• 한국표면공학회지
• /
• 제29권6호
• /
• pp.797-802
• /
• 1996

Hydrogenated amorphous silicon carbide (a-SiC:H) films have been deposited on unheated substrates by low frequency (50Hz) plasma using $SiH_4+CH_4+H_2$ gas mixtures. Deposition rate, refractive index, optical band gap, Vickers hardness and IR spectrum of the deposited a -SiC:H films have been measured for various rations of gas flow rates k(=$CH_4/SiH_4$, 0.5k4) with a constant $H_2$ flow rate (100sccm). As k increases, the deposition rate of the a-SiC:H films increases up to the maximum value of about 220nm/h at k=2.5, and then it decreases. The refractive index of the films was 2.6 for k=2.5, while the optical band gap of the films was 3.3eV for k=2.2. The maximum value of Vickers hardness of the films was 1500Hv at k=1. The infrared transmission measurement shows that the films contain both Si-C and Si-$CH_3$ bonds.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.87-93
• /
• 2015

This study was performed to develop repair technology for J-Groove dissimilar metal weld of pressurizer heater sleeve in nuclear power plants. Pad, J-Groove automatic welding and mechanical machining equipments to develop repair technology using 'Half Nozzle Repair' were designed and manufactured. To obtain the optimum welding process parameters during Pad temperbead overlay welding, several welding experiments using Taguchi method were conducted. Weldability of Pad overlay weld specimens was estimated by PT/RT test, FE-SEM, EDS and Vickers hardness test. Also, J-Groove welding to adjust weld shape conditions requiring in ASME Code was carried out and its integrity of weld specimens was evaluated through PT/RT test and optical microscope. Consequently, it was revealed that Pad and J-Groove overlay welding for dissimilar metal weld of pressurizer heater sleeve could be possible to meet Code standard without weld defect.

• 한국분말재료학회지
• /
• 제12권1호
• /
• pp.43-50
• /
• 2005

Mechanical alloying using high-energy ball mill and subsequent spark plasma sintering (SPS) process was applied to Al-Fe-Cr and Al-Fe-Mo powder mixture to investigate effects of Cr and Mo addition on thermal stability of Al-Fe, and thereby to enhance its thermal stability up to $500^{\circC}$. Various analytical techniques including micro-Vickers hardness test, SEM, TEM, X-ray diffractometry and corrosion test were carried out. It was found that addition of Cr and Mo to Al-Fe system played a role of grain growth inhibitor of matrix Al and some precipitates such as $Al_3Fe$ during SPS and subsequent heat treatment. The inhibition of grain growth resulted in increased Vickers hardness and thermal stability up to $500^{\circC}$ comparing to those of Al-Fe alloy system.

• 한국결정성장학회지
• /
• 제13권4호
• /
• pp.162-167
• /
• 2003

광페롤용 안정화 지르코니아 소결체의 특성을 평가하기 위하여, A, B와 C사의 원료를 이용하여 1350, 1400 및 $1450^{\circ}C$로 소결하여 시편을 제작하였다. 각각의 열처리 온도에 따른 결정화도, 미세구조 및 기계적 특성을 조사하였다. X-선 회절 분석법과 전계방사 주사형 전자현미경을 이용하여 소결된 시편의 결정화도와 미세구조를 분석하였으며, 만능재료 시험기와 비이커스 경도계를 이용하여 꺽임 강도와 비이커스 경도를 측정하였다 실용적인 측면에서 볼 때, 비교적 저온인 $1350^{\circ}C$로 소결한 시편 B의 경우가 tetragonality도 높고 좋은 기계적인 강도를 나타냈다.

• 동력기계공학회지
• /
• 제21권4호
• /
• pp.94-99
• /
• 2017

Single walled carbon nanotubes were mixed with various metal powders by mechanical ball milling and sintered by spark plasma sintering processes. Two compositional (0.1 and 1 vol%) of the single walled carbon nanotubes were dispersed onto the pure aluminum, 5052 aluminum alloy, pure titanium, Ti6Al4Vanadium alloy, pure copper, and stainless steel 316L. Each composite powders were spark plasma sintered at $600^{\circ}C$ and well synthesized regardless of the matrices. Vickers hardness of the composite materials was measured and they exhibited higher values regardless of the carbon nanotubes composition than those of the pure materials. Moreover, single walled carbon nanotubes reinforced copper matrix composites showed highest enhancement between the other metal matrices system. We believe that low energy mechanical ball milling and spark plasma sintering processes are useful tool for fabricating of the carbon nanotubes-reinforced various metal matrices composite materials. The single walled carbon nanotubes-reinforced various metal matrices composite materials could be used as an engineering parts in many kind of industrial fields such as aviation, transportation and electro technologies etc. However, detail strengthening mechanism should be carefully investigated.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.44-49
• /
• 2013

The influence of thermo-mechanical cycling on the microstructure and strength in the weld coarse-grained heat affected zone (CGHAZ) of Ti-Nb added low carbon HSLA steel was explored through Vickers hardness tests, nanoindentation experiments, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. Undeformed and deformed CGHAZs were simulated using Gleeble simulator with different heat inputs of 30kJ/cm and 300kJ/cm. At high heat input of 300kJ/cm, the CGHAZ consisted of ferrite and pearlite and then their grain sizes were not affected by deformation. At low heat input of 30kJ/cm, the CGHAZ consisted of lath martensite and then the sizes of prior austenite grain, packet and lath width decreased with deformation. In addition, the fraction of particle increased with deformation and this is because the precipitation kinetics was accelerated by deformation. Meanwhile, the Vickers and nanoindentation hardness of deformed CGHAZ with 30kJ/cm heat input were higher than those of undeformed CGHAZ, which are due to the effect of grain refinement and precipitation strengthening.

• Advances in materials Research
• /
• 제9권2호
• /
• pp.99-107
• /
• 2020

Reinforced aluminum alloy base composites have become increasingly popular for engineering applications, since they usually possess several desirable properties. Recently, Warm Accumulative Roll Bonding (WARB) process has been used as a new novel process to fabricate particle reinforced metal matrix composites. In the present study, TiO₂ particles are used as reinforcement in aluminum metal matrix composites fabricated through warm accumulative roll bonding process. Firstly, the raw aluminum alloy 1060 strips with TiO₂ as reinforcement particle were roll bonded to four accumulative rolling cycles by preheating for 5 min at 300℃before each cycle. The mechanical and bonding properties of composites have been studied versus different volume contents of TiO₂ particles by tensile test, peeling test and vickers micro-hardness test. Moreover, the fracture surface and peeling surface of samples after the tensile test and peeling test have been studied versus different amount of TiO₂ volume contents by scanning electron microscopy. The results indicated that the strength and the average vickers micro-hardness of composites improved by increasing the volume content of TiO₂ particles and the amount of their elongation and bonding strength decreased significantly.

• 대한금속재료학회지
• /
• 제47권10호
• /
• pp.660-666
• /
• 2009

The consolidation of mechanical alloyed $Ti_5Si_3$ powder by electro-discharge-sintering has been investigated. A single pulse of 2.5 to 8.0 kJ/0.34 g was applied to each powder mixture using 300 and $450{\mu}F$ capacitors. A bulk-like solid with $Ti_5Si_3$ phase has been successfully fabricated by the discharge with an input energy of more than 2.5 kJ in less than $160{\mu}sec$. Micro-Vickers hardness was found to be higher than 1350, which is significantly higher than that of a conventional high temperature sintered sample. The formation of $Ti_5Si_3$ and consolidation occurred through a fast solid state diffusion reaction.

• 한국재료학회지
• /
• 제32권10호
• /
• pp.414-418
• /
• 2022

Magnesium alloy is the lightest practical metal. It has excellent specific strength and recyclability as well as abundant reserves, and is expected to be a next-generation structural metal material following aluminum alloy. This paper investigated the possibility of thin plate fabrication by applying a overheating treatment to the melt drag method, and investigating the surface shape of the thin plate, grain size, grain size distribution, and Vickers hardness. When the overheating treatment was applied to magnesium alloy, the grains were refined, so it is expected that further refinement of grains can be realized if the overheating treatment is applied to the melt drag method. By applying overheating treatment, it was possible to fabricate a thin plate of magnesium alloy using the melt drag method, and a microstructure with a minimum grain size of around 12 ㎛ was obtained. As the overheating treatment temperature increased, void defects increased on the roll surface of the thin plate, and holding time had no effect on the surface shape of the thin plate. The fabricated thin plate showed uniform grain size distribution. When the holding times were 0 and 30 min, the grain size was refined, and the effect of the holding time became smaller as the overheating treatment temperature increased. As the overheating temperature becomes higher, the grain size becomes finer, and the finer the grain size is, the higher the Vickers hardness.

• 한국재료학회지
• /
• 제32권7호
• /
• pp.326-331
• /
• 2022

AZ31 magnesium alloy was used to manufacture a thin plate using a melt drag method. The effects of roll speed, molten metal temperature, and molten metal height, which are the basic factors of the melt drag method, on the surface shape, the thickness of the thin plate, Vickers hardness, and microstructure of the thin plate were investigated. It was possible to manufacture AZ31 magnesium alloy thin plate at the roll speed range of 1 to 90 m/min. The thickness of the thin plate, manufactured while changing only the roll speed, was about 1.8 to 8.8 mm. The shape of the solidified roll surface was affected by two conditions, the roll speed and the molten metal height, and the Vickers hardness of the manufactured magnesium alloy thin plate value ranged from Hv38~Hv60. The microstructure of the thin plate produced by this process was an equiaxed crystal and showed a uniform grain size distribution. The grain size was greatly affected by the contact state between the molten metal and the solidification roll, and the amount of reactive solids and liquids scraped at the same time as the thin plate. The average grain size of the thin plate fabricated in the range of these experimental conditions changed to about 50-300 ㎛.