• 소음진동
• /
• 제9권1호
• /
• pp.97-102
• /
• 1999

Structure-borne noise is an important aspect to consider during the design and development of a vehicle. In this work. it was desired to identify the primary paths associated with structure-borne noise generated from the engine and front suspension. An experimental source-path-receiver model was used to characterize the system. A variety of primary sources such as engine. tires or exhaust system generate vibrations of the inner surfaces of the passenger compartment of a vehicle which subsequently radiate noise. The source was characterized by the force acting at the engine-to-body interface. and the path was characterized by pressure over force FRF's. The excitation forces were indirectly determined using dynamic stiffness of rubber mount or the system accelerance matrix. Through these analysis, path contribution diagram which is well expressed primary noise path is obtained.

• 한국산학기술학회논문지
• /
• 제15권6호
• /
• pp.3357-3362
• /
• 2014

본 연구에서는 자동차가 노면을 주행 시 발생되는 진동에너지를 수집하여 차량의 배터리를 자가 충전할 수 있는 현가장치에 적용 가능한 공진형 선형 발전시스템을 설계하였다. 논문에서 제안된 선형 발전기는 기존의 발전기들과는 달리, 비교적 작은 에너지 원천인 노면의 진동에 더욱 효과적으로 대응하기 위해 공진 현상을 최대한 활용하는 설계를 지향했으며, 한정된 공간인 차량 현가장치에서의 선형 발전기의 발전 효과 검증 및 향후 연구 진행의 가능성을 판단하기 위해 수치해석적 방법을 활용하여 시스템의 동적 해석을 위한 기본 입력 속도를 도출하고 시스템의 목표인 발전 기능에 대한 예측을 위해 전자기 유한요소해석을 수행하였다. 본 연구에서 정상적인 발전 기능의 가능성을 확인한 공진형 선형 발전 시스템이 최근 자동차 산업의 큰 주축을 이루고 있는 하이브리드형 자동차 및 전기 자동차에 적용된다면, 각종 전장장치 및 배터리의 구동 및 성능유지에 도움을 줄 수 있을 것이다.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1508-1516
• /
• 2015

A single phase H-bridge inverter is employed in conventional Inductive Power Transfer (IPT) systems as the primary side power supply. These systems may not be suitable for some high power applications, due to the constraints of the power electronic devices and the cost. A high-frequency cascaded multi-level inverter employed in IPT systems, which is suitable for high power applications, is presented in this paper. The Phase Shift Pulse Width Modulation (PS-PWM) method is proposed to realize power regulation and selective harmonic elimination. Explicit solutions against phase shift angle and pulse width are given according to the constraints of the selective harmonic elimination equation and the required voltage to avoid solving non-linear transcendental equations. The validity of the proposed control approach is verified by the experimental results obtained with a 2kW prototype system. This approach is expected to be useful for high power IPT applications, and the output power of each H-bridge unit is identical by the proposed approach.

• Wind and Structures
• /
• 제20권2호
• /
• pp.275-292
• /
• 2015

The presence of traffic on a slender long-span bridge deck will modify the cross-section profile of the bridge, which may influence the flutter derivatives and in turn, the critical flutter wind velocity of the bridge. Studies on the influence of vehicles on the flutter derivatives and the critical flutter wind velocity of bridges are rather rare as compared to the investigations on the coupled buffeting vibration of the wind-vehicle-bridge system. A typical streamlined cross-section for long-span bridges is adopted for both experimental and analytical studies. The scaled bridge section model with vehicle models distributed on the bridge deck considering different traffic flow scenarios has been tested in the wind tunnel. The flutter derivatives of the modified bridge cross section have been identified using forced vibration method and the results suggest that the influence of vehicles on the flutter derivatives of the typical streamlined cross-section cannot be ignored. Based on the identified flutter derivatives, the influence of vehicles on the flutter stability of the bridge is investigated. The results show that the effect of vehicles on the flutter wind velocity is obvious.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.419-425
• /
• 1988

본 연구에서는 노면의 요철에 의한 차량의 동적반응을 구할 수 있도록 국내의 소형 승용차를 모델로 현가장치의 비선형성을 고려한 전체 10 자유도의 동역학적 모델 을 개발하였다. 모델을 개발함에 있어서 기본적으로 실차의 모든 요소들을 모델링하 려고 노력하였으며 그 이유는 본 연구에서 개발된 모델이 실차의 현가장치 부품 설계 에 사용되도록 하기 위함이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1127-1132
• /
• 2003

Suspension system of vehicle have enough endurance during its life time to protect passenger. Spring is one of major part of vehicle. Thus, a fatigue strength evaluation for leaf spring based on road load response was carried out. At first, strain of leaf spring is measured on the city condition and proving ground condition. And next, the damage analysis of road load response data was carried out. And fatigue test of leaf spring were also carried out. Based on -N life relation, fatigue life of leaf spring was evaluated at belgian mode, city mode and drawing test specification. After that, it is compared the design life of leaf spring and evaluated fatigue life by belgian mode, city mode and drawing test specification. From the above, the maximum load-fatigue life relation of leaf spring was defined by test. and new test target of belgian mode and city mode was proposed to accept design specification of leaf spring. It is expect that proposed test target can verify leaf spring fatigue endurance at specific road condition.

• 한국CDE학회논문집
• /
• 제21권4호
• /
• pp.409-416
• /
• 2016

This study aims to investigate dynamic interaction characteristics between Maglev train and 3 span continuous guideway. The integrated model including a 3D full vehicle model based on multibody dynamics, flexible guideway by a modal superposition method, and levitation electromagnets with the feedback controller is proposed. The proposed model was applied to the Incheon Airport Maglev Railway to analyze the dynamic response of the vehicle and guideway from the numerical simulation. Using field test data of air gap and guideway deflections, obtained from the Incheon Airport Maglev Railway, the analysis method is verified. From the results, it is confirmed that Maglev railway system are designed and constructed safely according to the design criteria.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.91-96
• /
• 2001

When it is considered that many vehicle rides on the road and ride quality is an important method to evaluate vehicle performance with handling, running-over-bump manoeuvre may be suitable for testing ride quality. In this paper, a computed model has roughly steering system and lumped mass, connected by joint each rigid body, and suspension that has beam elements and has shock absorber as force element to represent nonlinear characteristics. A computer simulations for passing over a bump were made with two velocities. One side of vehicle passed over bump in due consideration of driver's habit that driver is subject to avoid a bad ride quality. On simulation, vertical acceleration, pitch angle and roll angle were measured at the mass center of chassis each case.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.84-92
• /
• 1997

Among the various sources of vehicle interior noise, this paper concerns the road induced noise ; the identification of its transfer path by using experimental method. Multiple input and single output model is taken as a noise generation model. Because it is impossible to measure the road imput forces directly, the acceleration signals are measured on four axle;three directions for each point. By considering the cross correlations of input signals, four uncorrelated source groups are taken. Multiple coherence function is employed to investigate the contribution of each group. In addtion, to identify the detailed path through the suspension systems, the contributions of all possible paths are ranked by using the coherence functions between interior noise and the relative accelerations of connections such as bushings and mountings. Measurements are performed with passenger vehicle traveling on concrete and asphalt roads at 60㎞/h.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.102-112
• /
• 1998

Shock absorber has a great influence on the performance of the vehicle(ride comfort, manipulation, noise, vibration, turning, stability). Therefore, in this study we consider theoretically about general damper, variable damping oil damper, the control of vehicle Characteristics for the suspension, and undesirable phenomenon. And we measured the vibration/noise characteristics of shock absorber for the real car experimentation, strain change, and noise characteristics of shock absorber using experimental equipment. The study of domestic company and research institute on the vehicle shock absorber is active, but that of basis is not. So we think that they should be accomplished actively. Therefore, this paper will develop theoretical system on the vibration/noise characteristics of shock absorber by theoretical consideration and experimental result analysis of dynamic characteristics of shock absorber that were accomplished in this study. Then we will use it as the optimistic design data for shock absorber development.