• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.12
• /
• pp.1185-1191
• /
• 2011

The kinematic characteristics of cutting device significantly affects cutting performance in 2-dimensional elliptical vibration cutting(EVC) where the cutting tool cuts workpiece, traversing a micro-scale elliptical trajectory in a trochoidal motion. In this study, kinematical characteristics of EVC device constructed with two parallel stacked piezoelectric actuators were analytically modeled and compared with the experimental results. The EVC device was subjected to step and low-frequency(0.1 Hz) sinusoidal inputs to reveal only its kinematical displacement characteristics. Hysteresis in the motion of the device was observed in the thrust direction and distinctive skew of the major axis of the elliptical trajectory of the cutting tool was also noticed. Discrepancy in the voltage-to-displacement characteristics of the piezoelectric actuators was found to largely contribute to the skew of the major axis of the elliptical trajectory of the cutting tool. Analytical kinematical model predicted the cutting direction displacement within 10 % error in magnitude with no phase error, but in estimating the thrust direction displacement, it showed a $27^{\circ}$ of phase-lag compared with the measured displacement with no magnitude error.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.9
• /
• pp.903-909
• /
• 2012

In elliptical vibration cutting(EVC) where the cutting tool traces a micro-scale 2-dimensional elliptical trajectory, the kinematical and vibrational characteristics of the EVC device greatly affect cutting performance. In this study, kinematical and vibrational characteristics of an EVC device constructed with two orthogonally-arranged stacked piezoelectric actuators were investigated both analytically and experimentally. The step voltage was applied to the orthogonal EVC device and the associated displacements of the cutting tool were measured to assess kinematical characteristics of the orthogonal EVC device. To investigate the vibrational characteristic of the orthogonal EVC, sinusoidal voltage was applied to the EVC device and the resulting displacements were measured. It was found from experiments that coupling of displacements in the thrust and cutting directions and the tilt of the major axis of the elliptical trajectory exists. In addition, as the excitation frequency is in vicinity of resonant frequencies the distortion in the shape of the elliptical trajectory becomes greater and change in the rotation direction occurs. To correct the shape distortion of the elliptical trajectory, the shape correcting procedure developed for the parallel EVC device was applied for the orthogonal EVC device and it was shown that the shape correcting method successfully corrects distortion.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.11
• /
• pp.1214-1220
• /
• 2012

Vibration assisted cutting (VAC) is one of the promising methods for precision machining, which has been normally equipped with piezoelectric materials. In this paper, a feasibility of applying magnetostrictive materials to VAC as a cutting device instead of piezoelectric materials was studied. For this, the vibrational characteristics of a magnetostrictive material was investigated with respect to a coil design, a preload, and the effects of a biasing and an exciting magnetic fields. The output strain of a magnetostrictive material is restricted due to an increasing inductive impedance as the exciting frequency increases and the heat of coil, etc. Through the experimental results, it was found that the biasing and the exciting magnetic field affected the output performance significantly but not the preload. In conclusion, the magnetostrictive material could be used only in the low frequency range but not a good candidate for high frequency actuating application.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.261-264
• /
• 2004

This paper presents the design and test of elliptical vibration assisted cutting tool post. It is actuated by two piezoelectric actuators which are connected to the moving part through the elastic hinge with its role of imposing the preliminary pressures. These two actuators are located at right angles so that the resulting tool tip moves like a two-dimensional ellipse. Also, the tool post is activated within the region of linear actuation in order to overcome the distorted elliptical motion. For the precise measurement of the displacement of the tool tip, three-dimensional experimental apparatus was designed and the strokes of the tool post in major and minor axes were measured. The results show that the tool post can produce the variety of vibration locus from a circle with a radius of 5 ${\mu}{\textrm}{m}$ to an ellipse with a major axis, a =10 ${\mu}{\textrm}{m}$, and a minor axis, b =2.5 ${\mu}{\textrm}{m}$

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.268-273
• /
• 2011

In light guide panels, the PMMA sheet that is used in liquid crystal displays plays an important role in scattering the incident light and requires very fine machining as the sheet is directly related to the optical characteristics of the panels. High speed end milling(HSE) and high speed shaping(HSS) processes that are widely adopted and applied to the precise machining of light incident plane through vibration-assisted HSS for increasing the optical quality by minimizing the above-mentioned problems. The cutting tool and the tool post presented in this paper are designed by the authors to increase the magnitude of the cutting stroke by adopting the resonant frequency without weakening the stiffness and to reduce vibrations during even high speed feeding. The dynamic haracteristics of thecutting tool and the tool post are evaluated through simulation and experiment as well. The results reveal very appropriate dynamic characteristics for vibration-assisted HSS.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.215-222
• /
• 2014

This paper presents an experimental study of a vibration-assisted dry micro-wire electrical discharge machining (${\mu}$-WEDM) utilized in high precision and micro-manufacturing area. The assisted vibration was applied to the workpiece using a piezoelectric actuator, and high pressure air was injected directly into the machining gap through a nozzle. Investigation experiments were performed to estimate the importance of input parameters and it was observed from experiment results that the width (kerf) of the cutting slot and the machining time were significantly affected by the air injection pressure and input energy. Moreover, it was also observed that there exists an optimal relationship between the machining time and input parameters including the air pressure and vibration frequency and amplitude. Central composite design based experiments were also carried out, and empirical models of the machining time and cutting slot kerf have been developed using the response surface methodology to analyze and optimize the process.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.8
• /
• pp.834-839
• /
• 2012

Recently, mechanical components with miniaturized size, complex shape and fine surface are on demand from industries such as mobile electronics, medical devices and defense. The size of them is smaller than several millimeters, the shape has micro-holes, curve, or multi-step and the surface is mirror-like. This features are not able to be machined with the conventional machining, therefore electro-discharge machining (EDM), cutting, and laser machining have been applied. If the technologies are assisted by vibration, high aspect ratio and good surface are to be achieved. In this paper, prior and current researches of vibration-assisted machining are reviewed. Machining mechanisms with vibration-assisting are explained, their effects are shown, and vibrating apparatuses are discussed. Especially, comparison between with and without vibration assisting is presented. This review shows the vibration-assisted machining is effectively fabricate the components with small and complicated shape and fine surface finish.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1871-1878
• /
• 2014

PMMA (Polymethyle-methacrylate) optical components have recently been increasingly used as one of the important part of the high precision equipments. This research presents comparatively the surface preparation of light incident plane, LIP (Light Incident Plane) of LGP (Light Guide Panel) by end milling, high speed shaping, and vibration assisted high speed shaping. From several experiments, the results show that the surface quality was improved in high speed shaping and the vibration assisted HSS show not only decreasing waviness and breakage also raising the straightness property. For applying high speed shaping and vibration assisted HSS, an additional tool post was developed and experimentally used.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.23-31
• /
• 2021

Surface texturing is a promising route to reduce the friction forces between two surfaces in sliding contact. To this end, the fabrication of micro dimples is one of the most widely used surface texturing methods. According to published results, textured surfaces with elliptical micro dimples offer the best friction performance. Therefore, we fabricated elliptical micro dimples on carbon steel (SM45C) by using dual frequency vibration assisted machining. High and low frequencies of 16.3 kHz and 230 Hz were applied to the 3D resonant elliptical vibrator. The 3D resonant elliptical vibrator with a triangular cubic boron nitride insert was assembled on a computer numerically controlled turning lathe. Oval micro dimples of various profiles were manufactured on carbon steel. In terms of the profile of the elliptical micro dimples, the experimental results indicated that the average micro dimple width and depth were 112 ㎛ and 7.7 ㎛. These dimensions are closely related to the cutting conditions and can be easily controlled.