• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.226-230
• /
• 2013

We performed high pressure high temperature (HPHT) sintering for the 20 nm MgO powders at the temperatures from $600^{\circ}C$ to $1200^{\circ}C$ for only 5 min under 7 GPa pressure condition. To investigate the microstructure evolution and physical property change of the HPHT sintered MgO samples, we employed a scanning electron microscopy (SEM), density and Vickers hardness measurements. The SEM results showed that the grain size of the sintered MgO increased from 200 nm to $1.9{\mu}m$ as the sintering temperature increased. The density results showed that the sintered MgO achieved a more than 95% of the theoretical density in overall sintering temperature range. Based on Vickers hardness test, we confirmed that hardness increased as temperature increased. Our results implied that we might obtain the dense sintered MgO samples with an extremely short time and low temperature HPHT process compared to conventional electrical furnace sintering process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.78-88
• /
• 2000

The effect of post-weld heat treatment(PWHT) of SCM440 steel was investigated with parameters such as micro-Vickers hardness, corrosion potential, polarization behaviors, galvanic current, Al anode generating current and Al anode weight loss, etc. Each hardness of three parts(HAZ, BM, WM) by PWHT is lower than each of as-welded parts. However, hardness of WM area was the highest among those three parts in case of both PWHT and as-welded. Corrosion potential of WM part was the highest among those three parts and WM area was also acted as cathode without regard to PWHT. The magnitude of corrosion potential difference among three parts by PWHT was larger than that of three parts of as-welded, and corrosion current by galvanic cell of these three parts by PWHT was also larger compared to as-welded. Therefore, it is suggested that corrosion resistance property of SCM440 steel is decreased by PWHT than as-welded. However, both Al anode generating current and anode weight loss were also increased by PWHT compared to as-welded when SCM400 steel is cathodically protected by Al anode.

• Korean Journal of Metals and Materials
• /
• v.50 no.4
• /
• pp.263-270
• /
• 2012

This study investigates the effect of heat treatment on the mechanical properties of a forged Ni-based superalloy called Nimonic 80A. Nimonic 80A ingot samples were fabricated by vacuum spray casting to achieve a fine and homogenized microstructure. The ingot samples were subsequently hot-forged with the diameter of 220 mm at 1373 K. From the center to the surface of the forged Nimonic 80A, its average grain size decreased and its micro-Vickers hardness increased slightly. Solution treatment was carried out at 1353 K with 8 hours of air cooling followed by aging treatment, which was carried out in the range of 873-1073 K with various times from 0.5 to 256 hours. To set the optimum aging conditions, micro-Vickers hardness tests were performed. The maximum hardness value of 388.0 Hv was obtained by aging at 973 K for 32 hours. Also, tensile tests were performed for optimum aging conditions at room temperature and 873 K. The results can be used effectively to perform reasonable heat treatment of Nimonic 80A superalloy.

• The Journal of the Korean dental association
• /
• v.58 no.6
• /
• pp.324-335
• /
• 2020

We investigated whether fluoride varnishes recover the hardness of bovine teeth under 20 days of demineralization/remineralization cycling. The fluoride varnish groups (two commercial fluoride varnishes [V-varnish (Vericom, Korea) and CavityShield (3M ESPE, USA)] and an experimental fluoride varnish including 5 wt.% NaF were compared with a control group without fluoride varnish. Vickers hardness was measured at baseline, 3 days after immersion in caries-inducing solution, 24 hours after application of a fluoride varnish, and after 10 and 20 days of demineralization/remineralization cycling. Afterward, tooth surfaces were observed by scanning electron microscope. After fluoride varnish application and the cycling 10 and 20 days, the experimental varnish group showed the highest hardness, while the CavityShield and the control groups demonstrated the lowest hardness. The experimental varnish group recovered the hardness of the baseline at 24 hours after application of the varnish, while it was recovered after 20 days of the cycling in case of the V-varnish. However, the CavityShield and the control groups did not recover the hardness even after 20 days of the cycling. The experimental fluoride varnish with fast recovery in the hardness of the baseline can be used as an effective fluoride varnish to resist demineralization and to facilitate remineralization.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.3
• /
• pp.127-135
• /
• 2002

Shore hardness test was developed in 1906 to overcome the limit of Brinell hardness test. However, the detailed requirements on the tester was not clearly specified except the scale, i.e., 100 HS for high carbon steel and 10 HS for soft brass. As a result, the shore hardness was used for quite long time without well established standards. For the establishment of hardness standards, standard tester, standard procedure, and standard hardness block must be provided. So far the standard of Shore hardness was maintained by correlating Shore hardness scale to Vickers hardness through converting equation. This is the so called converted Shore hardness and it is not the true Shore hardness standard strictly. In this paper, the possibility of establishing Shore hardness standard based on the Shore standard hardness tester is reported.

• Journal of Technologic Dentistry
• /
• v.26 no.1
• /
• pp.77-88
• /
• 2004

Glass ceramics for dental crown prosthesis were prepared by crystallization of CaO-MgO-SiO2-P2O5-TiO2 glasses. Their crystallization behaviors have been investigated as a function of heattreatment temperature and holding time in relation to mechanical properties. The results are as follows: Vickers hardness and bending strength of glass ceramics increased due to the precipitation of apatite, whitlockite, $\beta$-wollastonite, magnesium titanate, and diopside crystal phases within glass matrix. The final crystalline phase assemblages and the microstructures of the glass ceramics were found to be dependent on heat-treatment temperature and holding time. Vickers hardnes and bending strength of glass ceramics increased with increasing heat-treatment temperature and holding time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4185-4190
• /
• 2013

We executed the property changes of the sintered MgO (99.9% purity, 300nm size) specimens with addition to CaO content of 0.00wt%, 0.25wt%, and 0.50wt%, processed at 7GPa, for 5min, 600~$800^{\circ}C$. To investigate the micro-structure and physical property changes of the sintered MgO(-CaO), we employed a scanning electron microscopy(SEM), X-ray diffractomerty(XRD), Vickers hardness, and density. The SEM result showed that MgO powder of 300nm size was changed into sintered structure of 520nm by high pressure and low temperature sintering, regardless of the CaO contents. According to the XRD analysis, no CaO phase observed, while MgO peaks shift indicated the existence of CaO in the MgO matrix. The Vickers hardness result showed that hardness of sintered MgO-CaO increased by 12% compared pure MgO under the same temperature conditions. It implied that we can obtain the same hardness with $100^{\circ}C$ lowered sintering temperatures by addition of CaO. The density results showed that it was possible to obtain density of 98%, which is 5% greater than that of pure MgO at low temperature of $600^{\circ}C$.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.142-148
• /
• 2004

It is already known that hardness number of cold-forged product is in close conjunction with its effective strain. This paper presents the method to predict the relation between effective strains and hardness by using FE-simulation of hardness test from the conception that hardness indicates resistance to plastic deformation. The results of FE-simulation for the materials are compared with those of experiments and also compared with those of experiments in reference to show the feasibility of the proposed method. In addition, the present method was applied to the cold-forged product to verify the relation between hardness and effective strain. As a result, the predicted hardness number by the present method is in good agreement with experimental values. Prediction of hardness fur a cold-forged product comes to be possible by estimating the relation between effective strain and hardness using the proposed method in this study.

• International Journal of Ocean System Engineering
• /
• v.2 no.4
• /
• pp.244-249
• /
• 2012

In this study, a monolithic MoSi2 matrix reinforced with 20 vol% SiC particles, a SiC/MoSi2 composite matrix reinforced with 20 vol% ZrO2 particles, and a ZrO2/MoSi2 composite were fabricated using hot press sintering at $1350^{\circ}C$ for 1 h under a pressure of 30 MPa. The Vickers hardness and sliding wear resistance of the monolithic MoSi2, ZrO2/MoSi2, and SiC/MoSi2 composite were investigated at room temperature. A wear behavior test was carried out using a disk-type wear tester with a silicon nitride ball. The ZrO2/MoSi2 composite showed an average Vickers hardness value and excellent wear resistance compared with the monolithic MoSi2 and SiC/MoSi2 composite at room temperature.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.1
• /
• pp.45-51
• /
• 2004

In this paper, the relationship between the mechanical properties of alumina abrasives and grinding performance was investigated. Micro vickers hardness and fracture strength of all abrasives used in this study were measured. The grinding experiments were earned out with alumina grinding wheels made by various kinds of alumina abrasives including 32A, WA, ART, ALOMAX, and RA. The performance of such grinding wheel for grinding SKD11 was evaluated by specific grinding energy, grinding-ratio, and surface roughness. The grinding wheels composed by the harder abrasives and the lower fracture strength abrasives showed better grinding performance.