• 제목/요약/키워드: Vickers Hardness

검색결과 677건 처리시간 0.021초

Electrodeposition법으로 제조한 Ni-Fe 나노박막 및 나노선의 특성에 미치는 용액 조성의 영향 (Effect of Solution Compositions on Properties of Ni-Fe Nano Thin Film and Wire Made by Electrodeposition Method)

  • 구본급
    • 한국표면공학회지
    • /
    • 제43권5호
    • /
    • pp.243-247
    • /
    • 2010
  • The micro Vickers hardness and internal stress of Ni-Fe metal thin film synthesized by electrodeposition method at $25^{\circ}C$ were studied as a function of bath composition, and surface microstructure and atomic compositions of thin films were investigated by SEM and EDS. And the shape change of $200\;{\AA}$ Ni-Fe nanowires made using anodic aluminum oxide(AAO) templates by electrodeposition method were observed by SEM as a function of ultrasonic treatment time and bath composition. The Fe deposition contents on the substrate non-linearly increased with Fe ion concentration over total metal ion concentration. In case of low Fe contents film, the grain size is smaller and denser than high Fe contents deposited films, and the micro Vickers hardness increased with Fe contents of electrodeposited films. These results affected the shape change of nanowire after ultrasonic treatments.

무연 Sn-Ag-Bi-Ga계 솔더의 특성에 관한 연구 (A Study on the Characteristic of Pb-free Sn-Ag-Bi-Ga Solder Alloys)

  • 노보인;이보영
    • Journal of Welding and Joining
    • /
    • 제18권6호
    • /
    • pp.42-47
    • /
    • 2000
  • The object of this study is to estimate Sn-Ag-Bi-Ga solder alloy as a substitute for Sn-37Pb alloy. For Sn-Ag-Bi-Ga alloys, Ag, Bi and Ga contents are varied. (Ag : 1~5%, Ga : 3%, Bi : 3~6%) Comparing to Sn-37Pb alloy Sn-Ag-Bi-Ga alloys have wider melting temperature range up to max. $18.7^{\circ}C$. With increasing Ag, Bi contents, the wettability of the alloys increased up to max. 6.6 mN. The vickers hardness of the alloys was max. 46.4 Hv. The ultimate tensile stress of the alloys was max. 60.3 MPa and the elongation was max. 1.2%. The joint strength between circuit board and solder was max. 55.5 N and the joint strength between connector and solder was max. 176.1 N. There were no cracks in this alloys after thermal shock test.

  • PDF

세라미스 파괴인성평가에 있어서 IF법과 AE (Acoustic Emission and Indentation Fracture Method for the Engineering Ceramics)

  • 김부안;문창권
    • 한국해양공학회지
    • /
    • 제15권2호
    • /
    • pp.61-65
    • /
    • 2001
  • The fracture toughness of ceramics can be measure by such various methods as DT (double torsion), CN (chevron notch) etc. But, the application of these methods to the engineering ceramics is very difficult because of its very high hardness. So, IF (indentation fracture) method is generally used for the evaluation of fracture toughness of ceramics. The Median crack induced by the sharp Vickers indenter was compared with the detected AE (acoustic emission) signal. On the silicon nitride ceramics, the AE test results agree fairly well with the median crack occurance and growth process. But, on the alumina, very many complicated crack signals were detected besides median crack. It can be considered that the IF methods must be used in limited engineering ceramics materials.

  • PDF

HV가 다른 0.57 wt.% 탄소강의 미소 균열에 따르는 피로 한도 (Fatigue Limit According to Microcracks in 0.57 wt.% Carbon Steel with Different HV)

  • 오창석;구경희;이금화;남기우
    • 한국산업융합학회 논문집
    • /
    • 제25권2_2호
    • /
    • pp.233-238
    • /
    • 2022
  • This study evaluated the fatigue limit depending on microcracks using 0.57 wt.% carbon steel with different Vickers hardness. The fatigue limit was almost constant up to a certain limit regardless of the carbon content. However, the fatigue limit decreased rapidly as the size of the crack increased. As the crack aspect ratio was smaller, the fatigue limit of the depth (point A) a lot decreased. The fatigue limit ratio of the depth decreased significantly because the crack propagation in the depth direction was fast as the crack aspect ratio became smaller. On the other hand, the fatigue limit ratio of surface cracks increased as the crack aspect ratio decreased.

Mechanical performance of additively manufactured austenitic 316L stainless steel

  • Kim, Kyu-Tae
    • Nuclear Engineering and Technology
    • /
    • 제54권1호
    • /
    • pp.244-254
    • /
    • 2022
  • For tensile tests, Vickers hardness tests and microstructure tests, plate-type and box-type specimens of austenitic 316L stainless steels were produced by a conventional machining (CM) process as well as two additive manufacturing processes such as direct metal laser sintering (DMLS) and direct metal tooling (DMT). The specimens were irradiated up to a fast neutron fluence of 3.3 × 109 n/cm2 at a neutron irradiation facility. Mechanical performance of the unirradiated and irradiated specimens were investigated at room temperature and 300 ℃, respectively. The tensile strengths of the DMLS, DMT and CM 316L specimens are in descending order but the elongations are in reverse order, regardless of irradiation and temperature. The ratio of Vickers hardness to ultimate tensile strength was derived to be between 3.21 and 4.01. The additive manufacturing processes exhibit suitable mechanical performance, comparing the tensile strengths and elongations of the conventional machining process.

Inhibitory effect on Streptococcus mutans and mechanical properties of the chitosan containing composite resin

  • Kim, Ji-Sun;Shin, Dong-Hoon
    • Restorative Dentistry and Endodontics
    • /
    • 제38권1호
    • /
    • pp.36-42
    • /
    • 2013
  • Objectives: This study evaluated the antibacterial effect and mechanical properties of composite resins ($L_{CR}$, $M_{CR}$, $H_{CR}$) incorporating chitosan with three different molecular weights (L, Low; M, Medium; H, High). Materials and Methods: Streptococcus (S). mutans 100 mL and each chitosan powder were inoculated in sterilized 10 mL Brain-Heart Infusion (BHI) solution, and was centrifuged for 12 hr. Absorbance of the supernatent was measured at $OD_{660}$ to estimate the antibacterial activities of chitosan. After S. mutans was inoculated in the disc shaped chitosan-containing composite resins, the disc was cleansed with BHI and diluted with serial dilution method. S. mutans was spread on Mitis-salivarius bacitracin agar. After then, colony forming unit (CFU) was measured to verify the inhibitory effect on S. mutans biofilm. To ascertain the effect on the mechanical properties of composite resin, 3-point bending and Vickers hardness tests were done after 1 and 3 wk water storage, respectively. Using 2-way analysis of variance (ANOVA) and Scheffe test, statistical analysis was done with 95% significance level. Results: All chitosan powder showed inhibition effect against S. mutans. CFU number in chitosan-containing composite resins was smaller than that of control resin without chitosan. The chitosan containing composite resins did not show any significant difference in flexural strength and Vickers hardness in comparison with the control resin. However, the composite resin, $M_{CR}$ showed a slightly decreased flexural strength and the maximum load than those of control and the other composite resins $H_{CR}$ and $L_{CR}$. Conclusions: $L_{CR}$ and $H_{CR}$ would be recommended as a feasible antibacterial restorative due to its antibacterial nature and mechanical properties.

12%-Cr 강의 $CO_2$ 레이저 표면경화에서 금속조직과 경도분포 (Microstructure and Hardness Distributions of $CO_2$ Lser Hrdened 12%-Cr Seel)

  • 김재도
    • 대한기계학회논문집
    • /
    • 제16권10호
    • /
    • pp.1861-1868
    • /
    • 1992
  • 본 연구에서는 발전소의 터빈 블레이드는 물방울에 의해서 부식이 발생한다는 사실은 널리 알려져 있다. 부식을 방지하기위해서 보통 12%-Cr 강으로 만들며 표면 을 고주파 유도경화법에 의해서 표면을 경화시킨다. 고주파유도 경화법은 경화층 깊 이가 마모 특성을 가장 좋게 하는 깊이보다 훨씬 깊게 경화되며, 열응력이 과대하게 생기고, 처리시간이 많이 걸리며, 표면경화 처리후 기계가공이 필요하다. 12%-Cr 강 의 레이저 표면경화를 연속파 3kw CO$_{2}$ 레이저로 실험하여 금속조직과 경도분포에 대해서 연구하여 레이저 표면경화 가능성을 고찰하였다.

Chlorhexidine varnish가 법랑질의 탈회예방에 미치는 영향 (THE PREVENTIVE EFFECT OF CHLORHEXIDINE VARNISH ON ENAMEL DEMINERALIZATION)

  • 임은경;최영철
    • 대한소아치과학회지
    • /
    • 제25권4호
    • /
    • pp.825-836
    • /
    • 1998
  • The intention of this study was to investigate the preventive effect of chlorhexidine varnish on enamel demineralization. The sample consisted of 57 first premolars scheduled to be extracted for orthodontic purposes. The control group (N=10) was left untreated and the experimental groups were worn with specially designed stainless steel orthodontic bands on premolar for plaque accumulation. The group 1 (N=9) was worn band only, the group 2 (N=19) was applied with chlorhexidine varnish for one time, and the group 3 (N=19) was applied with chlorhexidine varnish for 3 times once a week. After 4 weeks of experimental periods, every specimen were examined by SEM and Vickers hardness test to evaluate and compare the degree of enamel decalcification. The results were as follows: 1. Although SEM revealed various degree of enamel demineralization in every experimental groups, the group 1 showed more severe demineralizations than the group 2 and 3. 2. The mean Vickers Hardness Numbers measured in this study seemed to reveal that there was a statistically significant difference between the control goup and the group 1 (P<0.05), and also a significant difference between the group 1 and the group 2, 3 (P<0.05). And there was no significant difference between the group 2 and the group 3 (p>0.05). 3. The results of VHN did not deemed to show a statistically significant difference between maxillary premolar and mandibular premolar in both group 2 and group 3 (P>0.05).

  • PDF

타이타늄합금의 전자빔용접성 (Electron beam weldability of titanium alloy)

  • 이채훈;윤종원;박노광
    • 한국레이저가공학회지
    • /
    • 제10권4호
    • /
    • pp.13-17
    • /
    • 2007
  • Electron beam weldability was investigated for 1mm thick cold rolled sheets of commercially pure grade titanium and Ti-6Al-4V alloy. Accelerating voltage of 40kV, beam current of 6mA, and weld speed of 0.8m/min was used and focal position of focused electron beam was just on the surface of workpiece. Microstructure of weld metal, the heat affected zone and base metal was observed using optical microscope. Vickers hardness was measured across the welds and the transverse tensile test was carried out. Hydroformability test was also carried out for the butt welded coupons of commercially pure grade titanium. For the electron beam welded C P Ti, the average grain size was equiaxed $\alpha(15{\sim}25{\mu}m)$ for base metal, coarse equiaxed $\alpha(80{\sim}200{\mu}m)$ for weld metal and annealed and enlarged grain($40{\sim}120{\mu}m$) for the HAZ. The vickers hardness of C P Ti was $180{\sim}200Hv$ for base metal, and $160{\sim}180Hv$ for the weld metal and the HAZ. For the electron beam welded Ti-6Al-4V alloy, the vickers hardness was 360Hv for the base metal, abd $400{\sim}425Hv$ for the weld metal and the HAZ. All the failure occurred at the base metal, when the transverse weld tensile test was carried out for both electron beam welded C P Ti and Ti-6Al-4V alloy. The formability of electron beam welded C P Ti was decreased compared with that of C P Ti base alloy.

  • PDF

E-Magnetron 스퍼터링에 의한 $Al_xTa_{1-x}$ 합금박막의 성장 및 구조적, 전기적 특성 분석 (Growth of $Al_xTa_{1-x}$ Alloy Thin Films by RE-Magnetron Sputter and Evaluation of Structural and Electrical Properties)

  • 송대권;이종원;전종한
    • 마이크로전자및패키징학회지
    • /
    • 제10권2호
    • /
    • pp.55-59
    • /
    • 2003
  • 본 연구에서는 RF-Magnetron 스퍼터링 장치를 이용하여 $Al_xTa_{1-x}$(x=0.0∼1.0) 합금박막을 성장하였고, 4탐침법, XRD, AFM, micro-Vickers 미소경도계를 사용하여 시료의 구조적, 기계적, 전기적 특성을 분석하였다. Al조성 x=0.245(Al 24.5 at.%)에서 전기저항이 가장 높게 나타났고, 결정질이 가장 우수하였다. 표면 hillock에 있어서는 낮은 Al 조성영 역에서는 x가 증가할수록 hillock이 감소하다가, x=0.245에서 hillock이 완전히 배제되었고, 이후 x 증가에 따라 hillock 밀도가 다시 급격히 증가하였다. 미소경도의 경우, Al조성 x=0.2∼0.45의 영역에서 가장 높은 경도값이 측정되었다. 본 연구의 모든 결과를 종합적으로 고려할 때, $Al_xTa_{1-x}$ 합금박막의 결정질, 전기저항, 표면형상, 미소경도는 상호 밀접한 관계를 가지고 있었으며, Al 조성 x=0.245에서 가장 우수한 물리적 특성이 나타났다.

  • PDF