• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.26-29
• /
• 1999

The I-V characteristics of the n-channel offset gated poly-Si TETs have been systematically investigated in order to analyse the effects of offset region. The on currents are reduced due to the series resistance by the offset length and there is no kink phenomenon in offset devices. The off currents of the offset gated TFTs are remarkably reduced to 10$^{-12}$ A independent of gate and drain voltage because the electric field is weakened by the increase of the depletion region width near the drain region. It is shown that the offset regions behave as a series resistance and reduce lateral and vertical electric field.

• Advances in concrete construction
• /
• 제16권2호
• /
• pp.79-89
• /
• 2023

The occurrence of unexpected horizontal offset in the instrument or target will result in accumulated horizontal deviation in segment alignment with traditional short-line match method. A geometry control method, the four-point method, is developed for precast segmental bridges to avoid the influences of unexpected horizontal offset. The concept of the four-point method is elucidated. Furthermore, the detailed instruments and instructions are introduced. Finally, the four-point method is validated through a practical engineering application. According to the survey data, after short-line match precast construction, the vertical deviations on both sides vary between -5 mm and 5 mm in almost all segments, and the horizontal deviations vary between -4 mm and 4 mm in all segments. Without on-site adjustment, the maximum vertical and horizontal closure gaps are 12.3 and 26.1 mm, respectively. The four-point method is suggested to alleviate the issues associated with relatively poor soil conditions in casting yard.

• Journal of Electrical Engineering and information Science
• /
• 제2권3호
• /
• pp.132-138
• /
• 1997

Electrical characteristics of split-gate flash EEPROM with triple polysilicon is investigated in terms of effects of floating gate and offset gate. In order to search for t the effects of offset gate on programming characteristics, threshold voltage and drain current are studied with variation of control gate voltage. The programming process is believed to depend on vertical and horizontal electric field as well as offset gate length. The erase and program threshold voltage are found to be almost constant with variation of control gate voltage above 12V, while endurance test indicates degradation of program threshold voltage. With increase of offset gate length, program threshold voltage becomes smaller and the drain source voltage just after program under constant control gate voltage becomes higher.

• 한국항행학회논문지
• /
• 제27권4호
• /
• pp.356-364
• /
• 2023

항행 정밀도 증가는 항공교통 수용량을 개선함으로써 효율적인 공역 환경을 조성하였으나, 항공안전 측면에서는 항공기 간 충돌확률을 증가시키는 요인으로 작용하였다. 항공기가 고도 분리에 실패하더라도 좌우 위치 오차를 갖는 경우 충돌로 이어지지 않지만, 좌우 위치 정밀도가 증가하면 위치 랜덤성이 줄어들어 항공기 충돌확률이 증가하게 된다. 이에 따라 국제민간항공기구는 항공기를 항공로 중심선으로부터 의도적으로 이탈시키는 SLOP (Strategic Lateral Offset Procedures) 절차를 도입하였으며, 우리나라 또한 이와 유사한 Offset 절차를 운영하고 있다. Y579 항공로는 22년 말 복선화되기 전까지 offset 절차로 운영되었으며, Y579 offset 항적 분석결과 SLOP 절차와 달리 단방향 복선 항공로와 유사함을 확인하였다. 본 논문은 단방향 복선 항공로 및 offset 절차에 적용 가능한 안전평가 방법론을 개발하고 이를 활용하여 Y579 Offset 절차에 대한 안전평가를 수행하였다.

• 구강회복응용과학지
• /
• 제18권4호
• /
• pp.301-311
• /
• 2002

The purpose of this study was to compare the distributing pattern of stress on the finite element models with the different vertical bone level of implant fixture. The two kinds of finite element models were designed according to vertical bone level around fixture ($4.0mm{\times}11.5mm$). The cemented crowns for mandibular first and second molars were made. Three- dimensional finite element model was created with the components of the implant and surrounding bone. Vertical loads were applied with force of 200N distributed within 0.5mm radius circle from the center of central fossa and distance 2mm and 4 mm apart from the center of central fossa. Von-Mises stresses were recorded and compared in the supporting bone, fixtures, abutment screws, and crown. The results were as following : (1) In vertical loading at the center circle of central fossa on model 1 and 2, the difference from vertical bone in implant placement did not affect the stress pattern on all components of implant except for crown. (2) With offset distance incerasing and the bone level of implant decreasing, the concentration of stress occured in the buccal side of long crown, around the buccal crestal bone, and on the fixture- abutment interface. As a conclusion, the research showed a tendency to increase the stress on the supporting bone, fixture and screw under the offset loads when the vertical level of bone around fixture was different. Since the same vertical bone bed has more benefits than the different bone bed around fixtures, it is important to prepare a same vertical level of bone bed for the success of implants under occlusal loads.

• 한국해양공학회지
• /
• 제28권2호
• /
• pp.160-166
• /
• 2014

Because of industrial development, industrial facilities are becoming more complex and diversified. Plant industries are focused on productivity improvement, cost reduction, and product uniformity by simplifying production processes using automated control. Furthermore, plant industries require higher pressures and temperatures to improve energy efficiency. For this reason, the valves used in plants are operated under harsh conditions. Globe valves and gate valves are mainly used for high pressure these days. However, these valves have various problems, including low maintainability and high cost, due to structural problems. Therefore, butterfly and ball valve applications are increasing in industrial plants. This paper suggests a quadruple-offset butterfly valve that is applicable to bi-direction use, and the principle design parameters are suggested. The selected design parameters are an eccentric flange center line and shaft centerline(Offset 1), an eccentric seat centerline and disc shaft centerline(Offset 2), the angle between the flange centerline and seat wedge angle(Offset 3), the angle between the vertical direction of the disc shaft centerline and seat centerline(Offset 4), and the seat engagement angle. To analyze the interaction effect of the design parameters, ANOM and ANOVA were performed with an orthogonal array. The parameters were found to have effects in the following order: Offset 2, Offset 1, engagement angle, Offset 3, and Offset 4. The interaction between the parameters was insignificant.

• 구강회복응용과학지
• /
• 제21권2호
• /
• pp.169-182
• /
• 2005

The purpose of this study was to compare the stress distribution around the surrounding bone according to the splinted and non-splinted conditions on the finite element models of the two implant crowns with the different vertical bone level. The finite element model was designed with the parallel placement of the two fixtures ($4.0mm{\times}11.5mm$) with reverse buttress thread on the mandibular 1st and 2nd molars. As the bone quality, the inner cancellous bone and the outer 2 mm cortical bone were designed, and the cortical and cancellous bone were assumed to be perfectly bonded to the implant fixture. The splinted model(Model 1) had 2 mm contact surface and the non-splinted model(Model 2) had $8{\mu}m$ gap between two implant crowns. Two group (Splinted and non-splinted) was loaded with 200 N magnitude in the vertical and oblique directions on the loading point position on the central position of the crown, the 2 mm and 4 mm buccal offset point from the central position. Von Mises stress value was recorded and compared in the fixture-bone interface in the bucco-lingual and mesio-distal sections. The results were as follows; 1. In the vertical loading condition of central position, the stress was distributed on the cortical bone and the cancellous bone around the thread of the fixture in the splinted and non-splinted models. In the oblique loading condition, the stress was concentrated toward the cortical bone of the fixture neck, and the neck portion of 2nd molar in the non-splinted model was concentrated higher than that of 1st molar compared to the splinted model. 2. In the 2 mm buccal offset position of the vertical loading compared to the central vertical loading, stress pattern was shifted from apical third portion of the fixture to upper third portion of that. In the oblique loading condition, the stress was distributed over the fixture-bone interface. 3. In the 4 mm buccal offset position of the vertical loading, stress pattern was concentrated on the cortical bone around the buccal side of the fixture thread and shifted from apical third portion of the fixture to upper third portion of that in the splinted and non-splinted models. In the oblique loading, stresses pattern was distributed to the outer position of the neck portion of the fixture thread on the mesio-distal section in the splinted and non-splinted models. Above the results, it was concluded that the direction of loading condition was a key factor to effect the pattern and magnitude of stress over the surrounding bone of the fixture under the vertical and oblique loading conditions, although the type with or without proximal contact did not effect to the stress distribution.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.1-9
• /
• 2008

This report contains the results of structural analysis for the verification of the optimum offset range on the top of T-Bar with stiffener and BKT using at DSME Offset range as $6.0{\sim}10.0mm$ based on the 3-D FE analysis and experimental results of angie type stiffener as described in Annex 1 has been used as yard standard over ten (10) years under all Classification approval. Recently, Owner and Class have requested the confirmation for the misalignment based on the Yard's Standard so that a couple of locations for LNGC and LPGC has been investigated the structural strength by FE method using the offset ranges from 0.0 to 18.0 mm.

• 한국군사과학기술학회지
• /
• 제24권3호
• /
• pp.255-263
• /
• 2021

This paper investigates numerically the effect of rotor hub vibratory load components on the airframe vibration responses of high-speed compound unmanned rotorcraft (HCUR) using a lift-offset coaxial rotor, wings, and two propellers. The rotor hub vibratory loads are predicted using a rotorcraft comprehensive analysis code, CAMRAD II, and the airframe vibration responses are calculated by a finite element analysis software, MSC.NASTRAN. It is shown that the vibratory hub pitch moment of a lift-offset coaxial rotor is the most dominant component for both the longitudinal and vertical vibration responses at four specified locations of the airframe.

• 소음진동
• /
• 제8권5호
• /
• pp.922-928
• /
• 1998

This paper presents the automatic alignment measuring system for improving the accuracy and working time of alignment of large vertical hydraulic pump turbine. It is general practice that rotating shaft should run within acceptable vibration limit. In order to obtain better run-out data of multi-stage rotor, careful and accurate alignment approach must be established. Generally, present alignment procedure are required several iterative works and so many manpower. Therefore, the new system has been developed using a vector calculation algorithm, laser sensor and data acquisition devices. As a result of appling to actual machines, it is confirmed that manpower is saved up to an average 90%.