• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.111-119
• /
• 2011

The noise prediction model, KRON-2006, in South Korea has been developed for obtaining the average noise level. The model is based on an outdoor sound propagation method based on ISO9613 and ASJ Model-1998 and supports the analysis of the linear noise source, such as highway, for obtaining Leq. Because of that, the model can't obtain Lmax, Lmin from the time series noise profile based on traffic at every moment. In order to address this problem, the real time noise prediction model based on traffic simulation using GIS model and algorithm is proposed. It can predict the vehicle point noise level based on vehicle type, speed generated from traffic simulation by using headway and obtain Lmax, Lmin as integrating the noise profile generated from it at every moment. An evalution of the noise prediciton model using field measurements finds good agreement between predicted and measured noise levels at 1m, 8m, 15m from curb of the near side lane.

• Journal of Korean Society of Transportation
• /
• v.35 no.4
• /
• pp.261-277
• /
• 2017

This study defines influencing sections as the part of the road section where passing vehicles are traveling with the lower speed compared to speed limit due to speed humps. The influencing section was divided into 3 parts; influencing section before the speed hump, interval section, and influencing section after the speed hump. This analysis focused on the changes of each part depending on installation types, vehicle types, and daytime or nighttime. For the interval section, especially, the ratio of distance traveled with lower speed than speed limit to interval section is defined as effective influencing section ratio to be analyzed. Vehicle speed profiles were collected with a speed gun to extract influencing section lengths. The survival analysis was applied and estimated survival functions are compared with each other by several statistical tests. As a consequence, the average length of influencing section on the 50m sequential speed humps was 75.3% longer during the deceleration than that of isolated speed hump, and 18.9% during the acceleration. The effective influencing section ratio for the 30m and 50m sequential speed humps had a small difference of 81.0% and 76.0% while the absolute values of the section that passing speed were less than the speed limit were longer on 50m sequential speed humps, each being 24.3m and 38.0m. Using the log rank test, it was evident that sequential speed humps were more effective to increase the length of influencing sections compared to the isolated speed hump. Vehicle type was the strong factor for influencing section length on the isolated speed hump, but daytime or nighttime was not the effective one. This research result can be used for improving the efficiency selecting the installation point of speed humps for road safety and estimating the standard of the distance between sequential speed humps.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.606-612
• /
• 2008

Creep force is one of the only appeared at conventional train which used to be driven by metallic wheel and rail contact. Due to the elastic deformation of wheel/rail contact patch by the weights of wheel and all the components related to it, creep force generates and becomes to the decision factor of critical speed of bogie(or railway vehicle) which is the criteria of avoiding vehicle to be unstable. There are many kind of factors which affect generation of creep force at a wheel/rail contact surface such as viscosity of contact patch, velocity, wheel and rail geometric profile, mechanical properties of wheel and rail. This paper concentrates on a wheelset simple 2 DOF Equation of Motion being exerted. From the simple numerical analysis using linear solution about getting creep force some factors could find roughly. Among the factors geometric parameter could be the one of most important for this study. In the future we'll prolong the range of study to find out method of measuring creep force easily.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.135-144
• /
• 2008

The dynamic loads imposed by moving vehicles have variations in the magnitude due to the surface roughness of the pavement systems and the larger dynamic loads than the design loads may affect the pavement performance. This paper presents variations of the moving dynamic vehicle loads due to the pavement surface roughness. This study was performed as a basic study to apply the pay factor to the surface roughness for the improvement of pavement quality and performance. The profile data was obtained from the old and new pavements and the analysis was performed to investigate the dynamic loads when vehicles move on the pavements having those profiles. The artificial profiles were also developed to find the effects of the vehicle speed, wavelength and amplitude of the surface roughness on the dynamic vehicle loads. The increase in the load magnitude due to the surface roughness affects the stresses and strains of pavements and finally reduces the pavement life. The methodology to obtain the relationship between the surface roughness and the pavement performance was proposed in this study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.177-182
• /
• 2007

The effects of three fuselage head shapes and nonplanar ground surface on the aerodynamic characteristics of FAST fuselages are investigated using a boundary element method. Wind tunnel test is also performed to validate the present method and to identify the wall effect on the frictional drag which cannot be analyzed using the present method. It is found that the channel has an effect of increasing the lift of those investigated fuselages. The optimal head shape depends on the design conditions of the FAST and its guideway channel. Comparing the calculated induced drag with the measured total drag, it can be concluded that the profile drag is independent of the ground height. Thus, the present numerical method can be applied to the conceptual design of the high-speed ground transporters if only the profile drag of the vehicle in free flight is assumed to be known.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.7-15
• /
• 2009

This paper introduces a new variable valve actuation mechanism with movable second cam center. Valve lift and open duration can be continuously varied according to engine speed and load conditions. A new method to analyze the kinematic relations between the first and second cam profiles and valve motion are also introduced. Because of rocker motion of the second cam, conventional motion conversion program could not be used in this problem. An example shows continuous variations of valve motion and adequate ramp incorporation throughout all valve lift modes. Valve acceleration profile at the high lift mode is similar to that of conventional valvetrains. Contact geometry analysis of the mechanism gives basic information on the load conditions between the components.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2001.02a
• /
• pp.16-21
• /
• 2001

The ride quality of agricultural tractor seats is evaluated based on the vibration of the human bodies. Tractor ride vibration levels have been measured at the person-seat interface along 7 axes(3 translational axes at the feet, 3 translational axes on a seat surface and 1 axis at the seat back), under different operating conditions. Since one of the most important parameters for ride comfort is the level and duration of the root mean square acceleration experienced, the ride values, such as the seat effective amplitude transmissibility, the component ride value, and the overall ride value based on acceleration root mean square are evaluated for a conventional tractor using frequency weighting functions and axis multiplying factors. The ride indices are also studied considering to the variation of vehicle speed and road profile.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.889_890
• /
• 2009

Design of high efficiency Switched Reluctance Motor (SRM) for Low Speed Electric Vehicle (LSEV) is presented in this paper. The design is made from point of view to save more used energy for operating LSEV. Focus on saving the energy gives more efficiency can be produced. Based on applying suitable driving cycles and investigates the frequently power used are foundation to design the proposed motor. Meanwhile through Finite Element Analysis (FEA) characteristic of the proposed motor such as inductance and torque profile can be obtained.

• Journal of the Korean Society for Railway
• /
• v.9 no.5 s.36
• /
• pp.618-623
• /
• 2006

Understanding the contact between wheel and rail is a starting point in railway vehicle dynamic research area and especially analysis for the contact geometry between wheel and rail is important. On the one hand, the critical speed as the natural characteristics of rolling-stock is generally tested on the roller rig. The geometrical characteristics of the wheel/roller contact on the roller rig are different from these of the general wheel/rail contact because the longitudinal radius of roller is not infinite compared with rail. Thus, in this paper we developed the algorithm to analyze the wheel/roller contact geometry of our roller rig which is constructed now and analyzed the difference between whee/roller contact and wheel/rail contact. In conclusion, we found that the yaw motion of wheelset and the roller radius influence the geometrical contact parameters in wheel flange contact area.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.33-38
• /
• 2010

As for an oil hydraulic vane pump of vehicle hydraulic systems, the highest of planning technique required by the acquisition of optimum profile data which can be available to predict noises and vibrations. Pressure pulsation may result in considerable vibration and noise of pump component as well as cavitation in hydraulic system. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in chamber surrounding a vane have been investigated. It is very important to predict pressure pulsation in vane pump. This paper presents analysis of technique of vane pump for automatic transmission. The predicted result using AMESim model were good agreement with the experimentally obtained results.