• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.960-968
• /
• 2012

In this study, the measurement of physical properties of 3 different ethylene oxide adducted zwitterionic surfactants were measured such as critical micelle concentration, surface tension, interfacial tension, contact angle, viscosity and foam stability. Also, the dual function characteristics of the zwitterionic surfactants were investigated by determining an isoelectric point, which were obtained using zeta potential measurement and QCM (quartz crystal microbalance) experiments. The isoelectric point of the synthesized zwitterionic surfactant determined by zeta potential measurement was close to that obtained by QCM experiment and both results have shown almost the same trend as that determined by the frictional property measured using an automated mildness tester. In particular, it has been observed that all three surfactants used during this study provide better softening effect at a pH of neutral condition than at an acidic or an alkaline condition. This result indicates that the synthesized surfactants act as a cationic surfactant at a pH of neutral condition and thus provide good softening effect during a rinsing cycle in the detergency process.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.132-139
• /
• 2005

Sintering behavior of $BaO-Nd_{2}O_3-TiO_2$ with a Pb-based glassceramics frit were investigated in order to understand an effect of glassceramics as a low temperature sintering agent on dielectric ceramics. A green sheet form was fabricated through tape casting method with the glassceramic fut added $BaO-Nd_{2}O_3-TiO_2$. The dispersion properties, rheological properties and final density of dielectric composit slurry as a function of amount and composition of organic additives was examined. The dispersants' addition was effective in controlling dispersion of the ceramics in solution. The addition of excessive dispersant showed adverse effect on dispersion. The prepared slurries, containing ceramic : powders, glass-ceramics and various kinds of organic viechles, exhibited typical shear thinning behavior. The best properties of tape casting appeared powder to solvent ratio 65 : 35 and amount of the binder 6 wt$\%$ and plasticizer 3 wt$\%$. The viscosity of the slurry was 677 cps and green/sintered density in the tape was $3.3 g/cm^3,\;5.56 g/cm^3$ respectively.

• KSBB Journal
• /
• v.11 no.5
• /
• pp.565-571
• /
• 1996

Medium optimization for ${\beta}$-mannanase production by Aspergillus oryzae ATCC 2114 was performed. Effect of carbon source (locust bean gum) concentration on ${\beta}$-mannanase production was investigated. Above 20 g/L locust bean gum, a lag time for ${\beta}$-mannanase production was appeared because high concentration of locust bean gum caused high viscosity which made the mixing of medium poor. As the locust bean gum concentration in the medium increased, ${\beta}$-mannanase activity and cell growth increased proportionally. Effect of various nitrogen sources on ${\beta}$-mannanase production was also studied. (NH4)2SO4 and malt extract were the most effective for ${\beta}$-mannanase production among the inorganic nitrogenous compounds and organic nitrogen nutrients. Inorganic compounds such as KH2SO4, NaCl, Na2CO3, and MgSO4, on ${\beta}$-mannanase production were optimized for ${\beta}$-mannanase production. Locust bean gum of 10 g/L, malt extract of 3 g/L, (NH4)2SO4 of 2 g/L, KH2SO4, of 10 g/L were selected as the optimal medium. Culture in a fermentor by using the optimal medium was carried out. Lag time of ${\beta}$-mannanase production was shorter due to the better mixing of the fermentor. The maximum ${\beta}$- mannanase activity of 9.7 unit/mL and specific ${\beta}$-mannanase activity of 1.9 unit/mg-cell could be obtained at 27 hours and the productivity of ${\beta}$-mannanase was 0.36 unit/mL$.$h.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.1
• /
• pp.50-57
• /
• 2011

This study examined the effect of gamma irradiation (3-20 kGy) on the immune activity and physicochemical properties of Myagropsis myagroides (MM) water extracts. MM powder and water extracts were subjected to gamma irradiation at 3, 7, and 20 kGy. The effects of gamma-irradiated MM water extracts on splenocyte proliferation and cytokine IFN-${\gamma}$ and IL-2 secretion were evaluated. The gamma-irradiated MM water extracts resulted in decreased splenocyte proliferation without cytotoxicity. The IFN-${\gamma}$ and IL-2 secretion increased by gamma-irradiated MM water extracts with increasing irradiation dose. For MM powder, the yield and total phenolic compounds (TPC) of water extracts were increased slightly after gamma irradiation. In MM water extracts, the TPC was higher at a dose of 20 kGy, while gamma irradiation decreased the viscosity, pH, and color of the MM extracts. In conclusion, gamma irradiation improved the immunomodulatory activity of MM water extracts, overcoming its potential weakness when applied in the food industry.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.71-77
• /
• 2001

Unsaturated polyester(UP) resin is one of the major thermosetting resins. It is very useful as the matrix resin of the composite material because of its low viscosity. The polymer resin, however, has several drawbacks; The volume shrinkage occurs during the crosslinking reaction of the UP resin with styrene monomer and the resulting polymer is weak to the alkali and also brittle. The mechanical properties of UP resin can be improved by blending various materials. In this study, polyurethane(PU) was used as a modifier in order to enhance the toughness of the UP resin. The goal of the research is to study the effect of the polyol molecular weight as a PU soft segment and the PU contents on the toughness of PU-modified UP resins. UP/PU polymer network may occur through the reaction between isocyanate group in the methyldiisocyanate(MDI) and hydroxyl group in the UP molecules. The maximum toughness value was shown at 2 wt% of the PU content. This effect results from the incorporation of the PU segment into the UP resin.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.451-458
• /
• 2002

Osteoporosis is a systemic skeletal disease caused by low bone mass and the decrease of bone density in the microstructure of trabecular bone. Drug therapy(PTH Parathyroid hormone) may increase the trabecular thickness and thus bone strength. Vertebroplasty is a minimally invasive surgery foy the treatment of osteoporotic vertebral compression fracture. This Procedure includes Puncturing vertebrae and filling with Polymethylmethacrylate(PMMA). Although altering recommended monomer-to-Powder ratio affects material properties of bone cement, clinicians commonly alter the mixture ratio to decrease viscosity and increase the working time. The Purposes of this study were to analyze the effect of 4he monomer-to-powder ratio on the mechanical characteristics of trabecular. In this paper, the finite element model of human vertebral trabecualr bone was developed by modified Voronoi diagram, to analyze the relative effect of hormone therapy and vertebroplasty at the treatment of osteoporotic vertebrae. Trabeuclar bone models for vertebroplasty with varied monomer-to-Powder ratio(0.40∼1.07 ㎖/g) were analyzed. Effective modulus and strength of bone cement-treated models were approximately 60% of those of intact models and these are almost twice the values of hormone-treated models. The bone cement models with the ratio of 0.53㎖/g have the maximum modulus and strength. For the ratio of 1.07㎖/g, the modulus and strength were minimum(42% and 49% respectively) but these were greater than those for drug therapy. This study shows that bone cement treatment is more effective than drug therapy. It is found that in vertebroplasty, using a monomer-to-powder ratio different from that recommended by manufacturer nay significantly not only reduce the cement's material Properties but also deteriorate the mechanical characteristics of osteoporotic vertebrae.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.112-118
• /
• 2012

In this study, physical properties of synthesized DE7-OSA82-AO and DEP52-OSA82-AOQ82 zwitterionic surfactants were measured such as critical micelle concentration, surface tension, interfacial tension, contact angle and viscosity. Phase behavior study was also performed. The dual function characteristics of a zwitterionic surfactant were investigated by determining an isoelectric point, which was attained using zeta potential measurements and QCM (quartz crystal microbalance) experiments. The isoelectric point of DE7-OSA82-AO surfactant determined by the zeta potential measurement and QCM experiment was about 7.2 and 7.4, respectively. On the other hand, the isoelectric point of DEP52-OSA82-AOQ82 surfactant determined by the zeta potential measurement and QCM experiment was about 10.9 and 11.0, respectively. The frictional property measured using an automated mildness tester showed that DE7-OSA82-AO surfactant can provide a good softening effect at an acidic or neutral condition. On the other hand, DEP52-OSA82-AOQ82 was found to provide a good softening effect to a fabric surface at a pH below its isoelectric point of 11.

• Food Science and Preservation
• /
• v.22 no.3
• /
• pp.408-420
• /
• 2015

This study investigated the effect of heat treatment conditions on the quality and antioxidant activities of Korean traditional actinidia (Actinidia arguta) cultivars puree. Heat treatment on actinidia puree was conducted at $70{\sim}90^{\circ}C$ for 1 min to 5 mins, while a control sample of the actinidia puree was prepared without heat treatment. In all the samples, except for the sample treated at $90^{\circ}C$ for 5 mins, pH and Brix degree was not dramatically changed. Pulp content decreased with increasing temperature and time. L and the a value of color increased with increasing temperature and time. However, the b value showed a reverse tendency with L and the a value. Viscosity and gumminess increased as heat temperature and time increased, though cohesiveness was not significantly changed depending on temperature and time. Coliform and yeast were not detected on all samples and the number of aerobic bacteria and mold decreased as temperature and time increased. Vitamin C and total phenolic content of the puree was not changed for 1, 3, and 5 mins at $70^{\circ}C$ and for 1 and 3 mins at $80^{\circ}C$, but significantly decreased with increasing time at $90^{\circ}C$. Furthermore, the antioxidant activities of the puree, such as DPPH radical scavenging activity, ABTS radical scavenging activity, and FRAP (ferric reducing antioxidant power) showed a similar tendency with total phenolic content.

• Corrosion Science and Technology
• /
• v.9 no.4
• /
• pp.147-152
• /
• 2010

Conventional paints for conversion coating applications in steel production derived mainly from water-based polymer dispersions containing several additives actually show good general performance, but suffer from poor scratch and abrasion resistance during use. The reason for this is because the relatively soft organic binder matrix dominates the mechanical surface properties. In order to maintain the high quality and decorative function of coated steel sheets, the mechanical performance of the surface needs to be improved significantly. In fact the wear resistance should be enhanced without affecting the optical appearance of the coatings by using appropriate nanoparticulate additives. In this direction, nanocomposite coating compositions (Nanomer$^{(R)}$) have been derived from water-based polymer dispersions with an increasing amount of surface-modified nanoparticles in aqueous dispersion in order to monitor the effect of degree of filling with rigid nanoparticles. The surface of nanoparticles has been modified for optimum compatibility with the polymer matrix in order to achieve homogeneous nanoparticle dispersion over the matrix. This approach has been extended in such a way that a more expanded hybrid network has been condensed on the nanoparticle surface by a hydrolytic condensation reaction in addition to the quasi-monolayer type small molecular surface modification. It was expected that this additional modification will lead to more intensive cross-linking in coating systems resulting in further improved scratch-resistance compared to simple addition of nanoparticles with quasi-monolayer surface modification. The resulting compositions have been coated on zinc-galvanized steel and cured. The wear resistance and the corrosion protection of the modified coating systems have been tested in dependence on the compositional change, the type of surface modification as well as the mixing conditions with different shear forces. It has been found out that for loading levels up to 50 wt.-% nanoparticles, the mechanical wear resistance remains almost unaffected compared to the unmodified resin. In addition, the corrosion resistance remained unaffected even after $180^{\circ}$ bending test showing that the flexibility of coating was not decreased by nanoparticle addition. Electron microscopy showed that the inorganic nanoparticles do not penetrate into the organic resin droplets during the mixing process but rather formed agglomerates outside the polymer droplet phase resulting in quite moderate cross linking while curing, because of viscosity. The proposed mechanisms of composite formation and cross linking could explain the poor effect regarding improvement of mechanical wear resistance and help to set up new synthesis strategies for improved nanocomposite morphologies, which should provide increased wear resistance.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.566-572
• /
• 2014

Maleic anhydride (MAH) grafted polypropylenes (PP) (MAH-g-PP) were prepared by changing MAH content and styrene monomer (SM)/MAH mole ratio with different type PP, using a twin screw extruder. The types of PP were isotatic PP (iPP), block PP (bPP), and random PP (rPP) and dicumyl peroxide (DCP) was used as an initiator. The graft degree of MAH was confirmed by the existence of carbonyl group (C=O) stretching peak at $3100cm^{-1}$ of FTIR spectrum. Thermal properties of MAH-g-PP and PP/MAH-g-PP/pulp composites were investigated by DSC and TGA. There was no district change in thermal properties of PP/MAH-g-PP/pulp composites. Based on tensile properties and SEM pictures for fractured surface of PP/MAH-g-PP/pulp composites, MAH-g-rPP was the best as the compatibilizer and optimum formulation was MAH content of 1.0 wt%, SM/MAH mole ratio of 1.0, and melt index (MI) of 25 g/10 min. The rheological properties of the composites were investigated by a dynamic rheometer. The complex viscosity, shear thinning effect, and water uptake incresed with pulp content.