• 전기학회논문지
• /
• 제67권5호
• /
• pp.635-643
• /
• 2018

This paper propose a method to identify the motor parameters and improve input voltage error which affect the low speed position error of the back-emf(back electromotive force) based sensorless algorithm and to secure the operation reliability and stability even in the case where the load fluctuation is severe and the start and low speed operation frequently occurs. In the model-based observer used in this paper, stator resistance, inductance, and input voltage are particularly influential factors on low speed performance. Stator resistance can cause resistance value fluctuation which may occur in mass production process, and fluctuation of resistance value due to heat generated during operation. The inductance is influenced by the fluctuation due to the manufacturing dispersion and at a low speed where the change of the current is severe. In order to find stator resistance and inductance which have different initial values and fluctuate during operation and have a large influence on sensorless performance at low speed, they are commonly measured through 2-point calculation method by 2-step align current injection. The effect of voltage error is minimized by offsetting the voltage error. In addition, when the command voltage is used, it is difficult to estimate the back-emf due to the relatively large distortion voltage due to the dead time and the voltage drop of the power device. In this paper, we propose a simple circuit and method to detect the voltage by measuring the PWM(Pulse Width Modulation) pulse width and compensate the voltage drop of the power device with the table, thereby minimizing the position error due to the exact estimation of the back-emf at low speed. The suitability of the proposed algorithm is verified through experiment.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.752-760
• /
• 2018

In this paper, interior permanent magnet synchronous motor (IPMSM) design for sensorless drive, considering magnetic neutral point shift according to magnetic saturation, has been proposed. Sensorless control was divided into a method based on inductance and a method based on back induced voltage. Because induced voltage is very small at zero or low speed, error in rotor initial position estimation may occur. Using the ratio of saliency addresses this problem. When using high-frequency injections at low speed, the rotor's initial position is estimated at the smallest portion of the inductance. IPMSM has the minimum inductance at the d-axis. However, if magnetic saturation leads to magnetic neutral point variation, following the load current change, there is a change in the minimum point of inductance. In this case, it can lead to failure of initial rotor position estimation. As a result, it is essential that the blocking design has an inductance minimum point shift. As such, in this study, an IPMSM design method, by blocking magnetic neutral point change, has been proposed. After determining the inductance profile based on the finite element analysis (FEA), the results of proposed method were verified.

• Journal of Power Electronics
• /
• 제9권1호
• /
• pp.1-17
• /
• 2009

Permanent magnet brushless DC (PMBLDC) motors are the latest choice of researchers due to their high efficiency, silent operation, compact size, high reliability and low maintenance requirements. These motors are preferred for numerous applications; however, most of them require sensorless control of these motors. The operation of PMBLDC motors requires rotor-position sensing for controlling the winding currents. The sensorless control would need estimation of rotor position from the voltage and current signals, which are easily sensed. This paper presents state of the art PMBLDC motor drives with an emphasis on sensorless control of these motors.

• 한국정보통신학회논문지
• /
• 제20권5호
• /
• pp.998-1004
• /
• 2016

3상 PWM 컨버터는 입력 전류를 정현적으로 제어할 수 있어 입력 전류의 고조파 성분을 감소시킬 수 있고 입력 전압에 대하여 입력 전류의 위상을 제어할 수 있다. 본 논문은 3상 PWM 컨버터의 역률개선을 위하여 전원전압센서를 사용하지 않고 가상자속기반 벡터제어를 적용한 새로운 센서리스 제어방식을 연구하였다. 직류출력전압은 칼만 필터를 적용하여 추정한 가상자속에 의해 제어되며, 동기위상은 추정된 가상자속을 이용하여 위상을 얻는다. 제시한 PFC 알고리즘은 역률개선 및 가변영역에서 직류출력전압, 부하변동에서 직류출력전압을 정밀하게 제어할 수 있는 우수성을 가진다. 본 논문에서 제안한 가상자속추정 알고리즘을 적용한 칼만 필터 성능은 실험과 시뮬레이션을 통해서 검증하였다.

• 전력전자학회논문지
• /
• 제21권5호
• /
• pp.449-452
• /
• 2016

This paper presents a simplified analysis on the rotor position detection error in sensorless interior permanent magnet brushless DC motor (BLDCM) drives, wherein terminal voltage sensing based on the back-electromotive force (back-EMF) zero-crossing point detecting circuitry is employed. The effect of a rotor saliency on the back-EMF's zero-crossing point detection is analyzed using the extended EMF-based voltage equation of the interior permanent BLDCM in a stationary reference frame, and thus the overall analysis is considerably simplified compared to the conventional one. Simulation results are provided to verify the effectiveness of the proposed method.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.523-525
• /
• 2004

This paper describes a new method of detecting rotor position in switched reluctance motor(SRM). Some strategies of position sensorless control methods for the motor include the measurement of phase current and applied pulse voltage in an unexcited phase. The principle of the estimation of a rotor position is based on the detection of inductance by pulse currents. Suggested method is verified by some experimental tests.

• 조명전기설비학회논문지
• /
• 제28권9호
• /
• pp.1-7
• /
• 2014

Brushless Direct Current(BLDC) Motor is essential to measure a rotor position because of that this motor type needs to synchronize the rotor's position and changeover phase current instead of a brush and commutator used on the existing dc motor. Recently, many researches have studied on sensorless control drive for BLDC motor. The conventional control methods are a compensation value dq, Kalman filter, Fuzzy logic, Neurons neural network, and the like. These methods has difficulties of detecting BEMF accurately at low speed because of low BEMF voltage and switching noise. And also, the operation is long and complex. So, it is required a high-performance microprocessor. Therefore, it is not suitable for a small BLDC motor sensorless drive. This paper presents control methods suitable for economic small BLDC motor sensorless drive which are an improved design of the BEMF detection circuit, simplifying a complex algorithm and computation time reduction. The improved motor sensorless drive is verified stability and validity through being designed, manufactured and analyzed.

• 전력전자학회논문지
• /
• 제10권4호
• /
• pp.363-372
• /
• 2005

본 논문에서는 비선형 모델링 기법을 이용하여 matrix convertor로 구동되는 유도전동기 구동장치의 성능개선을 위한 새로운 센서리스 기법을 제안한다. 각 스위치에서 발생하는 전환지연과 스위치 소자의 전압강하등과 같은 matrix converter의 비선형 특성을 모델링하여 보상함으로써 저속영역에서의 속도제어성능을 향상시킨다. 전속도 영역에서의 속도 센서리스 제어성능을 향상시키기 위해 축소차원 확장 루엔버거 관측기를 적용하고, 제안한 관측기 이득의 설정방법을 제안한다. 실험을 통해 제안한 제어 알고리즘의 타당성을 검증한다

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.660-664
• /
• 2004

The indirect rotor position detection method using terminal voltage of brushless DC motor (BLDCM) requires simple control circuit, and has wide speed range of sensorless operation. However, because the substantial phase difference exists between real back emf and terminal voltage, the existing indirect detection method using analog filter which is affected by frequency, speed, and load sensitively cannot be synchronized with current, in the end, it advances or delays. This paper presents new analog filter circuit design for rotor position estimation in order to solve the problem, and proposes novel sensorless operation method which is stable even in high speed range and not influenced by parameters with analysis on phase difference by load and speed. Moreover, the appropriateness of the proposed sensorless drive in this paper is verified and analyzed by experimentation.

• Journal of Power Electronics
• /
• 제11권5호
• /
• pp.743-750
• /
• 2011

This article deals with the sensor-less control of a DC Motor via a SEPIC Converter-Full Bridge combination powered through solar panels. We simultaneously regulate, both, the output voltage of the SEPIC-converter to a value larger than the solar panel output voltage, and the shaft angular velocity, in any of the turning senses, so that it tracks a pre-specified constant reference. The main result of our proposed control scheme is an efficient linear controller obtained via Lyapunov. This controller is based on measurements of the converter currents and voltages, and the DC motor armature current. The control law is derived using an exact stabilization error dynamics model, from which a static linear passive feedback control law is derived. All values of the constant references are parameterized in terms of the equilibrium point of the multivariable system: the SEPIC converter desired output voltage, the solar panel output voltage at its Maximun Power Point (MPP), and the DC motor desired constant angular velocity. The switched control realization of the designed average continuous feedback control law is accomplished by means of a, discrete-valued, Pulse Width Modulation (PWM). Experimental results are presented demonstrating the viability of our proposal.