Y metallic glass with 12 different compositions have been investigated in the present study with an aim to apply as a functional material, i.e. as a binder of Ag powders in Ag paste for silicon solar cell. The thermoplastic formability is basically influenced by thermal stability and fragility of supercooled liquid which can be reflected by the temperature range for the supercooled liquid region (${\Delta}T_x$) and the difference in specific heat between the frozen glass state and the supercooled liquid state (${\Delta}C_p$). The measured ${\Delta}T_x$ and ${\Delta}C_p$ values show a strong composition dependence. However, the composition showing the highest ${\Delta}T_x$ and ${\Delta}C_p$ does not correspond to the composition with the highest amount of Ni and Y. It is considered that higher ${\Delta}T_x$ and ${\Delta}C_p$ may be related to enhancement of icosahedral SRO near $T_g$ during cooling. On the other hand, electrical resistivity varies with the change of Al contents as well as with the change of the volume fraction of each phase after crystallization. The composition range with the optimum combination of thermoplastic formability and electrical conductivity in Al-Ni-Y system located inside the composition triangle whose vertices compositions are $Al_{87}Ni_3Y_{10}$, $Al_{85}Ni_5Y_{10}$, and $Al_{86}Ni_5Y_9$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.603-608
• /
• 2023

Carbon black with high purity and excellent conductivity is used as a conductive filler in the semiconductive compound for EHV (Extra High Voltage) power cables of 345 kV or higher. When carbon black and CNT (carbon nanotube) are applied together as a conductive filler of a semiconductive compound, stable electrical properties of the semiconductive compound can be maintained even though the amount of conductive filler is significantly reduced. In EHV power cables, since the semi-conductive layer is close to the conductor, stable electrical characteristics are required even under high-temperature conditions caused by heat generated from the conductor. In this study, the theoretical principle that a semiconductive compound applied with carbon black and CNT can maintain excellent electrical properties even under high-temperature conditions was studied. Basically, the conductive fillers dispersed in the matrix form an electrical network. The base polymer and the matrix of the composite, expands by heat under high temperature conditions. Because of this, the electrical network connected by the conductive fillers is weakened. In particular, since the conductive filler has high thermal conductivity, the semiconductive compound causes more thermal expansion. Therefore, the effect of CNT as a conductive filler on the thermal conductivity, thermal expansion coefficient, and volume resistivity of the semiconductive compound was studied. From this result, thermal expansion and composition of the electrical network under high temperature conditions are explained.

• Journal of the Korean Chemical Society
• /
• v.36 no.1
• /
• pp.16-23
• /
• 1992

High $T_c$, superconductor $(Y_{1-x}Eu_x)Ba_2Cu_3O_{7-{\delta}}$ (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were prepared and the physical properties were observed. XRD analysis showed that the structures of all the specimen were orthorhombic and the lattice parameters a, b and c increased with the increasing x value. Electrical resistivity and magnetization measurements revealed that pure high $T_c$, superconducting phases were formed at above 90 K. The critical temperatures increased with increasing the amount of Eu. From the measurement of magnetization and the size of the grains using SEM micrographs, volume diamagnetic susceptibilities for each specimen were calculated. These values decreased with the increasing x value. The composition of Ba in the lattice site decreased as the concentration of Eu increased, and this was confirmed by EPMA. It was found out that the volume diamagnetic susceptibility of each specimen was directly influenced by the composition of Ba in the lattice site.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.643-648
• /
• 2014

The accelerated thermal aging of CSPE (chlorosulfonated polyethylene) was carried out for 40.41, 121.22, and 202.04 days at $100^{\circ}C$, which are equivalent to 20, 60, and 100years of aging at $50^{\circ}C$, respectively. The volume electrical resistivities of the accelerated thermally aged CSPE samples for 0, 40.41, 121.22, and 202.04 days were $1.107{\times}10^{14}-2.097{\times}10^{14}$, $7.752{\times}10^{13}-1.556{\times}10^{14}$, $7.693{\times}10^{13}-1.521{\times}10^{14}$, and $7.380{\times}10^{13}-1.304{\times}10^{14}{\Omega}{\cdot}cm$, respectively, at room temperature. The permittivities of the accelerated thermally aged CSPE samples for 0, 40.41, 121.22, and 202.04 days were $2.89{\times}10^{-11}-3.65{\times}10^{-11}$, $3.40{\times}10^{-11}-3.70{\times}10^{-11}$, $3.50{\times}10^{-11}-3.82{\times}10^{-11}$, and $3.76{\times}10^{-11}-4.13{\times}10^{-11}$ F/m, respectively, at room temperature. The EAB (elongation at break) of the accelerated thermally aged CSPE samples for 0, 40.41, 121.22, and 202.04 days were 98.8-101.3, 59.5-60.3, 37.8-39.2, and 41.8-44.3%, respectively, at room temperature. The apparent densities of the accelerated thermally aged CSPE samples for 0, 40.41, 121.22, and 202.04 days were 1.603-1.614, 1.611-1.613, 1.622-1.628, and $1.618-1.620g/cm^3$, respectively, at room temperature. The measured currents of the accelerated thermally aged CSPE and the standard sample were almost constant after 5 min of applying a 300-V/mm electric field to the CSPE. The V-I slope of the accelerated thermally aged CSPE sample was increased if the applied electric field was increased at room temperature, and the V-I slope of the accelerated thermally aged CSPE was higher than that of standard CSPE.

• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.73-86
• /
• 1999

The ion-exchange method for the purification of primary coolant has been used broadly in PWR(pressurized water reactor)-type nuclear power plants due to its high decontamination efficiency, simple system, and easy operation. However, its non-selective removal of metal and non-radionuclides shortens its life, resulting in the generation of a large amount of waste ion-exchange resin. In this study, the feasibility of electrodeionization (EDI) was investigated for the purification of primary cooling water using synthetic solutions under various experimental conditions as an alternative method for the ion exchange. The results shows that as the feed flow-rate increased, the removal efficiency increased and the power consumption decreased. The removal rate was observed as a 1000 decontamination factor(DF) at a nearly constant level. For the synthetic solution of 3 ppm TDS (Total Dissolved Solid), the power consumption was 40.3 mWh/L at 2.0 L/min of feed flow rate. The higher removal rate of metal species and lower power consumption were obtained with greater resin volume per diluting compartment. However, the flow rate of the EDI process decreased with the elapsed time because of the hydrodynamic resistivity of resin itself and resin fouling by suspended solids. Thus, the ion-exchange resin was replaced by an ion-conducting spacer in order to overcome the drawback. The system equipped with the ion-conducting spacer resolved the problem of the decreasing flow rate but showed a lower efficiency in terms of the power consumption, the removal rate of metal species and current efficiency. In the repeated batch operation, it was found that the removal efficiency of metal species was stably maintained at DF 1000.

• Polymer(Korea)
• /
• v.28 no.2
• /
• pp.143-148
• /
• 2004

${\alpha}$,$\omega$-Hydrogen polyorganosiloxane(HPMDMS) prepolymer was prepared from equilibrium polymerization ofoctamethylcyclotetrasiloxane, 1,3,5-trimethylcyclotrisiloxane, 1,3,5,7-tetravinyl-1,3,5,7-tetramethyl-cyclotetrasiloxane, and 1,1,3,3-tetramethyl disiloxane as an end-blocker in the presence of tetramethylammonium siloxanolate as a catalyst. Polyorganosiloxane modified with dimethylacrylamide(APMDMS) was prepared by hydrosilylation of HPMDMS with dimethylacrylamide in the presence of Pt catalyst, and followed by coordination of metal oxide (APMDMS-MO), such as NiO and FeO, to the amide moieties of the resulting polymer. The chemical structures of HPMDMS and APMDMS were confirmed by FT-IR and $^1$H-NMR analysis. Liquid silicone rubber containing metal oxide composite (LSRMO) was prepared by compounding APMDMS-MO, ${\alpha}$,$\omega$-vinylpolydimethylsiloxane, and a catalyst in a high speed dissolver. The thermal conductivity of LSRMO composite was determined to be 0.29 W/mK, and the volume resistivity exhibited a lower value than that of LSR composite. The mechanical and thermal properties of LSRMO and LSR composite were measured by UTM and TGA.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.496-503
• /
• 1996

Aromatic and aliphatic copolyesters for the dispersing agent were synthesized by two stage reaction, esterification and polycondensation. Copolyesters were blended with PET in the melt state and their thermal and rheological properties were investigated. From GPC analysis Mn's and Mw's of copolyesters were about 30000 and 65000g/mol, respectively. From DSC experiment copolyesters had melting range of $90{\sim}150^{\circ}C$. Copolymer composition was in good agreement with comonomer feed ratio from $^1H$-NMR analysis. Copolyesters and SPA (standard sample) were blended with PET in the melt state. From DSC experiment, copolyesters and SPA were miscible with PET. From the dynamic melt viscosity experiment, melt viscosity of blended sample was increased as the content of aromatic copolyester was increased, while it was decreased as the content of aliphatic and SPA were increased. As for volume resistivity of dry color containing carbon black and copolyesters with dispersing time, aromatic copolyester showed highest value. It was conferred from this result that aromatic copolyester was the best dispersing agent for carbon black in PET resin.