• Journal of Korea Foundry Society
• /
• v.41 no.5
• /
• pp.434-444
• /
• 2021

This study investigated the overall dependence of the tensile properties of Al-Si alloys on the distribution aspect of a eutectic Si particle in terms of defect susceptibility to the effective void area fraction, referring to the sum of pre-existing microvoids and the damage evolution of the Si particle. The network morphology of as-cast Al-xSi (x=2,5,8,11) alloys was modified to a granular type via a T4 treatment, after which a computational topography (CT) analysis and scanning electron microscope (SEM) observations were utilized to evaluate the size and distribution of the microvoids. The CT and SEM analyses indicated that the main cracks grow along local regions that possess the highest porosity level. The local plastic deformation around the microvoids and the distribution aspect of the microvoids induced a practical difference between the iso-volumetric CT measurement and the SEM fractography outcomes. The results demonstrated that the overall dependence of the ultimate tensile strength (UTS) and elongation on the effective void area fraction is more sensitive to the variation of the area fraction of the Si particle in the network morphology than in the granular type; this is due to the sequential damage evolution of the neighboring Si particles in the eutectic Si colony.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.3
• /
• pp.351-357
• /
• 2001

The rapid formation of a cream line cannot be observed in raw goat's milk standing at a low temperature. Although the poor creaming ability of goat's milk has been considered to be due to the small size of milk fat globules and the lack of euglobulin capable of being adsorbed on milk fat globules, there is much left to study. The present work attempted to elucidate a factor for poor creaming ability of goat's milk. The creaming ability of the experimental milks reconstituted from creams and skim milks separated from cow's milk or goat's milk was measured by the volume of the cream layer and the fat content of bottom layer. The polypeptides composition of the P1 the fraction (i.e., the high molecular weight fraction eluted near the void volume obtained by the gel filtration of whey) and milk fat globule membrane prepared from both milks were compared. It was found that the promotion of creaming originated from goat's skim milk was lower than that from cow's skim milk. The P1 fraction in goat's skim milk was less than that in cow's skim milk. The polypeptide (M.W. $4.3{\times}10^4$), found in the P1 fraction of cow's milk was not found in the P1 fraction of goat's milk. It is suggested that the poor creaming ability of goat milk is caused mainly by the difference from cow milk in the amount and the composition of the P1 fraction.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.129-137
• /
• 2017

In this study, the prediction of landslide probability was performed to the study area located in ${\bigcirc}{\bigcirc}$ area of Muan-gun, Jeonnam Province around Honam railway using the computer program SHAPP ver 1.0 developed by a decision tree model. The soil samples were collected at total 8 points, and soil tests were performed to measure soil properties. The thematic maps of soil properties such as coefficient of permeability and void ratio were made on the basis of soil test results. The slope angle analysis of topography was performed using a digital map. As the prediction result of landslide probability, 435 cells among total 15,552 cells were predicted to be in the event of landslides. Therefore, the predicted area of occurring landslides may be $43,500m^2$ because the analyzed cell size was $10m{\times}10m$.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.57-66
• /
• 2017

Self-weight consolidation test and soil property of dredged soil at Incheon habour route were analyzed to determine the initial dredging reclamation amount, reclamation depth, and estimating the required time of self-weight consolidation with calculation of the final planned height of dredging reclamation site. The moisture content, void ratio and ratio of volume change with elapsed time after throwing were estimated through Yano's empirical equation. As a result, there was a less variation in elements when fine-grained soil content was low as similarly to the behavior of coefficient of sedimentation-consolidation, Cs and the highest variation was shown at the fine-grained soil content of 50%. The retention ratio according to the fine grained soil content that could reinforce the comprehensive aspect of retention ratio for each particle size presented in the standard of estimate for reclamation construction work was calculated and presented using the calculated ratio of volume change.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.2
• /
• pp.1-14
• /
• 2009

Ductility-based seismic design is strongly required for the rational and cost-effective design of RC piers, and a reliable evaluation of shear strength is indispensable for its success. Unlike the flexural behavior of RC columns, shear behavior is highly complex, due to its many effects such as size, aspect ratio, axial force, ductility and so on. To address this, many design and empirical equations have been proposed considering these effects. However, these equations show significant differences in their evaluation of the initial shear strength, and the reduction in strength with the increase of ductility. In this study, the characteristics of initial shear strength of hollow sectional columns were investigated using experiments with the parameters of aspect ratios, void ratios, web area ratios and load patterns. The test results were analyzed through a comparison with the values predicted by empirical equations. On the basis of the mechanical characteristics and test results, a new empirical equation was proposed, and its validity was assessed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1392-1401
• /
• 2017

In this study, the design methodology of pattern classification is introduced for avoiding faults through partial discharge occurring in the power facilities and local sites. In order to classify some partial discharge types according to the characteristics of each feature, the model is constructed by using the Radial Basis Function Neural Networks(RBFNNs) and Particle Swarm Optimization(PSO). In the input layer of the RBFNNs, the feature vector is searched and the dimension is reduced through Principal Component Analysis(PCA) and PSO. In the hidden layer, the fuzzy coefficients of the fuzzy clustering method(FCM) are tuned using PSO. Raw datasets for partial discharge are obtained through the Motor Insulation Monitoring System(MIMS) instrument using an Epoxy Mica Coupling(EMC) sensor. The preprocessed datasets for partial discharge are acquired through the Phase Resolved Partial Discharge Analysis(PRPDA) preprocessing algorithm to obtain partial discharge types such as void, corona, surface, and slot discharges. Also, when the amplitude size is considered as two types of both the maximum value and the average value in the process for extracting the preprocessed datasets, two different kinds of feature datasets are produced. In this study, the classification ratio between the proposed RBFNNs model and other classifiers is shown by using the two different kinds of feature datasets, and also we demonstrate the proposed model shows superiority from the viewpoint of classification performance.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.193-196
• /
• 2011

Lead zirconate titanate (PZT)/ bismuth ferrite (BFO) multilayer thin films have been fabricated by the spin-coating method on Pt(200 nm)/Ti(10 nm)/$SiO_2$(100 nm)/p-Si(100) substrates using $BiFeO_3$ and $Pb(Zr_{0.52}Ti_{0.48})O_3$ metal alkoxide solutions. The PZT/BFO multilayer thin films show a uniform and void-free grain structure, and the grain size is smaller than that of PZT single films. The reason for this is assumed to be that the lower BFO layers play an important role as a nucleation site or seed layer for the formation of homogeneous and uniform upper PZT layers. The dielectric constant and dielectric losses decreased with increasing number of coatings, and the six-layer PZT/BFO thin film has good properties of 162 (dielectric constant) and 0.017 (dielectric losses) at 1 kHz. The remnant polarization and coercive field of three-layer PZT/BFO thin films were 13.86 ${\mu}C/cm^2$ and 37 kV/cm respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.302-317
• /
• 1995

After initial structure of AISI 9260 steel is changed into pearlite and martensite, one is isothermally annealed at $700^{\circ}C$ below of $A_1$ transformation point and the other is isothermally annealed at the same condition after 3 cycles of heating and cooling between $680^{\circ}C$ and $780^{\circ}C$ of $A_1$ transformation point. Analyzing the changes of microstructure, mechanical properties and fractography of tension test, we obtained result as follows. The fastest spheroidization rate by changes of initial structure and heat treatment cycles is appeared at the heat treatment cycle which is isothermally annealed after 3 cycles of heating and cooling at below and above $A_1$ transformation point for martensite. At the above condition, the perfect spheroidization structure is appeared after 60hrs and after then, globular carbide is being coarsened. The mean diameter of globular carbide is $2.4{\times}10^{-3}mm$ after 90hrs. The changes of tension strength during spheroidization heat treatment follows Orwan function, ${\sigma}_o={\sigma}_i+Gb/l$, where l is interspacing of carbide particles and at the above condition, ${\sigma}_o=70.48+2.5{\times}10^{-3}/l(kg/mm^2)$. Fractography of fracture of spheroidization structure in tension test is appeared as dimple which is ductile rupture type by nucleation and growth of void, size of dimple is larger and deeper with increasing of heat treatment time.

• The Research Journal of the Costume Culture
• /
• v.28 no.1
• /
• pp.15-29
• /
• 2020

Purpose of the study is to explore the effect of the types of mobile coupons(text- vs. image-focused coupons; free-gift vs. discount coupons) on characteristic perception of mobile coupons, and the causal relationships among characteristic perception, attitude, and use intention of mobile coupons. A total of 140 university students participated in experiments with questionnaires including one of the four stimuli. Important findings are as follows. First, image-focused mobile coupons generated more enjoyment than did text-focused coupons. However, the text/image-focused coupons were not different in perception of informativeness and credibility of mobile coupons. Second, enjoyment perception was significantly increased when image-focused contents were combined with discount coupons whereas enjoyment perception was decreased when text-focused contents were combined with free-gift coupons. This interaction effect reflects that the level of enjoyment of consumers can be changed in terms of the combination of the value-provision types of coupons and the text-image focused contents. Third, it was found that consumer perception of coupon characteristics formed attitudes toward mobile coupons, and use intention of mobile coupons was determined by attitudes toward mobile coupons. Study findings may fill the void of research investigating the effect of text-image contents and the types of coupons on consumer reponses toward mobile coupons. Mobile coupons have limited quantity of information within a small size of mobile phone screen, therefore, the results were not consistent with prior research tested with mobile advertisements indicating the effect of text-image contents on perception of informativeness and credibility.

• Composites Research
• /
• v.29 no.5
• /
• pp.315-320
• /
• 2016

Conventionally, composite aircraft structures are fabricated within autoclave at high pressure. However, autoclave process has several disadvantages including high curing costs and limitation of part size. Recently, out-of-autoclave (OoA) processes have been investigated in many studies to replace conventional autoclave process. A newly developed OoA prepreg, using conventional ovens, can significantly reduce the curing costs and produce autoclave-quality parts. Nevertheless, manufacture of void-free complex shape structure using OoA process presents significant challenges because of the low consolidation pressure. In this study, integrated skin-spar-rib composite part was fabricated using OoA prepreg. And cross-sectional macro- and micro-graphs of the part were examined in order to assess the possibility of replacing conventional autoclave process.