• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.31 no.3
• /
• pp.373-385
• /
• 2021

To provide convenience and safety of drivers, the recent vehicles are being equipped with a number of electronic control units (ECUs). Multiple ECUs construct a network inside a vehicle to share information related to the vehicle's status; in addition, the CAN protocol is normally applied. As the modern vehicles provide highly convenient and safe services, it provides many types of attack surfaces; as a result, it makes them vulnerable to cyber attacks. The automotive IDS (Intrusion Detection System) is one of the promising techniques for securing vehicles. However, the existing methods for automotive IDS are able to analyze only periodic messages. If someone attacks on non-periodic messages, the existing methods are not able to properly detect the intrusion. In this paper, we present a method to detect intrusions including an attack using non-periodic messages. Moreover, we evaluate our method on the real vehicles, where we show that our method has 0% of FPR and 0% of FNR under our attack model.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.256-258
• /
• 2016

Domestic vehicle demand is growing steadily. In proportion to the increased interest generated by the automobile-related accidents are more frequent. One of the causes of these accidents are caused by vehicle accidents exists tire problems. Users check tire wear with their naked eyes or check the tread and the wear indicator by using a coin. However, such visual judgment cannot be precise and make it possible to identify the time for tire replacement. Therefore, by utilizing visual and objective data rather than incorrect decisions through objective data, we designed a system that accurately and can easily tell whether the tire condition and replacement of the driver.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.953-955
• /
• 2004

This paper describes the information transmission method using communication networks between Remote Terminal Unit(RTU) and Protection and Control system(PCU) of the direct current switchgear for Light Railway Vehicle, and also represents the test result, which carried out in the laboratory. In this test, transmission signal waveform, polling time, response time and request/response frame were measured between RTU and PCU. The field test including the measurements of analog signal and status of the digital logic operation of PCU will be conducted in near future.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.2
• /
• pp.325-336
• /
• 2023

With the development of autonomous driving technology, the number of external contact sensors mounted on vehicles is increasing, and the importance is also rising. The vehicular ultrasonic sensor uses the LIN protocol in the form of a bus topology and reports a status message about its surroundings through the vehicle's internal network. Since ultrasonic sensors are vulnerable to various threats due to poor security protocols, physical testing on actual vehicle is needed. Therefore, this paper developed a LIN-CAN co-analysis testbed with a jig for location-specific distance test to examine the operational relation between LIN and CAN caused by ultrasonic sensors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.490-492
• /
• 2021

In order to realize a safety society in traffic accidents, Korea prepared comprehensive government-wide measures in 2017. Efforts are being made to minimize accidents while walking by children and the elderly by lowering the speed limit in urban areas from 60 km to 50 km and limiting the vehicle to 30 km in the case of child protection zones. In this study, after pre-processing each data with the status of vehicle registration and traffic accident spatial data (GIS) by designating a specific area, Danyang-gun, where the rate of child traffic accidents is increasing every year, it is intended to understand the structure of the data and find out the structural pattern of the data analytical studies were conducted.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.9
• /
• pp.133-141
• /
• 2021

The development and demand for the system that provides users with traffic information and efficient road use have continued. also, this system provides the basic technology of the Intelligent Transport System (ITS). The most used traffic information collection tools are Vehicle detectors (VDS) and short-range wireless communication (DSRC) on express way. In order to generate reliable traffic information, it is necessary to efficiently manage and utilize the collected data as well as high-quality traffic data collection and processing technology. In this study, traffic information collection·processing·provision systems were investigated, and analyze the current status and problems of traffic information collected through VDS. Based on this, we would like to present an improved collection algorithm that utilizes the Kalman filter for vehicle information measurement of VDS data. By using the algorithm of this study, it is possible to minimize the time delay of the estimated value as well as the noise removal that inevitably occurs during measurement.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.1
• /
• pp.71-76
• /
• 2002

Because the driving time is increased under the low speed by rapidly increasing of vehicles, this paper is presented a new ignition control system for improvement the fuel economy, which only some of cylinders are using under the idle status or low speed and preserving the engine rpm. is applicable to effective in fuel economy. An actual hardware was made to prove this new control system. The developed variable cylinder engine concentrated the heat neat the cylinders in idle status or low speed, so there was a problem in re-ignition. It was the reason of a lot of exhaust gas, high fuel consumption and instability of engine revolution. In this paper, in order to solve above problem to show the improvement fuel economy using the new ignition control system and valve opening period at idle status of low speed.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.8
• /
• pp.9-21
• /
• 2022

In this paper, we developed a 100% detection system for entering and leaving vehicles by improving the detection rate of existing detection cameras based on the LiDAR sensor, which is one of the core technologies of the 4th industrial revolution. Since the currently operating parking lot depends only on the recognition rate of the license plate number of about 98%, there are various problems such as inconsistency in the entry/exit count, inability to make a reservation in advance due to inaccurate information provision, and inconsistency in real-time parking information. Parking status information should be managed with 100% accuracy, and for this, we built a parking lot entrance/exit detection system using LIDAR. When a parking system is developed by applying the LIDAR sensor, which is mainly used to detect vehicles and objects in autonomous vehicles, it is possible to improve the accuracy of vehicle entry/exit information and the reliability of the entry/exit count with the detected sensing information. The resolution of LIDAR was guaranteed to be 100%, and it was possible to implement so that the sum of entering (+) and exiting (-) vehicles in the parking lot was 0. As a result of testing with 3,000 actual parking lot entrances and exits, the accuracy of entering and exiting parking vehicles was 100%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.148-156
• /
• 2003

Many car manufacturers have frequently adopted an aggressive inflator and a lower threshold speed for airbag deployment in order to meet an injury requirement for unbolted occupant at high speed crash test. Consequently, today's occupant safety restraint system has a weakness due to an airbag induced injury at low speed crash event. This paper proposes a new crash algorithm to improve the weakness by suppressing airbag deployment at low speed crash event in case of belted condition. The proposed algorithm consists of two major blocks-crash severity algorithm and deployment logic block. The first block decides crash severity with two levels by means of velocity and crash energy calculation from acceleration signal. The second block implemented by simple AND/OR logic combines the crash severity level and seat belt status information to generate firing commands for airbag and belt pretensioner. Furthermore, it can be extended to adopt additional sensor information from passenger presence detection sensor and safing sensor. A simulation using real crash data for a 1,800cc passenger vehicle has been conducted to verify the performance of proposed algorithm.

• KIPS Transactions on Computer and Communication Systems
• /
• v.1 no.2
• /
• pp.71-78
• /
• 2012

The digital tachograph is a device that automatically records speed and distance of a vehicle, together with the driver's activity and vehicle status at an accident. It records vehicle speed, break status, acceleration, engine RPM, longitude and latitude of GPS, accumulated distance, and so on. European Commission regulation made digital tachographs mandatory for all trucks from 2005. Republic of Korea made digital tachographs mandatory for all new business vehicles from 2011 and is widening the range of vehicles that must install digital tachographs year by year. This device is used to analyze driver's daily driving information and car accidents. Under a car accident that makes the device reliability unpredictable, it is very important to store driving information with maximum reliability for its original mission. We designed and implemented a practical digital tachograph. This paper presents a storage scheme that consists of a first storage device with small capacity at a high reliability and a second storage device with large capacity at a low cost in order to reliably records data with a hardware at a low cost. The first storage device records data in a SLC NAND flash memory in a log-structured style. We present a reverse partial scan that overcomes the slow scan time of log-structured storages at the boot stage. The scheme reduced the scan time of the first storage device by 1/50. In addition, our design includes a scheme that fast stores data at a moment of accident by 1/20 of data transfer time of a normal method.