• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.613-620
• /
• 2014

A few Humidifier have vibration problems caused by velocity of flow, piping vibration and karman vortex. The crack is generated on pipe wall and humidifier are damaged. Vibration analysis is conducted to prevent pipe damage during the design. But the other problem are caused after analysis of vibration. Therefore in this paper, the vibration and static analysis have been measured and analyzed for pipes and curve. Also modal test is conducted for analysis of natural frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.132-139
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue (HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.403-408
• /
• 2007

According as diesel automobile are produced, reduce noise and vibration that is occurred by characteristic of diesel engine, and need engine room layout optimization and research for light weight of parts. Balance Shaft Module is module parts for vehicles engine to improve performance and efficiency of engine and reduce noise and vibration. These days, an oil pump integrated balance shaft module and an oil sump integrated balance shaft module is on the rising for optimizing of engine room. In this study, produced prototype of oil pump integrated type balance shaft module, and achieved dynamic characteristic test about experimental modal analysis and noise/vibration of balance shaft module.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.310-315
• /
• 2017

Although studies evaluating the effects of the blasting vibration on the adjacent structures from various angles have continued, cases of securing the safety of the adjacent buildings and researching the proper blasting method for the field condition by analyzing the vibration waveform of the measuring field while performing the open pit blasting are poor. Therefore, it is necessary to present a remedy for blasting pattern selection through test blasting that is appropriate for field conditions, and is economical and efficient. In this study, open pit blasting work was conducted based on the separation distance applied according to the standard blasting method by test blasting and the vibration regulation standard in the road expansion construction site to measure the blasting vibration value, and the vibration prediction equation by blasting methods was examined using a regression analysis computer program to calculate K, N, and R of the confidence level 95%. By setting the blasting allowed vibration standard of the test blasting target area to 0.3cm/sec, and the charring weight and blasting method by the separation distances according to the blasting vibration estimation equation of the open pit blasting guideline and the blasting vibration estimation equation of the test blasting were compared/analyzed, it was possible to identify the factors that increased the working expenses. In addition, the measurement and analysis of the adjacent structures during open pit blasting and the blasting vibration were performed after selecting the most adjacent structure to the open pit blasting spot to analyze the problems on the test blasting procedure and analysis method in the open pit blasting design/construction guidelines, which appeared in the process of completing open pit blasting construction, and a remedy is presented.

• Journal of KSNVE
• /
• v.7 no.2
• /
• pp.331-345
• /
• 1997

A theoretical formulation for the analysis of free vibration of clamped-free cylindrical shells with plates attached at arbitrary axial position(s) was completed and it was programed to get the numerical results which yield natural frequencies and mode shape of the combined system of the plate and the shells. The frequencies and mode shapes from theoretical calculation were compared with those of commercial finite element code, ANSYS. In order to validate the theory, modal test was also performed by impact test and FFT analysis. The results shows good agreement with those of ANSYS and test results in frequencies and mode shapes. The method developed herein is likely to be used for the analysis of the free vibration of the clamped-free circular cylindrical shells with any kinds of lids such as hollow circular plates, conical shells, spherical shells, or semi-spherical shells.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.12-17
• /
• 2006

The bridge to be analyzed is a self-anchored suspension bridge which is constructed within the country. Forced vibration test was performed with oscillator for verification of safety, maintenance and management. In this study, the feasibility of deduction was verified with the modified analysis model by comparing natural frequency, natural mode and damping ratio of the real bridge, which are obtained from the vibration test of the whole bridge after construction of 3-dimensional self-anchored cable suspension bridge, with the eigenvalue of analytic computation model and evaluating them. As a result of study, the friction of bridge bearing must be considered to get the natural frequencies of flexural vibration, and evaluating the polar moment of inertia is critical factor in analysis modeling in case of torsional vibration. The logarithmic damping ratio of the test appeared to exceed the ordinary one assumed at the design phase.

• Journal of Korean Society for Quality Management
• /
• v.43 no.3
• /
• pp.341-358
• /
• 2015

Purpose: This paper presents graphic methods and desirability function approach to determine best vibration reducing configuration for Surion helicopter. Many flight tests were executed and nine vibration levels in cockpit, cabin, and engine room were measured in each test and analyzed to find optimal configuration. Methods: Graphic analysis methods such as matrix, scatter, and box plots are used to identify better vibration-reducing flight test conditions. As an integrated measure of the performance of 9 vibration levels desirability function approach is adopted. Results: Three vibration reducing configurations are found to be proper and one configuration is recommended. Conclusion: It is expected to be helpful to adopt graphic and desirability function methods presented in this paper in developing new products or systems like helicopters. For efficient and effective flight testing of helicopters, it will be necessary to have consistently homogeneous environment for flight testing and applying design of experiments techniques and analyzing test data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.1-7
• /
• 1995

Vehicle has two kinds of mirrors to check the rear. Especially inner rear-view mirror(room mirror) is easy to vibrate. A vibration of vehicle inner rear-view mirror affects safe driving. This study presents both of analysis of cause of mirror vibration and resolution in order to improve that throughout analysis by elasticity theory, FEM, and test.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.81-85
• /
• 1997

It is a well known fact that the exciter used in the vibration test interacts with the test structure and thus influences the test results. A two degree of freedom model of exciter is suggested and the vibration parameters of this model is experimentally extracted. According to this experimental results, the vibration parameters of the exciter can vary with respect to the test structure as well as the stinger used in the connecting mechanism. It is also found that the vibration parameters provided by the manufacturer can not be accurate and these parameter values should be revaluated based on the test environments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.341-344
• /
• 2004

This paper presents results of test for combustion vibration in the pilot furnace for fossil power plant under combustion test. We measured static pressure variation in the pilot furnace together with air and fuel flow. From test results, it shows that vibration magnitude is affected by air and fuel flow. Also, a finite element analysis using a commercial S/W is performed to calculate acoustic mode of the pilot furnace. These results show that dominant frequency occurred is related to acoustic natural frequency of furnace. After this, it needs to be studied the relation between dominant frequency of combustion vibration and air flow rate.