• Tunnel and Underground Space
• /
• v.22 no.5
• /
• pp.365-372
• /
• 2012

This paper aims to evaluate the effects that presence, installation number and capacity of ventilation vent and presence of multiple fire sources have on the behaviour of smoke temperature induced by vehicle fire in road tunnel. Six types of scenarios were assumed and FDS was ran to simulate them. As the number of ventilation vents increases, the smoke temperature are calculated to be reduced, but it is shown that effects exerted by two ventilation vents are almost similar to ones by three ventilation vents. Capacity of ventilation vent has a greater impact on the reduction of smoke temperature than installation number of ventilation vents. Smoke temperatures computed for all scenarios except for scenario No. 1 (without ventilation vent) and scenario No. 6 (with multiple fire sources) above fire source are analyzed to be under $400^{\circ}C$ and it means that the radiation of smoke layer above fire source doesn't induce the ignition of materials around fire source.

• Fire Science and Engineering
• /
• v.30 no.1
• /
• pp.6-11
• /
• 2016

This study analyzed the performance of smoke exhaustion installed to secure the life safety from the smoke each opening modes, as performing the simulation on the Jeju regions generating to strong windy using CONTAM. We assessed the effectiveness of the system under conditions of high external winds as well as an ambient wind conditions. It also assessed the relative effectiveness of opening all vents versus opening only those vents which served rooms in which the fire was located. This study revealed external winds exerted a substantial impact on the performance of the smoke ventilation system. It was found that opening the ventilation system in the room containing the fire resulted in a greater performance than opening vents in both fire in all rooms. The reduced performance of the smoke ventilation system upon the opening of all vents is thought to be due to the intrusion of outside air, and the establishment of unfavorable air circulation, caused by the negative pressure generated in the building.

• Corrosion Science and Technology
• /
• v.19 no.4
• /
• pp.189-195
• /
• 2020

Two air vents situated on a heat transport pipe in district heating system were exposed to the same environment for 10 years. However, one air vent was more corroded than the other. It also had a hole on the top of the front-end pipe. Comparative analysis was performed for these air vents to identify the cause of corrosion and establish countermeasures. Through experimental observation of the damaged part and analyses of powders sampled from air vents, it was found that corrosion was initiated at the top of the front-end pipe. It then spread to the bottom. Energy dispersive X-ray spectroscopy results showed that potassium and chlorine were measured from the corroded product in the damaged air vent derived from rainwater and insulation, respectively. The temperature of the damaged air vent was maintained at 75 ~ 120 ℃ by heating water. Rainwater-soaked insulation around the front-end pipe had been hydrolyzed. Therefore, the damaged air vent was exposed to an environment in which corrosion under insulation could be facilitated. In addition, ion chromatography and inductively coupled plasma measurements indicated that the matrix of the damaged front-end pipe contained a higher manganese content which might have promoted corrosion under insulation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1427-1435
• /
• 2001

Air movement in wokplaces, whether resulting from a forced ventilation system or naturally occurring airflow, has a significant impact on occupational health. In a huge shipbuilding factory building, typical harmful factors such as fume or vaporized gas from welding and cutting of steel plates, and dusts from grinding give unpleasant feeling. From field data survey, the yearly dominant, wind directions for the shipbuilding factory building tested were northwest, northeast and southeast Among the three wind directions, the ventilation improvement was the worst for the northeastern wind. This study was focused on location of the opening vents in order to utilize the natural ventilation effectively. Instantaneous velocity fields inside the 1/1000 scale-down factory building model were measured using a 2-frame PIV system. The factory building model was embedded in an atmospheric boundary layer simulated in a wind tunnel. The modified vents improve the internal Ventilation flow with increasing the flow speed more than two times, compared with that of present vents.

• Land and Housing Review
• /
• v.14 no.4
• /
• pp.111-120
• /
• 2023

Indoor air quality has become increasingly important with the increase in time spent in residential environments, impact of external fine dust, yellow dust, and the post-COVID 19 pandemic. Residential mechanical ventilation plays a key role in addressing indoor air quality. The legal standard for residential air changes per hour in Korea is 0.5 ACH. However, there are no standards for the location of supply and return vents. This study atempts to analyze the impact of ventilation performance based on the location of supply and return vents. An experiment was conducted using the CO₂ tracer gas concentration decay method in a mock-up house set inside a large chamber to minimize external influences. The experimental results indicated that the commonly used combination of 2 supply and 2 return vents in living room spaces had a lower mean age of air than the combination of 1 supply and 2 return vents. Using multiple supply and return vents had lower mean age of air than using just 1 supply and 1 return vent.

• 한국가시화정보학회:학술대회논문집
• /
• 2005.12a
• /
• pp.46-49
• /
• 2005

Vents at outer walls of a large factory building are very important for natural ventilation. But, if a full-open vent is used, rain comes through the vents. We tried to utilize the natural ventilation effectively using a louver. A 1/120 scale-down building model was placed inside an atmospheric boundary layer simulated in a wind tunnel test section. The effect of louver angle on the ventilation flow inside the factory building was investigated experimentally. Instantaneous velocity fields inside the building model were measured using a 2-frame PIV system with varying the louver angles ($\theta=20^{\circ},\;40^{\circ},\;60^{\circ}$). For the case of $\theta=60^{\circ}$, as the incoming flow into the factory building increases, the inside velocity distribution becomes uniformly.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.2
• /
• pp.376-381
• /
• 1990

An interactive computer program to design a mold cavity with the proper rigging system has been developed. In addition to the pattern and the risers generated in part 1 of this work, the various components of the gating system are generated in complete three dimensional models by a rational approach. Then they are laid interactively by the user, and united together with the pattern and the risers to result in the three dimensional model of the mold assembly. Finally, the vents and the mold box are constructed following the user's interactive specification and then the mold cavity is completed in a three dimensional geometric model by subtraction the mold assembly and the vents from the mold box. The three dimensional model of a mold cavity is useful for many related applications such as the solidification simulation for mold evaluation and the NC tool path generation for mold production.

• Ocean and Polar Research
• /
• v.22 no.1
• /
• pp.1-13
• /
• 2000

Chemoautotrophic symbiotic bacteria of organisms inhabiting the hydrothermal vent and cold seep communities in the deep-sea were histologically examined using a transmission electron microscopy on symbionts of Calyptogena sp. A from the site east off Miyako (water depth at 1,700m), Calyptogena sp. B from the Calyptogena Site, vestimentiferan tube worm Lamellibrachia sp. A from Sagami Bay Lamellibrachia sp. B from Calyptogena Site of the Iheya Ridge, pogonophoran tube worms from Sagami Bay and Calyptogena Site of the Iheya Ridge, Bathymodiolus spp. from Sagami Bay, the Iheya Ridge and the North Fiji Basin. Based on the morphological microscopic observations, two species of Calyptogena from Miyako and the Iheya Ridge, two species of vestimentiferan tube worms from Sagami Bay and the Iheya Ridge, and pogonophoran tube worms from Sagami Bay and the Iheya Ridge observed to host sulfur-oxidizing symbiotic bacteria. The occurrence of chemosynthetic symbionts in these organisms was expected beforehand based on the ecological observations of their habitats. Other members of these groups from the world oceans, and the recent advances in the symbiosis at vents and seeps were reviewed.

• Ocean and Polar Research
• /
• v.24 no.3
• /
• pp.215-223
• /
• 2002

Symbiosis of chemoautrophic bacteria with the members of hydrothermal vent and cold seep communities in the deep-sea were examined by histology using transmission electron microscopy; Bathymodiolus spp. from Sagami Bay, the Iheya Ridge and the North Fiji Basin; and Ifremeria nautilei from the North Fiji Basin. Two species of Bathymodiolus, each from Sagami Bay and the Iheya Ridge harbored methane-oxidizing symbionts within their gill tissues. Vent gastropod Ifremeria nautilei from the hydrothermal vents of the North Fiji Basin housed two types of symbionts; one sulfur-oxidizing type and the other methane-oxidizing type. The occurrence of chemosynthetic symbionts in these organisms were expected before-hand based on the ecological observations of their habit. The other members of these groups from world oceans and the recent advances in the symbiosis of the vent and seep communities were reviewed.

• Journal of the Korean Solar Energy Society
• /
• v.25 no.2
• /
• pp.71-79
• /
• 2005

In this study, the ventilation performance of mechanical ventilation system in apartment House was analyzed through model test according to characteristics of air-vent. Then adequate interval of air-vent was suggested using computer simulation which will create comfort environment through improvement of ventilation performance in apartment house. The result of experiment with separation plate to prevent mixture of contaminated exhaust air with fresh supply air, the ventilation efficiency improved about 10%. The result of simulation with horizontal location of exterior air-vent, contaminated exhaust air is mixed regardless of interval variation. Consequently, mixture of the exhaust air can be prevented through locating the supply air vent on the top side and exhaust air vent on the lower side.