• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.6
• /
• pp.1533-1545
• /
• 1996

In this paper, the design and implementation of echo canceller with new variable step size algorithm is discussed. The method used in the new algorithm is to periodically adopt the test function which helps an optimal coefficient tracking. This algorithm outperforms LMS and VS algorithms in convergence speed and steady state error. As the period of test function is decreased, the speed of convergence is improved, but the number of calculation is increased, then the trade off between these parameters must be considered. Simulation results show new algorithm outperforms LMS and VS algorithms in convergence rate. For the design of hardware, circuit is designed with VHDL, and synthesized with Act1 withc is a FPGA library of ActelTM in use of synovation of InterGraph$^{TM}$. Verification of the synthesized circuit is carried out with simulator DLAB. The circuit based on the algorithm which is suggested in this paper calculated 7 radix places of inary number. A simulation data for the verification is based on the data of algorithm simulation. When the same input data is applied to the both simulation, output results of circuit simulation had slight difference in compare with that of algorithm simulation. The number of used gate is about 5,500 and We have 5.53MHz in maximum frequency.y.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.501-504
• /
• 2004

This paper proposes degree of hydration based shrinkage prediction model of 40MPa HPC. This model shows degree of hydration which is defined as the ratio between the hydrated cement mass and the initial mass of cement is very closely related to shrinkage deformation. In this study, degree of hydration was determined by CEMHYD-3D program of NIST. Verification of the predicted degree of hydration is performed by comparison between test results of compressive strength and estimated one by CEMHYD-3D. Proposed model is determined by statistical nonlinear analysis using the program Origin of Origin Lab. Co. To get coefficients of the model, drying shrinkage tests of four specimen series were followed with basic material tests. Testes were performed in constant temperature /humidity chamber, with difference moisture curing ages to know initial curing time effect. Verification with another specimen, collected construction field of FCM bridge, was given in the same condition as pre-tested specimens. Finally, all test results were compared to propose degree of hydration based model and other code models; AASHTO, ACI, CEB-FIP, JSCE, etc.

• The Korean Journal of Franchise Management
• /
• v.11 no.3
• /
• pp.27-41
• /
• 2020

Purpose: This study was conducted for purpose to derive a model of the founding competency of undergraduate students preparing for job creation. We want to support undergraduate students who are preparing to start a job creation so that they can successfully start a job creation. In Korea, research on entrepreneurship competency has been actively conducted for a variety of subjects including undergraduate students, but research on job creation competency is insufficient. To this end, we intend to contribute to the success of undergraduate students preparing for job creation by deriving a job competency model. Research design, data, and methodology: In order to derive job creation competency, interviews were conducted with best practices in the job creation activity process, and the job creation competency was derived using Spencer and Spencer's competency model development process and competency dictionary. Result: The derived competencies were further supplemented through the verification of job creation experts and HRD experts, and a total of 3 competency groups, 13 competences, and 44 specific actions were derived. The derived job creation competency model is significant in that it is an initial study that attempts to develop job creation competency, that it can be a reference point for developing curriculum for undergraduate students preparing for job creation, and that they have developed a competency model in the new field of job creation. However, despite this significance, there are some limitations. First, the derived competency model did not perform validity verification using quantitative research. Second, the difference analysis between the excellent group and the average group was not conducted. Third, the level of behaviors could not be staged. Lastly, it was not possible to compare it with the competency of franchisor and job creation for undergraduate student competency. Therefore, it is necessary to upgrade the job creation competency model by conducting follow-up studies. The following is suggested as a follow-up study. First, verification of the validity of job creation competency, and second, a comparative study of excellent cases and average group. Third, a study on the level of action level of job creation competency. Lastly, it is a comparative study of job creation competency and the competency of franchise affiliates.

• Korea Trade Review
• /
• v.42 no.4
• /
• pp.93-114
• /
• 2017

Under the FTA agreement, preferential tariffs between FTA members will result in tariff reductions. In order to ensure the stable use of the FTA tariff system, it is necessary for the customs authorities to determine whether the origin goods are clearly applicable. This study analyzed the procedure of appeal according to the origin verification system based on the decision made by Korea Customs Service and Tax Tribunal. From this, we examined whether the rate of re-claiming a case rejected in the 'Review System of the Legality Before Taxation' differs. In addition, we carried out a quantitative analysis using bootstrapping technique in order to overcome the scarcity cases of verification of origin among FTA members. The implications of this paper are summarized as follows: First, we tested the hypothesis that the re-claiming rate of Western countries is higher. Second, some issues represented higher re-claiming rate. Third, there was no significant difference between the verification group and the re-claiming rate. Finally, even if an applicant makes a claim again, there is a possibility of being rejected again.

• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2018-2025
• /
• 2023

In our previous study, we proposed an integrated PG-PET-based imaging method to increase the prediction accuracy for patient dose distributions. The purpose of the present study is to experimentally validate the feasibility of the PG-PET system. Based on the detector geometry optimized in the previous study, we constructed a dual-head PG-PET system consisting of a 16 × 16 GAGG scintillator and KETEK SiPM arrays, BaSO₄ reflectors, and an 8 × 8 parallel-hole tungsten collimator. The performance of this system as equipped with a proof of principle, we measured the PG and positron emission (PE) distributions from a 3 × 6 × 10 cm³ PMMA phantom for a 45 MeV proton beam. The measured depth was about 17 mm and the expected depth was 16 mm in the computation simulation under the same conditions as the measurements. In the comparison result, we can find a 1 mm difference between computation simulation and measurement. In this study, our results show the feasibility of the PG-PET system for in-vivo range verification. However, further study should be followed with the consideration of the typical measurement conditions in the clinic application.

• The Korean Journal of Emergency Medical Services
• /
• v.21 no.1
• /
• pp.17-44
• /
• 2017

Purpose: This study aimed to identify the effects of cardiopulmonary resuscitation (CPR) training using a meta-analysis by effect size. Methods: The effect sizes for each variable and the overall effect size for the collected data were identified. The homogeneity verification of the effect size and the difference among the average effect sizes for each mediation variable were determined. Results: The overall average effect size for CPR training was 1.747. Homogeneity verification of the overall effect size was a Q-value of 3716.962, which was statistically significant (p=.000) when${\alpha}=.05$. CPR training showed statistically significant differences depending on age (p=.002), sex (p=.006), number of trainees (p=.000), research design (p=.000), training method (p=.027), and practical training tools (p=.000). Conclusion: CPR training can effectively improve knowledge, skills, and attitudes about CPR. The results of this meta-analysis contribute to the development of more effective educational guidelines for future CPR training and the advancement of the CPR education field.

• Korean Journal of Organic Agriculture
• /
• v.30 no.2
• /
• pp.171-189
• /
• 2022

This study analyzed the effect of purchase competence on purchasing performance when purchasing eco-friendly food ingredients from school nutrition teachers. To this end, 131 copies surveyed for school nutrition teachers in the survey area were used for analysis. As a result of the analysis, the verification of the difference between purchase competence and purchase performance according to the general characteristics of school nutrition teachers showed significant differences according to age. In addition, the general characteristics of nutrition teachers and the effect of purchase competence on purchasing performance had a positive (+) effect on purchasing performance by Attitude, Knowledge, and communication among purchase competence. In this respect, it is judged that it is necessary to form an organic relationship between the supplier of eco-friendly food ingredients and nutrition teachers in school meals.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.9
• /
• pp.72-80
• /
• 2019

In this task, the tool dynamometer design and manufacture, and the Ansys S/W structural analysis program for tool attachment that satisfies the cutting force measurement requirements of the tool dynamometer system are used to determine the cutting force generated by metal cutting using 3-axis static structural analysis and the LabVIEW system. The cutting power in a cutting process using a milling tool for processing metals provides useful information for understanding the processing, optimization, tool status monitoring, and tool design. Thus, various methods of measuring cutting power have been proposed. The device consists of a strain-gauge-based sensor fitted to a new design force sensing element, which is then placed in a force reduction. The force-sensing element is designed as a symmetrical cross beam with four arms of a rectangular parallel line. Furthermore, data duplication is eliminated by the appropriate setting the strain gauge attachment position and the construction of a suitable Wheatstone full-bridge circuit. This device is intended for use with rotating spindles such as milling tools. Verification and machining tests were performed to determine the static and dynamic characteristics of the tool dynamometer. The verification tests were performed by analyzing the difference between strain data measured by weight and that derived by theoretical calculations. Processing test was performed by attaching a tool dynamometer to the MCT to analyze data generated by the measuring equipment during machining. To maintain high productivity and precision, the system monitors and suppresses process disturbances such as chatter vibration, imbalances, overload, collision, forced vibration due to tool failure, and excessive tool wear; additionally, a tool dynamometer with a high signal-to-noise ratio is provided.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.26-32
• /
• 2020

There are many airline customer evaluation data, but they are insufficient in terms of predicting customer satisfaction in practice. In particular, they are generally insufficient in case of verification of data value and development of a customer satisfaction prediction model based on customer evaluation data. In this paper, airline customer satisfaction analysis is conducted through an experiment of correlation analysis between customer evaluation data provided by Google's Kaggle. The difference in accuracy varied according to the three types, which are the overall variables, the top 4 and top 8 variables with the highest correlation. To build an airline customer satisfaction prediction model, they are applied to three classification algorithms of Random Forest, SVM, DNN and conduct a classification experiment. They are divided into training data and verification data by 7:3. As a result, the DNN model showed the lowest accuracy at 86.4%, while the SVM model at 89% and the Random Forest model at 95.7% showed the highest accuracy and performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.9
• /
• pp.941-946
• /
• 2011

The Loran-C, a radio navigation system based on TDOA measurements is enhanced to eLoran using TOA measurements instead of TDOA measurements. Many error factors such as PF, SF, ASF, clock errors and unknown biases are included in eLoran TOA measurements. Because these error factors can cause failure in eLoran navigation algorithm, these errors must be compensated for high accuracy eLoran navigation results. Compensation of ASF and unknown biases are difficult to calculate, while the others such as PF and SF are relatively easy to eliminate. In order to compensate all errors in eLoran TOA measurements, a simple GPS aided bias compensation method is suggested in this paper. This method calculates the bias as the difference of TOA measurement and the range between eLoran transmitters and the receiver whose position is determined using GPS. The real data measured in Europe are used for verification of suggested method and navigation algorithm.