• 대한토목학회논문집
• /
• 제33권6호
• /
• pp.2267-2275
• /
• 2013

기존의 천수흐름 해석 상용모형에서는 내부 경계조건을 단순히 완전활동조건으로 가정하여 유체의 흐름을 해석함으로써 구조물 주위에서의 유속, 와도, 수위, 전단력의 분포, 항력 및 양력의 시간에 따른 변화 등을 올바르게 해석하지 못하였다. 본 연구에서는 구조물 주위에서의 흐름특성을 정확하게 예측할 수 있는 유한요소모형을 개발하고, 구조물에서의 경계조건을 활동길이를 이용한 부분활동조건으로 묘사하여 내부경계조건에 따른 원형 실린더 후면에서의 층류 흐름특성을 분석하였다. 종횡방향 유속 및 와도의 시간에 따른 변화, 후류길이, 활동길이에 따른 와류열의 변화와 질량보존율을 비교한 결과 완전활동조건을 부여한 경우에는 와류열이 전혀 형성되지 않고 완전한 층류흐름이 발생하였다. 부분활동조건을 입력한 경우 실린더 표면에서의 유속분포가 변화되어 전단력의 크기와 와도의 발생에 영향을 미치므로 무활조건을 부여한 경우에 비해 와류열의 발생 주기가 짧아졌다. 최대 질량보존 오차는 무활조건을 적용한 경우 0.73%로 나타났으며, 무활조건에 비해 부분활동조건을 부여한 경우의 오차율이 최대 0.21% 감소하였다.

• 대한인간공학회지
• /
• 제25권1호
• /
• pp.43-49
• /
• 2006

A laboratory study was conducted to evaluate if two different age groups(young vs. old) had differences in walking velocity and heel contact velocity and, furthermore, if these gait characteristics could adversely influence initial friction demand characteristics(i.e. RCOF) and the likelihood of slip-initiation. Twenty eight(14 younger and 14 older adults) participated in the study. While wearing a safety harness, all participants walked at their preferred gait speed for approximately 20 minutes on the linear walking track(1.5m× 20m) consisting of two floor-mounted forced plates. During subsequent 20 cameras, respectively. The results indicated that older adults walked slower(i.e., slower whole body center-of-mass velocity), exhibited lower heel contact velocity, and produced lower initial friction demand characteristics (i.e. RCOF) in comparison to younger adults. However, ANCOVA indicated that the diferences in heel contact velocity between the two age groups were due to the effects of walking velocity. The bivariate analysis further suggested that walking velocity was correlated to RCOF and heel contact velocity, while heel contact velocity was not found to be correlated to RCOF. In conclusion, could be a better indicator for predicting initial friction demand characteristics(i.e. RCOF) not hel contact velocity.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.111-115
• /
• 2002

The objective of this work is to develop improved slip factor model and correction method to predict flow through impeller in forward-curved centrifugal fan by investigating the validity of various slip factor models. Both steady and unsteady three-dimensional CFD analyses were performed with a commercial code tn validate the slip factor model and the correction method. The results show that the improved slip factor model presented in this paper could provide more accurate predictions for forward-curved centrifugal impeller than the other slip factor models since the presented model takes into account the effect of blade curvature. The comparison with CFD results also shows that the improved slip factor model coupled with the present correction method provides accurate predictions for mass-averaged absolute circumferential velocity at the exit of impeller near and above the flow rate of peaktotal pressure coefficient.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2007년도 추계학술대회
• /
• pp.84-87
• /
• 2007

Recently, many studies concern on the slip flow and slip length, which allow liquid flow to reduce drag force in microchannel. However, until now not enough investigation is performed experimentally to understand the slip flow in the superhydrophobic microchannel exhibiting riblet structures on vertical wall. Here we investigated and compared the slip flows according to the surface characteristics; hydrophilic, hydrophobic, and superhydrophobic wettabilities. Using the micro-PIV, velocity profiles can be obtained in the glass (hydrophilic), PDMS (hydrophobic), and micro-structured PDMS (superhydrophobic) microchannels. For both PDMS and superhydrophobic PDMS microchannels, we observed the slip effects showing the microscale slip lengths. Due to the micro-riblet, there are two distinctive flow characteristics on the riblet surface and the liquid meniscus in the valleys.

• 한국전산유체공학회지
• /
• 제14권2호
• /
• pp.46-51
• /
• 2009

The slip effect from the molecular interaction between fluid particles and solid surface atoms plays a key role in microscale fluid transport and heat transfer since the relative importance of surface forces increases as the size of the system decreases to the microscale. There exist two models to describe the slip effect: the Maxwell slip model in which the slip correction is made on the basis of the degree of shear stress near the wall surface and the Langmuir slip model based on a theory of adsorption of gases on solids. In this study, as the first step towards developing a general purpose numerical code of the compressible Navier-Stokes equations for computational simulations of microscale fluid flow and heat transfer, two slip models are implemented into a finite element numerical code of a simplified equation. In addition, a pressure-driven gas flow in a microchannel is investigated by the numerical code in order to validate numerical results.

• Journal of Mechanical Science and Technology
• /
• 제14권2호
• /
• pp.226-235
• /
• 2000

The performance prediction of an airfoil fan using a commerical code, STAR/CD, is verified by comparing the calculated results with measured performance data and velocity fields of an airfoil fan. The effects of inlet tip clearance on performance are investigated. The calculations overestimate the pressure rise performance by about 10-25 percent. However, the performance reduction due to tip clearance is well predicted by numerical simulations. Main source of performance decrease is not only the slip factor but also impeller efficiency. The reduction in performance is 12-16 percent for 1 percent gap of the diameter. The calculated reductions in impeller efficiency and slip factor are also linearly proportional to the gap size. The span-wise distributions of phase averaged velocity and pressure at the impeller exit are strongly influenced by the radial gap size. The radial component of velocity and the flow angle increase over the passsage as the gap increases. The slip factor decreases and the loss increases with the gap size. The high velocity of leakage jet affects the impeller inlet and passage flows. With a larger clearance, the main stream moves to the impeller hub side and high loss region extends from the shroud to the hub.

• Journal of applied mathematics & informatics
• /
• 제6권2호
• /
• pp.487-502
• /
• 1999

The hydrodynamic flow between two eccentric cylinders is examined for small values of modified Reynolds number porosity parameter and the non-dimensional slip velocity parameter in the presence of a radial magnetic field. The stream function and the pres-sure distribution are calculated and the results are presented graph-ically.

• Korean Chemical Engineering Research
• /
• 제58권2호
• /
• pp.307-312
• /
• 2020

최근 대기압이하 진공 압력 상태에서 운전되는 유동층 반응기는 진공건조 공정이나 플라즈마 화학증착과 같이 감압 유동화가 요구되기에 관심이 증대되어 왔다. 그러나 대기압 이하에서 운전되는 유동층의 수력학적 특성 연구는 많이 연구되지 않았다. 본 연구에서는 대기압 이하에서 운전하는 유동층의 압력강하를 층내 압력을 1.33 에서 101.3kPa 까지 변화시키며 측정하였다. 유동층의 운전 압력이 진공인 상태에서는 최소유동화속도가 압력이 감소함에 따라 증가하며, 이는 기체 밀도와 평균 자유경로 변화와 같은 slip 흐름에 의한 변화이다. 또한 기존의 상압 상태에서 운전되는 유동층의 최소유동화속도 상관식과 비교함으로써 압력 감소에 따른 slip 흐름의 영향 뚜렷하게 나타남을 가리키는 임계 Knudsen 수를 결정하였다. 이로부터 slip 흐름이 주도하기 시작하는 임계 압력을 실험적으로 결정하였다.

• 한국기계가공학회지
• /
• 제18권4호
• /
• pp.10-15
• /
• 2019

In this paper, we report a robust steering control using time delay control for the vehicle dynamics variation due to tire/road contact condition variation, the lateral disturbance force due to the side wind, and the yaw disturbance moment due to the difference between the left and right tires' pneumatic pressure. We controlled the side slip and yaw damping compensation for rapid steering at the high velocity of the vehicle. Based on the developed control, the driver can only consider the desired path without concerning on the vehicle dynamics variation, disturbances, and undesired side slip and yaw oscillations. Simulation results show that robustness from the vehicle dynamics variation and disturbances was achieved by using the developed time delay control. We evaluated the side slip and yaw damping compensation capability for the rapid steering at the high velocity of the vehicle in the cases of three control methods.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2585-2596
• /
• 1994

Many particle filled materials like Poweder/Binder mixtures for poweder injection moldings, have complicated rheological behaviors such as an yield stress and slip phenomena. In the present study, numerical simulation programs via a finite element method and a finite difference method were developed for the quasi-three-dimensional flows and the two-dimensional flow models, respectively, with the slip phenomena taken into account in terms of a slip velocity. In order to qualitatively understand the slip effects, typical numerical results such as vector plots, pressure contours in the cross-channel plane, and isovelocity controus for the down-channel direction were discussed with respect to various slip coefficients. Slip velocities along the boudary surfaces were also investigated to find the effects of the slip coefficient and processing conditions on the overall flow behavior. Based on extensive numerical calculations varying the slip coefficients, pressure gradient, aspect ratio, and power law index, the screw characteristics of the extrusion process were studied in particular with comparisons between the slip model and non-slip model.