• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.385-388
• /
• 2001

The cutting performance of a machine depends on the ability of the design of the acoustic horn to facilitate an increase in tool-tip vibration, allowing a significant amount of material to be removed. In this paper, three kinds of acoustic horns were designed and FEM was used to estimate displacement magnifications of horn tips. An optimization procedure for the profile has been followed to obtain maximum magnification, for higher rate of material removal and safe working stresses for the horn material.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.187-189
• /
• 2006

In mechanical system, gear trains have backlash innately. With the presence of inherent backlash, the overall system performance is limited in many practical control systems. It has been reported that a disturbance observer has the property of effective removing disturbance and cutting measurement noise off. The plant is remodeled with modified disturbance observer to observe and compensate backlash characteristics. And this paper describes a method to design Q filter and to analyze the effects of disturbance and measurement noise to the output. It is shown that the vibration and tracking error caused by backlash were decreased and the time constant and relative degree are important factor to design Q filter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.971-974
• /
• 2001

In this study, the static and dynamic characteristics of endmilling process was modelled and the analytic realization of chatter mechanism was discussed. In this regard, We have discussed on the comparative assessment of recursive time series modeling algorithms that can represent the machining process and detect the abnormal machining behaviors in precision endmilling operation. In this study, simulation and experimental work were performed to show the malfunctional behaviors. For this purpose, new recursive(RLSM) were adopted for the on-line system identification and monitoring of a machining process, we can apply these new algorithms in real process for detection of abnormal chatter. Also, the stability lobe of chatter was analysed by varying parameter of cutting dynamices in regenerative chatter mechanics.

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.7-14
• /
• 1998

Noncircular gears have been used for obtaining the modified anglualr velocity ratio between parallel axes. The elliptical gear, which is a kind of noncircular gears, makes use of ellipse as a pitch curve, and is applied for the measurement of the discharge of liquid. The applications of an elliptical gear are more advantageous than any other mechanism as like a crank-slider linkage or a cam mechanism in view of the accuracy and the reliability to transmit the prescribed motion. In this paper, acceding to the theoretical involute tooth profile, two pairs of the elliptical gears were manufactured by using CNC wire electronic discharge machine. The proper ranges of the operating pressure angle and of module not to generate under cutting are studied on the change of the eccentricity, because it is the eccentricity of the pitch curve that determines most of the characteristics of the elliptical gear and then the vibration analysis is executed for the verification of harmonious rotating.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.287-293
• /
• 2001

Resently, reduction of industrial products in size and weight has increased by the application of micro-drill for gadgets of high precision and gave rise to a great interest in a micro-drilling. Due to the lack of tool stiffness and the chip Packing, micro-drilling requires not only the robust tool structure which has not affected by the vibration, but also the effective drilling methods designed to prevent tool fracture from cutting troubles. Firstly, this paper presents a new manufacturing process of micro-drill for improving the Product rate and an optimum shape of micro-drill for lengthening the tool life, and secondly between tool life and drilling torque acquired in the inprocess monitoring system.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.76-83
• /
• 2001

In this study, the static and dynamic characteristics of turning process was modelled and the analytic realization of regen-erative chatter mechanism was discussed. In this regard, we have discussed on the comparative assessment of recursive times series modeling algorithms that can represent the machining process and detect the abnormal machining behaviors in precision turning operation. In this study, simulation and experimental work were performed to show the malfunction behaviors. For this purpose, new Recursive Extended Instrument Variable Method(REIVM) was adopted for the on-line system identification and monitoring of a machining process. Also, we can apply REIVE algorithms in real process for the detection of chatter frequency and dynamic property and analyze the stability lobe of the system by changing a parameter of cutting dynamics in regenerative chatter mechanics, if it is stable or unstable, Also, The stability lobe of chatter was analysed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.883-886
• /
• 2001

The mechanical properties such as the Young's modulus, damping ratio, vibration mode and hardness of the disk materials heat-treated under various conditions are measured, and the relations between there properties and the cutting characteristics such as early tip fracture are examined. The results obtained from this study are as follows. The circular saw with the V-Cr added disk has higher young's modulus and damping ratio than the saw with STC5 disk, preventing the early fracture of tungsten carbide due to the above properties. The circular saw with the disk which is subjected to the heat treatment at the quenching temperature of $830^{\circ}C$ and at the temperature of $550^{\circ}C$ have the best tool life and surface roughness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.947-951
• /
• 1997

Recently, the necessity of the detection of abnormal machining process is being emphasized in order to improve the machining accuracy and reduce the cost in unmanned operating system. The vibration by chatter generated in cutting processes within machine tools is a relative motion between tools and workpieces. So, if the chatter occurs, the surface roughness and accuracy of workpieces will be deteriorate and it leads to the rapid wear of tools. The author intended to use the I /sab/RMS (current of root mean square) of current sigals and the movimg C.V. (coefficient of variation) of each phase for the detection method of chatter.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.171-178
• /
• 2002

With increasing the needs for micro and precision parts, micro machining technology using micro tools has been studied to fabricate a small part with high density such as electronics, optics, communications, and medicine industry more than before. Though these micro tools have developed rapidly, it is difficult to apply them to micro fabrication technologies, because of the inherent manufacturing. In this study, micro tools (WC) to produce micro structures and parts were manufactured by cylindrical grinding machine employing ELID (Electrolytic In-process Dressing) technique and the micro tools are fabricated as square shape with the dimension less than 100${\mu}{\textrm}{m}$. With the micro tools on the same machine, characteristics of micro grooving and drilling are evaluated. Also we compare normal micro machining with ultrasonic micro machining on the vibration table. It is confirmed that the developed micro tools are fully applicable to micro grooving, micro drilling and free form cutting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.873-877
• /
• 1997

This paper presents experimental results to know the charcteristics of machined surface due to cutter runout. Cutter runout is a common but undesirable phenomenon in multi-tooth machining such as end-milling process because it introduces variable chip loading to insert which results in a accelerated tool wear, amplification of force variation and hence enargement vibration amplitude. To develop in-proess cutter runout compensation system, set-up the micro-positoning mechanism which is based on piezoelectric translator embeded in the work holder to manipulate the depth of cut in real-time. And feasibility test of system was done under the various experimental cutting conditions. This results provide lots of information to build-up the precision machining technology.