• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.2
• /
• pp.74-84
• /
• 2016

After installing roundabouts, changes of travel behaviour in the vicinity of roundabouts can cause increasing traffic volumes and unbalanced flow conditions. In that cases, the efficiency of roundabouts as a whole intersections can drop due to the insufficient gap between vehicles in the circulating lanes. The purpose of this study is developing a dynamic signal metering operation method for roundabouts in which a real time Signal Metering operation algorithm is suggested and its performance is tested by using VISSIM COM Interface(Visual Basic Application). The results of the real time Signal Metering operation show that there is a substantial delay improvements when two adjoined approaches are combined together and the flows of metering approach are less than controlling approach. Especially, the total entering flow is around 1,600 vehicle/h gives the delay reduction per vehicle of 70.9~102.2(73.8~77.8%) seconds for four-lane-approach with one-lane roundabouts.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.4
• /
• pp.54-62
• /
• 2018

As a part of realization of artificial intelligence signal(AI Signal), this study proposed an actuated signal algorithm based on vehicle queue length that estimates in real time by deep learning. In order to implement the algorithm, we built an API(COM Interface) to control the micro traffic simulator Vissim in the tensorflow that implements the deep learning model. In Vissim, when the link travel time and the traffic volume collected by signal cycle are transferred to the tensorflow, the vehicle queue length is estimated by the deep learning model. The signal time is calculated based on the vehicle queue length, and the simulation is performed by adjusting the signaling inside Vissim. The algorithm developed in this study is analyzed that the vehicle delay is reduced by about 5% compared to the current TOD mode. It is applied to only one intersection in the network and its effect is limited. Future study is proposed to expand the space such as corridor control or network control using this algorithm.

• The Journal of the Korea Contents Association
• /
• v.18 no.3
• /
• pp.52-61
• /
• 2018

This research suggested the traffic signal timing calculation model for signal intersections based on sectional travel time. A detection system that collects sectional travel time data such as Urban Transport Information System(UTIS) is applied. This research developed the model to calculate saturation flow rate and demand volume from travel time information using a deterministic delay model. Moreover, this model could determine the traffic signal timings to minimize a delay based on Webster model using traffic demand volume. In micro simulation analysis using VISSIM and its API ComInterface, it checked the saturation conditions and determined the traffic signal timings to minimize the intersection delay. Recently, sectional vehicle detection systems are being installed in various projects, such as Urban Transportation Information System(UTIS) and Advanced Transportation Management System(ATMS) in Korea. This research has important contribution to apply the traffic information system to traffic signal operation sector.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.3
• /
• pp.84-94
• /
• 2019

This paper developed the VSL control algorithms for various traffic conditions in tunnels. Various algorithms determining control speed, buffer speed, and display time were suggested in order to apply three gantry locations. The algorithms were evaluated by constructing simulation environments using python and VISSIM Com-Interface. Results show that speed difference between congested flow and normal flow was 50 km/h without algorithm application, but the difference was reduced to 20 km/h with algorithm application. In addition, the length of congested region in the exit section of the tunnel was also reduced from 800m to 300m with algorithm application. It is expected that the traffic accidents in tunnels may be reduced since the average and standard deviation of the speed are greatly reduced after applying the algorithms suggested.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.897-905
• /
• 2015

This research suggested the traffic signal calculation model of active transit signal priority using a shockwave model. Using this signal priority timing optimization model, the shockwave area is computed under the condition of Early Green and Green Extension among active transit signal priority techniques. This study suggested the speed estimation method of backward shockwave using average travel time and intersection passing time. A shockwave area change is calculated according to signal timing change of transit signal priority. Moreover, this signal timing calculation model could determine the optimal signal priority timings to minimize intersection delay of general vehicles. A micro simulation analysis using VISSIM and its user application model ComInterface was applied. This study checked that this model could calculate the signal timings to minimize intersection delay considering saturation condition of traffic flow. In case studies using an isolated intersection, this study checked that this model could improve general vehicle delay of more over ten percentage as compared with equality reduction strategy of non-priority phases. Recently, transit priority facilities are spreading such as tram, BRT and median bus lane in Korea. This research has an important significance in that the proposed priority model is a new methodology that improve operation efficiency of signal intersection.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.133-143
• /
• 2018

Roundabouts are generally installed at which traffic and pedestrian volume is relatively small intersections, and hence traffic can flow one direction around a circular island without traffic lights. A number of researches for roundabout signal metering have been processing ways to deal with operation efficiency drops in conditions of unusual traffic and pedestrian volume increases. However, there is still a shortcoming exists in previous operation algorithm does not consider the hidden vehicles between yield lines and detectors and queueing vehicles in circular lanes. These queueing vehicles between them can be cleared by introducing the queue clearance time. The purpose of this research is developing a real time signal metering operation algorithm by considering the vehicle queue clearance time. The results of varying queue clearance time application show that there is a substantial average vehicle delay reduction in VISSIM Com-Interface simulation. When the total number of entering vehicle is 3,200~4,800 vehicle/hour with varying queue clearance time application 21~50 seconds gives average delay reduction per vehicle by 16.1~71.7%.

• Journal of Korean Society of Transportation
• /
• v.34 no.1
• /
• pp.68-80
• /
• 2016

Interest in freeway truck traffic has increased largely due to greater safety concerns regarding truck-related crashes. The negative interactions between slow-moving trucks and other vehicles are a primary cause of hazardous conditions, which lead to crashes with larger speed variations. To improve operational efficiency and safety, providing a climbing lane that separates slow-moving trucks from higher performance vehicles is frequently considered when upgrading geometrics. This study developed an operations strategy for freeway climbing lanes based on traffic conditions in real time. To consider traffic safety when designing a dynamic strategy to determine whether a climbing lane is closed or open, various factors, including the level of service (LOS) and the percentage of trucks, are investigated through microscopic simulations. A microscopic traffic simulator, VISSIM, was used to simulate freeway traffic streams and collect vehicle-maneuvering data. Additionally, an external application program interface, VISSIM's COM-interface, was used to implement the proposed climbing lane operations strategies. Surrogate safety measures (SSM), including the frequency of rear-end conflicts and, were used to quantitatively evaluate the traffic safety using an analysis of individual vehicle trajectories obtained from VISSIM simulations with various operations scenarios. It is expected that the proposed algorithm can be the backbone for operating the climbing lane in real time for safer traffic management.

• Journal of Korean Society of Transportation
• /
• v.28 no.4
• /
• pp.167-175
• /
• 2010

The ubiquitous transportation system environments make it possible to collect each vehicle's position and velocity data and to perform more sophisticated traffic flow management at the individual vehicle or platoon level through vehicle to vehicle (V2V) and vehicle to infrastructure (V2I) communication. It is necessary to develop a traffic flow management scheme to take advantage of the ubiquitous transportation system environments. This paper proposes an algorithm to advise the optimal speed for each vehicle according to the traffic flow condition. The algorithm aims to stabilize the traffic flow by advising the equilibrium speed to the vehicles speeding or crawling under freely flowing condition. And it aims to prevent or at least alleviate the shockwave propagation by advising the optimal speed that should dampen the speed drop under critical flow conditions. This paper builds a simulation testbed and performs some simulation experiments for the proposed algorithm. The proposed algorithm shows the expected results in terms of travel time reduction and congestion alleviation.