• Wind and Structures
• /
• 제1권4호
• /
• pp.287-302
• /
• 1998

This paper formulates a probabilistic model which is able to represent the maximum instantaneous wind velocity. Unlike the classical methods, where the randomness is circumscribed within the mean maximum component, this model relies also on the randomness of the maximum value of the turbulent fluctuation. The application of the FOSM method furnishes the first and second statistical moments in closed form. The comparison between the results herein obtained and those supplied by classical methods points out the central role of the turbulence intensity. Its importance is exalted when extending the analysis from the wind velocity to the wind pressure.

• Wind and Structures
• /
• 제20권1호
• /
• pp.15-36
• /
• 2015

Characterization of wind flows over a complex terrain, especially mountain-gorge terrain (referred to as the very complex terrain with rolling mountains and deep narrow gorges), is an important issue for design and operation of long-span bridges constructed in this area. In both wind tunnel testing and numerical simulation, a transition section is often used to connect the wind tunnel floor or computational domain bottom and the boundary top of the terrain model in order to generate a smooth flow transition over the edge of the terrain model. Although the transition section plays an important role in simulation of wind field over complex terrain, an appropriate shape needs investigation. In this study, two principles for selecting an appropriate shape of boundary transition section were proposed, and a theoretical curve serving for the mountain-gorge terrain model was derived based on potential flow theory around a circular cylinder. Then a two-dimensional (2-D) simulation was used to compare the flow transition performance between the proposed curved transition section and the traditional ramp transition section in a wind tunnel. Furthermore, the wind velocity field induced by the curved transition section with an equivalent slope of $30^{\circ}$ was investigated in detail, and a parameter called the 'velocity stability factor' was defined; an analytical model for predicting the velocity stability factor was also proposed. The results show that the proposed curved transition section has a better flow transition performance compared with the traditional ramp transition section. The proposed analytical model can also adequately predict the velocity stability factor of the wind field.

• Fibers and Polymers
• /
• 제7권4호
• /
• pp.424-431
• /
• 2006

Roll drafting, a mechanical operation attenuating fiber bundles to an appropriate thickness, is an important operation unit for manufacturing staple yams. It influences not only the linear density regularity of the slivers or staple yams that are produced, but also the quality of the textile product and the efficiency of the thereafter processes. In this research, the dynamic states of the fiber bundle in the roll drafting zone were analyzed by simulation, based on the mathematical model that describes the dynamic behavior of the flowing bundle. The state variables are the linear density and velocity of the fiber bundles and we simulated the dynamics states of the bundle flow, e.g., the profiles of the linear density and velocity in the draft zone for various values of the model parameters and boundary conditions, including the initial conditions to obtain their influence on the dynamic state. Results showed that the mean velocity profile of the fiber bundle was strongly influenced by draft ratio and process speed, while the input sliver linear density has hardly affected the process dynamics. Velocity variance of individual fibers that could be supposed to be a disturbing factor in drafting was also influenced by the process speed. But the major disturbance occurred due to the velocity slope discontinuity at the front roll, which was strongly influenced by the process speed. Thickness of input sliver didn't play any important role in the process dynamics.

• 대한의용생체공학회:의공학회지
• /
• 제19권1호
• /
• pp.9-18
• /
• 1998

본 논문은 초음파 의용 영상에서 인체내의 매질의 초음파 속도의 불균일에 의한 focusing의 저하에 대하여 논하였다. simulation환경으로, 인체 내의 매질 중 속도 값이 가장 큰 차이가 나는 지방(fat)을 일정한 두께로 모델링하였다. 그리고 초음파 빔의 굴절에 의한 진행경로의 변화와 속도차이에 따른 시간지연에 의한 해상도 저하를 구하였다. 그리고 이를 보상하는 방법으로, 보상에 계산량이 많이 필요한 굴절을 무시하고, 속도차에 의한 시간지연만 보상하는 방법을 제안하였다. 제안한 방법을 적용할 경우 현재의 실시간 디지털 focusing 시스템에서 쉽게 구현 가능하다.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.50-56
• /
• 2006

Since most of small form-factor drives have a load/unload mechanism and the flying height of the head is getting lower as the capacity of disk drives increases, the load/unload velocity becomes one of the important factors to ensure the reliability of the load/unload mechanism. To control the load/unload velocity accurately, velocity sensing is essential. In this paper, we introduce a very practical method that acquires the load/unload velocity from the back electromotive force (BEMF) of a voice coil motor (VCM) and propose a calibration method for measuring the BEMF from a given circuit. Moreover, the effect of calibration error and temperature variation on the measurement of BEMF is shown by simulation. Then, this present method is applied to the load/unload velocity controller and is verified from the experimental result.

• 소성∙가공
• /
• 제13권3호
• /
• pp.225-229
• /
• 2004

Chemical Mechanical Polishing(CMP) process becomes one of the most important semiconductor processes. But the basic mechanism of CMP still does not established. Slurry fluid dynamics that there is a slurry film between a wafer and a pad and contact mechanics that a wafer and a pad contact directly are the two main studies for CMP. This paper based on the latter one, especially on the abrasion wear model. Material Removal Rate(MRR) is calculated using the trajectory length of every point on a wafer during the process time. Both the rotational velocity of a wafer and a pad and the wafer oscillation velocity which has omitted in other studies are considered. For the purpose of the verification of our simulation, we used the experimental results of S.H.Li et al. The simulation results show that the tendency of the calculated MRR using the relative velocity is very similar to the experimental results and that the oscillation effect on MRR at a real CMP condition is lower than 1.5%, which is higher than the relative velocity effect of wafer, and that the velocity factor. not the velocity itself, should be taken into consideration in the CMP wear model.

• 설비공학논문집
• /
• 제9권4호
• /
• pp.561-571
• /
• 1997

In this paper, the fundamental equations are developed for the pulsatile laminar flow generated by changing the oscillatory flow with $0{\leq}f{\leq}48Hz$ into a steady one with $0{\leq}Re{\leq}2500$ in a rigid circular pipe. Analytical solutions for the wave propagation factor k, the axial distributions of cross-sectional mean velocity $u_m$ and pressure p are schematically derived and confirmed experimentally. The axial distributions of centerline velocity and pressure were measured by using Pitot-static tubes and strain gauge type pressure transducers, respectively. The cross-sectional mean velocity was calculated from the centerline velocity by applying the parabolic distribution of the laminar flow and it was confirmed by using the ultrasonic flowmeter. It was found that the axial distributions of cross-sectional mean velocity and pressure agree well with theoretical ones and depend only on the Reynolds number Re and angular velocity $\omega$.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.252-257
• /
• 2007

The present study investigated the effect of air velocity on frost formation of slit fin-and-tube heat exchanger under frosting condition. The slit fin-and-tube heat exchanger with outer tube diameter 7.0mm and 1 row was used. Air side pressure drop, photographs of frost distribution, frost accumulation and frost thickness were presented with respect to the frosting time. In the early stage of experiment, the case with air velocity of 1.5m/s showed 403% higher for the air pressure drop than the case with the air velocity of 0.5m/s. As the frost was accumulated, the effect of air velocity on air pressure drop was decreased. In the end stage of test, air pressure drops of two cases were very close and air pressure drop for the air velocity of 0.5m/s was higher than that of 2.0m/s. It was also shown in the photographs of frost distribution, frost accumulation and frost thickness. From frost thickness, fanning friction factor was presented.

• 멤브레인
• /
• 제14권3호
• /
• pp.192-200
• /
• 2004

본 연구에서는 유기질막에 비해 안정성이 우수하고 사용수명이 긴 세라믹 막을 이용하여 혐기성 Lactobacillus 균주의 농축에 관해서 연구하였다. Cell harvesting (CH)에 영향을 주는 인자로 막투과 압력, 온도, 선속도 등에 대해 조사하였으며 세라믹 막을 이용하여 농축율 변화에 따른 플럭스와 TMP (transmembrane pressure)의 변화, 일정 VCF(volumetric concentration factor)에서 TMP변화 등의 최적조건에 관해 알아보았다. 그 결과 플럭스는 TMP, 선속도, VCF가 증가함에 따라 투과수량도 증가함을 알 수 있었다. 온도가 증가할수록 점도에 의해 초기 플럭스도 증가하지만 시간이 경과함에 따라 막 표면의 겔층의 형성으로 온도의 영향은 미미하였다. 또한 농축비 이하의 일정한 VCF에서 운전할 경우 플럭스가 안정적임을 알 수 있었다. 선속도 5 m/s, 공급액의 온도 $37^{\circ}C$, TMP 1 bar에서 6∼8 h 운전할 경우 PS 406 원액의 생균수는 4.9{\times}10^9$으로 약 8배 농축됨을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.127-134
• /
• 2008

교량의 거동은 교량의 지간 및 노면조도, 주행차량의 중량, 주행속도등 여러 요인들에 의해 달라지므로 교량의 동적거동을 정확히 예측하여 반영하기는 매우 어렵다. 우리나라 표준 시방 기준은 이러한 동적효과를 충격계수로 정의하고, 활하중에 충격계수를 곱하여 설계하중을 증가시키는 방법으로 동적효과를 고려하고 있다. 그러나 각 나라별로 충격계수를 적용하는 방법이 다르고, 아직까지도 명확하게 규명하지 못하고 있다. 그러므로 본 연구에서는 현재 사용 중인 PSC-I 거더교에 대하여 주행차량에 의한 동적 특성을 규명하기 위하여 동적재하, 정적재하, 의사정적재하시험을 이용하였다. 현장 재하시험에서 얻어진 결과를 통해 재하 속도에 따른 변위와 Strain관계를 찾을 수 있었으며, 이를 바탕으로 현재 논란이 있는 국내의 충격계수에 관한 경험식에 대하여 보다 합리적이고 실제적인 거동이 포함되도록 일조하는데 본 연구의 목적이 있다.