• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.3
• /
• pp.220-225
• /
• 2014

Generally, the nonlinearity of ultrasonic waves is measured using a nonlinear parameter ${\beta}$, which is defined as the ratio of the second harmonic's magnitude to the power of the fundamental frequency component after the ultrasonic wave propagates through a material. Nonlinear parameter ${\beta}$ is recognized as an effective parameter for evaluating material degradation. In this paper, we evaluated the nonlinear parameter of Al6061-T6 which had been subjected to an artificial aging heat treatment. The measurement was using the transmitted signal obtained from contact-type transducers. After the ultrasonic test, a micro Vickers hardness test was conducted. From the result of the ultrasonic nonlinear parameter, the microstructural changes resulting from the heat treatment were estimated and the hardness test proved that these estimates were reasonable. Experimental results showed a correlation between the ultrasonic nonlinear parameter and microstructural changes produced by precipitation behavior in the material. These results suggest that the evaluation of mechanical properties using ultrasonic nonlinear parameter ${\beta}$ can be used to monitor variations in the mechanical hardness of aluminum alloys in response to an artificial aging heat-treatment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.603-611
• /
• 2020

A porous material which can contain liquid perfume was manufactured by adding 1~4 wt% of polysiloxane into a composite containing 20 ㎛ Ag powder and 30 wt% of 53 ㎛ salt, sintering for 60 min at 750℃, and melting salt selectively. The changes in pore, hardness, and microstructure were confirmed according to the polysiloxane content both before and after sintering. The manufactured silver liquid container was formed with open pores both before and after sintering, and the container shrunk by 2~7 % in both perpendicular and parallel directions after sintering. Vickers hardness was increased after sintering and was doubled when 2 wt% of polysiloxane was added. In case of the microstructure, the surface condition of the silver liquid container became darker according to the polysiloxane content, and the pore size was decreased from 50 ㎛ to under 10 ㎛. The composition distribution result revealed an even distribution when 2 wt% of polysiloxane was added but uneven distribution when over 3 wt% of polysiloxane was added due to decreased hardness by cluster. Therefore, the addition of an appropriate amount of 2 wt% polysiloxane reinforced the porous silver with open pores to offer application for jewelry usage.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.42-50
• /
• 2016

Overlay welding affects the chemical components and weld hardness by dilution of the lamination layer thickness, which determines the surface properties. This study experimentally investigates different numbers of layers for overlay welding monel materials, which are anti-corrosion materials. The Fe content, weldability of the base metal and monel materials, hardness, and surface flatness were examined. Each evaluation was carried out after overlay welding with three layers on the base material and pipe base material of the plate. The Fe content was evaluated by analyzing the constituents of each layer. The Fe content was satisfactory in the three layers. The weldability of the laminate specimens was evaluated by a bending test. The hardness and bead flatness of the laminate specimens were evaluated by micro Vickers and 3D measurements. The hardness was highest in the heat-affected zone with one layer, and it decreased with increasing lamination. In the case of bead flatness, there is a sharp difference in the deviation with increasing numbers of laminations, which should be considered carefully.

• Journal of Technologic Dentistry
• /
• v.39 no.2
• /
• pp.75-82
• /
• 2017

Purpose: This study provided the basic data for selection the zirconia block and CAM by means of marginal fitness observations, flexural strength test and hardness test. Methods: Three dental zirconia blocks(ABCera, NaturaZ, ST98) and two dental milling machines(CAD/CAM MS, DWX-50) were used in this study. Metal abutment(diameter 10 mm, height 5 mm, inclined angle $3^{\circ}$ taper, 1 mm chamfer margin) was fabricated by Ti customized abutment, and then zirconia copings were fabricated for each ten specimens. Silicone replica technique was used to observe the marginal fitness of cross-sections with a stereomicroscope at ${\times}50$ magnification. The dental zirconia blocks was cut into 10 pieces each having a size of $25mm{\times}5mm{\times}1mm$, and fabricated according to the manufacturer's instructions, and flexural strength was measured using a universal testing machine. For hardness test, a micro Vickers hardness tester was used as it was in the flexural strength test. Statistical analysis was performed by one way ANOVA and post-test was performed by Scheffe test. Results: For marginal fitness of bucco-lingual axial, ZU group($59.7{\pm}10.3{\mu}m$) was the lowest, followed by RA, ZA, ZD, RD, RU. For marginal fitness of mesio-distal axial, ZU group($59.3{\pm}10.2{\mu}m$) was the lowest, followed by RA, ZA, RD, ZD, RU. One-way ANOVA showed statistically significant difference between groups(p<0.05). For flexural strength, ABCera block($718.0{\pm}57.2MPa$) was the highest, followed by NaturaZ, ST98. For hardness, ABCera block($1550.3{\pm}19.8Hv$) was the highest, followed by ST98, NaturaZ. There was no significant difference in flexural strength and hardness between blocks(p>0.05). Conclusion: Based on the results of this study, the type of dental zirconia block did influence the marginal fitness, and all dental zirconia blocks are expected to be suitable for clinical application. The highest flexural strength and hardness were ABCera block, and no statistically significant difference was observed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.2
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• 전자공학회논문지 IE
• /
• v.49 no.2
• /
• pp.1-8
• /
• 2012

The effects of the addition of either monoclinic $ZrO_2(pure)$ or tetragonal $ZrO_2$ containing 5.35wt% $Y_2O_3(Y-TZP)$ on the mechanical properties and thermal shock resistance of $Al_2O_3$ ceramics were investigated. The addition of $ZrO_2$(m) and Y-TZP increased sintered density of $Al_2O_3$. The Vickers hardness also increased as the volume fraction of Y-TZP increased going through a maximum at 20wt%. The hardness of the specimens was found to be dependent on the sintered density. The higher volume fraction of either $ZrO_2(m)$ or Y-TZP resulted in the higher fracture toughness of the composite was. This result may be taken as evidence that toughening of $Al_2O_3$ can be achieved by not only the transformation toughening but microcrack toughening of $ZrO_2$. The thermal shock property for $Al_2O_3-ZrO_2$ composites was improved by increasing the volume fraction of monoclinic $ZrO_2(pure)$. The grain size increased as the volume fraction of $ZrO_2$ did.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.341-349
• /
• 2002

Electrical, mechanical and sinterability properties of yttria-stabilized zirconia doped with 5.35wt% $Y_2$O$_3$(Y$_2$O$_3$- containing stabilized zirconia : YSZ) were studied as a function of $Al_2$O$_3$, CoO, Fe$_2$O$_3$ and MnO$_2$ addition. The ratio of monoclinic phase to tetragonal phase was changed by the addition of $Al_2$O$_3$, CoO, Fe$_2$O$_3$ and MnO$_2$ to 8.00 wt% and sintered density decreased with increasing $Al_2$O$_3$, CoO, Fe$_2$O$_3$ and MnO$_2$ addition. Fracture toughness increased with the increase of monoclinic to tetragonal phase ratio and was maximum at about 18%. When transition metals such as CoO, Fe$_2$O$_3$ or MnO$_2$ was added more than 1.5 wt%, the electrical conductivity of YSZ increased. But $Al_2$O$_3$ hardly affected the electrical conductivity of YSZ. The addition of $Al_2$O$_3$, CoO, Fe$_2$O$_3$ and MnO$_2$ into YSZ resulted in the more complex behavior of fracture toughness and hardness variation and the specimen with 1.5wt%-Fe$_2$O$_3$, 3.0wt%-Al$_2$O$_3$ and 1.5wt%-CoO showed the monoclinic to tetragonal phase ratio of 18% and the highest toughness of 10.8 MPa.m$^{1}$2/ and Vickers hardness of 1201 kgf/mm$^2$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1087-1093
• /
• 2014

Stainless steels stabilized with Ti or Nb are largely used in offshore and shipbuilding industries due to its excellent corrosion resistance. In this study, carbide stabilizers, Ti and Nb, were added to stainless steel 304 specimens with different concentrations(Ti: 0.26%, 0.71%, Nb: 0.29%, 0.46%, 0.71%), and their mechanical and electrochemical characteristics were evaluated. Micro-Vickers hardness testing was employed to characterize the mechanical characteristics with alloying elements. Electrochemical evaluation techniques including Tafel analysis, cyclic polarization experiment, galvanostatic experiment were utilized to compare the corrosion characteristics of the specimens. The result of hardness tests revealed that Nb containing specimens showed increasing hardness with increasing alloying contents while adding Ti had little effect on increase in hardness. In the case of electrochemical measurements, the electrochemical characteristics of the specimens were enhanced with increasing Nb contents while they were deteriorated with increasing Ti contents. As a result, different stabilizers and their contents may produce significant differences in electrochemical characteristics, and there such effect must be taken account of in development of stainless steels for marine environment.

• Journal of dental hygiene science
• /
• v.17 no.4
• /
• pp.358-367
• /
• 2017

The purpose of this study was to evaluate the influence of water infiltration and flexural strength changes in dental porcelain with glazing treatment. The block specimens were prepared as experimental materials, using feldspar type commercial dental porcelain; then, these were fired at $940^{\circ}C$ for 1 minute. The fired specimens were polished with a dimension of $40{\times}5.5{\times}5mm$. The specimens were distributed to two experimental groups: with and without glazing treatment specimens (n=5), and they were immersed in a solution of pH 7 for 3, 7, and 20 days at $40^{\circ}C$ after fabrication. To evaluate the flexural strength changes with water infiltration treatment in specimens with and without glazing, the 3-point flexural test was performed, using a universal testing machine until failure occurred. Starting powder and fired specimens consisted of amorphous and leucite crystalline phase. The Vickers hardness of fired specimens was more than 1.6 times higher than that of the enamel of natural teeth. According to porosimeter results, the specimens without glazing treatment exhibited a porosity of about 14.7%, whereas the glazed specimens exhibited the lowest porosity at about 1.1%. The average flexural strength of glazed specimens was higher than the flexural strength of specimens without glazing treatment (p<0.05). The flexural strength of all specimens with and without glazing treatment deteriorated with accelerated aging in the solution. In addition, significant differences between these two treatment groups were observed in all of the specimens treated at various water infiltration periods (p<0.05). The exposure of internal pores and micro-cracks in the surface due to polishing of the fired specimens influenced mechanical behaviors. Especially, the flexural strength in specimens without glazing treatment has shown significant degradation with the infiltration of water. Therefore, this study suggests that glazing processes can improve mechanical properties of dental porcelain.

• Journal of Korean society of Dental Hygiene
• /
• v.9 no.4
• /
• pp.740-752
• /
• 2009

Objectives : This study was carried out to examine the effect of varnish fluoride and APF gel on the acid resistance and the remineralization of the enamel. Methods : At first, the microhardness changes of enamel surface were measured after demineralizing the fluoride treated tooth surface. Next, the changes were measured after fluoride application to the demineralized enamel surface. Results : 1. Acid resistance was higher in varnish fluoride groups than APF gel groups and the difference was significant(p<0.001). 1) Varnish fluoride groups Microhardness of enamel surface showed $297.76{\pm}9.89$ after fluoride treatment and $260.90{\pm}28.67$ after drmineralization. The changes of Vickers hardness number(VHN) were $-36.86{\pm}27.30$. 2) APF gel groups Microhardness of enamel surface showed $298.79{\pm}17.28$ after fluoride treatment and $43.75{\pm}18.58$ after demineralization The changes of VHN were $-255.04{\pm}21.31$. 2. No significant changes were surveyed in both varnish fluoride groups and APF gel groups as for remineralization of enamel(p>0.05). 1) Varnish fluoride groups Microhardness of enamel surface showed $46.58{\pm}15.42$ after demineralization and $46.61{\pm}15.70$ after fluoride treatment. The changes of VHN were $0.02{\pm}3.75$. 2) APF gel groups Microhardness of enamel surface showed $47.13{\pm}19.31$ after demineralization and $42.59{\pm}16.12$ after fluoride treatment. The changes of VHN were $-4.54{\pm}5.06$. Conclusions : Varnish fluoride showed higher acid resistance than APF gel, however both of them were observed to have no effect on the remineralization of the enamel.