• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.27-33
• /
• 2007

A novel priming discharge technique in which the ramp shaped priming pulse is superposed on the sustain period so that the entire plasma display panel (PDP) is discharged at the same time with a single drive circuit is proposed. From the experimental results, it is ascertained that the priming discharge is ignited only in a pixel in which sustain discharge does not occur and it has been understood that the priming pulse hardly influences the sustain discharge. Moreover, high-speed driving with address pulse widths of 0.7[${\mu}s$] was achieved and a wide address voltage margin of 40[V] was obtained by using the drive method applied the proposed priming discharge technique. In these results, full-HDTV PDP with 1080 horizontal scanning lines can be driven without decreasing the brightness and the possibility of the commercializing is also high because this technology is designed for using the commercialized driver IC.

• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.5
• /
• pp.81-92
• /
• 2013

The satellite includes many release mechanisms such as solar array deployment, antenna deployment, cover to protect contamination in scientific equipment, pyro value of the propulsion subsytem, and bypass device in Li-Ion cell module. A drive the initiators is a critical to the successful mission because the initiators of release mechanism driving by the pyrotechnic circuit is operated in single short. The pyrotechnic circuit has to provide switching network for safety. A typical switching network has defect consisting of high current rating fire switch to handle switching transient current during fire the initiator. The pyrotechnic circuit is required some form of power conditioning to reduce the peak power demanded from the bus if the initiators are to be fired from the main bus. This paper design a pyrotechnic circuit synchronized to the fire-command to activate the fire switch to overcome use high current rating fire switch to handle switching transient current during fire the initiator. The pyrotechnic circuit provides a current limited widow pulse for fire current synchronized to the fire-command to insure that fire switch will only carry the current but never switch it. The current limited widow pulse for fire current can be possible to use low current rating and light mass switch in switching network. The current limit function in the pyrotechnic circuit reduces supply voltage to initiator and provides the effect of power conditioning function to reduce peak bus power. The pyrotechnic circuit to apply satellite development on geostationary orbit is verified the function by test in development model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.333-338
• /
• 2008

In this paper, a new NMOS current-mirror type bridge rectifier for driving RFID chips, whose minimum input voltage required to obtain the effective DC output voltage is low enough and whose power dissipation can be reduced than that of conventional one, is proposed. The designed rectifier is able to supply high enough and well-rectified DC voltages to drive RFID transponder chips for the frequency range of 13.56 MHz HF(for ISO 18000-3), 915 MHz UHF(fur ISO 18000-6), and 2.45 GHz microwave(for ISO 18000-4). Output characteristics of the proposed rectifier are analyzed with the high frequency equivalent circuit. And the circuitry method for effective reducing of the gate leakage current due to the increasing of operating frequency is also proposed theoretically. Using this method, the power consumption of $100\;{\mu}W$ and the DC output voltage of 2.13V for 3V peak-to-peak input voltage and $45\;K{\Omega}$ load resistance are obtained. Compared to conventional one, the proposed rectifier operates in more stable and shows superior characteristics in UHF and microwave frequencies.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.584-588
• /
• 2021

The impedance of the speaker is likely to be recognized as a fixed value. However, speaker impedance continues to vary with frequency variation, especially larger in resonant frequency region. The sound pressure level of loudspeakers is determined by the current flowing throughout the coil that consists loudspeakers. If loudspeakers are driven by voltage, sound pressure level of the loudspeaker is distorted by the variation of loudspeaker impedance. Current-drive of loudspeakers can solve this problem, but distortion of sound pressure level occurs in low frequencies due to resonance. The distortion can degrade the sound quality of the sound system. So to solve this problem, In this paper, we propose a resonance compensation circuit using DSP. we simulates audio systems using an equivalent model of loudspeakers to verify distortion of sound pressure level due to impedance variation and propose a circuit to compensate it. The proposed circuit is configured using a state variable filter and it can adjust the center frequency and output, so it will be used various sound systems.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.506-513
• /
• 2001

The torque of an SRM depends on the phase current and derivative of inductance. But an SRM is difficult to control the desired torques because of saturation in magnetic circuit An SRM is controlled by parameters of input voltage, and switch on , off angle The switch on off angles of an SRM regulate the magnitude and shape of current waveform and decide the magnitude and shape of torque This paper proposes an the optimization control scheme by adjusting both the switch on an switch off angle . The switch off angles are decided by reference of efficiency using simulation and experiments. The switch on angles are decided by load torque , And the dwell angles are controlled for torque control and speed control using GA-neural network which is used to simulated the reasonable switching angle.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 1995

This paper deals with the modeling and simulation to control the torque and speed of an induction motor using field-oriented control methods. Rotor flux is estimated using the indirect sensing method based on the rotor circuit equation in the synchronously rotation reference frame, and slip angle and rotor position are calculated from rotor angular velocity and stator current. As results of modeling and digital simulation with a voltage source inverter, it is shown that the proposed scheme gives good static and dynamic performance to the induction motor drive.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1995.05a
• /
• pp.171-175
• /
• 1995

Semiconductor diode lasers that can generate one watt or more of optical energy for tens of milliseconds (quasi continuous wave) are now readily available. Several researchers have demonstrated that this power level, when properly coupled, can reliably initiate pyrotechnic mixtures. This means that the initiator containing the pyrotechnic can be protected against inadvertent initiation from electromagnetic radiation or electrostatic discharge by a conducting Faraday cage surrounding the explosive. Only a small dielectric window penetrates the housing of the initiator, thereby eliminating the conductors necessitated by a bridgewire electroexplosive device. The diode laser itself, however, functions at a low voltage (typically 3 volts) and hence is susceptible to inadvertent function from power supply short circuits, electrostatic discharge or induced RF energy. The rocket motor arm-fire device de-scribed in this paper uses a diode laser, but protects it from unintentional function with a Radio Frequency Attenuating Coupler (RFAC).The RFAC, invented by ML Aviation, a UK company, transfers power into a Faraday cage via magnetic flux, thereby protecting the diode, its drive circuit and the pyrotechnic from all electromagnetic and electrostatic hazards. The first production application of a diode laser and RFAC device was by the Korean Agency for Defense Development.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.6
• /
• pp.24-30
• /
• 2009

We compared 3 kinds of ignitor characteristics and represented the procedure in order to turn the HID lamp on. Also, we analysed the cable characteristic based on the length between ignitor and the HID lamp and proved it theoretically. In practice, the ignition voltage contains a lot of problems because it is easily changed by the structure of ignitors, cable length and characteristics. In this paper, therefore, 3 ignitors, which are LC resonant typed, arc-gap circuit typed and drive frequency variable typed, have simulated and analysed with the 25[m] cable length. After careful consideration of comparisons made of all the ignitors' and cables' characteristics, a number of possible solutions were finalized.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.749-752
• /
• 1993

This paper deals with the development of three phase 440[V], 500[KVA] Inverter system using the IGBT Devices. IGBT's have been used very successfully in variable frequency induction motor drive equipment. Problems associated with power devices characteristics when power devices are operated in parallel, such as balanced switching behavior and thermal stability, can be solved by using NPT type IGBT's. By Experimental results, it is confirmed that the voltage overshoot and reverse recovery current was very low. The equipment had proved to be reliable and short circuit proof. In addition, the performances in term of thermal characteristics, protection functions and stability are satisfactory.