• 소음진동
• /
• 제5권2호
• /
• pp.197-206
• /
• 1995

Microphone array is designed to measure the equivalent source height of vehicle noise. The equivalent source position is defined for an arbirary distribution of acoustic sources above a perfectly reflecting plane and a microphone array for its measurement is developed. The normalized errors of the measured equivalent source heights are defined including the effects of background noise, the geometric near field, and source size. Normalized errors of the measured source heights obtained by a nemerical simulation for each parameter lead to optimization of the microphone spacing and to the design of an array which gives the equivalent source height as a function of frequency. The performance of the designed array is verified using the stationary loudspeaker experiments.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.911-915
• /
• 2004

Recently, several experimental techniques for identifying the noise sources distributed over a moving vehicle are being developed and used in order to design a low noise vehicle. The beamforming method, which uses phase information between several microphones to localize the source position, is proved to be one of the promising techniques applicable even under complicated test environments. In this study a beamforming algorithm is developed and applied to measure the dominant noise sources on a passenger car moving at constant speed. Unlike the acoustic signals from a stationary noise source, the sound generated from a moving source is distorted due to the Doppler effects. The sound pressure are measured with an spiral array system composed of 26 microphones and a pair of photo sensors are used to measure the. vehicle speed. The information about the speed and relative position of the vehicle are used to eliminate the Doppler effects from the measured pressure signal by using a de-Dopplerization algorithm. The noise generated from a moving vehicle can be grouped in many ways, however, tire noise and the noise generated from the engine are distinguishable at the speeds being tested.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.789-792
• /
• 2005

The dominant noise sources of Diesel Multiple Units are powerpack, which is composed of engine, transmission and cooling system, noise and wheel-rail rolling noise. The interior noise of a running vehicle is determined by structure-borne noise and air-borne noise from these noise sources. The contributions of interior noise from each noise source are calculated by air-borne transfer functions and structure-borne transfer functions of noise sources. In this paper, source separation technique is proposed to determine these transfer functions from the results of stationary and running tests of existing vehicle. With this technique, it is possible to get hold of contributions of interior noise from .noise sources of running vehicle. This source separation technique makes it possible to take efficient measures for reduction of interior noise at the early car-development stage.

• 지역연구
• /
• 제6권1호
• /
• pp.57-68
• /
• 1990

The purpose of this study is to develop the models to predict the noise PCE (Passenger Car Equivalence) of large running vehicles through noise prediction models. The noises were measured at the distance of 7.5M, 11.0M, and 14.5M from the noise source with test vehicles running at the speed of 40 Km/h, 60 Km/h, and 80 Km/h while normal traffic were detoured. Total noise levels were measured while vehicles were running at given speeds, Engine noise level was considered as the noise of its idle running at the three vehicle speeds shown above friction noise level was ascertained by moving the vehicle at given speeds without the engin operating. The noise prediction models for each noise source were developed by factors which affect to the each noise level. As a result of this paper, the reduction of total vehicle noise by increasing the distance to the noise source from 10 M to 15 M is as much as that by dropping its speed from 60 Km/h to 40 Km/h. Also, the reduction of PCE of total noise of large vehicle by making the noise source to that by reducing its speed from 80 Km/h to 60 Km/h. Enging noise PCE, which is in range between 65 and 160, is larger than friction noise PCE which is in range 3.5 and 5.5. Engin noise is the main noise of the large vehicles while friction noise is that of the small vehicles. Machine noise for large vehicles, and engin noise for small vehicles should be tightly controlled to reduce the vehicle noise. A low noise engine and tire, and the shape of vehicle body are needed to be developed to reduce noise further.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.105-108
• /
• 2005

The radiated noise from the automotive intake system should be predicted at the design stage. To this end, the precise measurement of in-duct acoustic source parameters of the intake system, i.e., the source strength and source impedance, is essential. Most of previous works on the measurement of acoustic source parameters were performed under a fixed engine speed condition. However, the requirement of vehicle manufacturer is the noise radiation pattern as a function of engine speed. In this study, the direct method was employed to measure the source parameters of engine intake system under a fixed engine speed and engine run-up condition. It was noted that the frequency spectra of source impedance hardly changes with varying the engine speed. Thus, it is reasonable to calculate the source strength under the engine run-up condition by assuming that source impedance is invariant with engine speed. Measured and conventional source models, i.e., constant pressure source, constant velocity source, and non-reflective source, were utilized to predict insertion loss and radiated sound pressure level. A reasonable prediction accuracy of radiated sound pressure level spectra from the intake system was given in the test vehicle when using the measured source characteristics which were acquired under the operating condition.

• 한국소음진동공학회논문집
• /
• 제26권7호
• /
• pp.774-780
• /
• 2016

In this paper noise source and transfer path of tactical vehicle are analyzed with partial coherence function and spectrum analysis. Engine, transmission, structure panel and aerodynamic are main source of cabin noise. To reduce cabin noise, identifying transfer path of sources and analyzing their contribution is important. With modeling of transfer path and partial coherence function, transfer path and principal noise source can be identified. Engine/transmission and structural resonance are principal source of low frequency noise and by adding stiffener and sound absorbing material, resonance of vibration and inflow air problem can be solved.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.125-129
• /
• 2003

The identification of location and strength distribution of extended noise sources is important in the practical noise control engineering, especially in the viewpoint of dealing with the inherent nature of noise problem in question. For noise source ranking inside an automotive vehicle, the window method has been mainly used due to its simplicity. However, time and cost drawbacks in the measurement and inaccuracy due to low-frequency tunneling and lack of phase information have been a serious problem in using this method. In this study, the inverse FRF method was employed to carry out the noise source ranking inside an automotive vehicle and it was also used to predict the interior sound pressure with the change of sound insulation materials. As a result, it was found that the source contribution of vehicle panels could be successfully identified in comparison with the window method. The sound pressure at driver's ear position was predicted based on the obtained data and was compared with the measured data. The agreement in spectral trends was acceptable and their difference in level was within 3㏈ above 500㎐.

• 한국음향학회지
• /
• 제35권4호
• /
• pp.310-318
• /
• 2016

본 연구는 해상 운항체에서 발생하는 소음원의 위치를 3차원적으로 추정하는 방법에 대해 다루었다. 해상 운항체인 선박이나 잠수함의 내부에 존재하는 소음원과 같이 근접이 어려운 경우라도 상대적으로 이동한다면 외부의 수중청음기에 수신된 신호는 도플러 효과가 발생한다. 본 연구에서는 이동 물체에 의한 도플러 효과를 바탕으로 소음원의 3차원 위치 추정 알고리즘을 제안하였다. 해상 운항체의 알고 있는 위치에 추가의 음원을 설치하여 예상되는 도플러 중심의 범위와 최단 접근점의 범위를 점차 줄여가며 최소자승법을 통하여 내부 소음원의 위치를 추정하였다. 알고리즘을 통해 계산한 값과 이론값을 비교하여 효용성을 입증하였으며, 수치시험을 통해 고정된 두 개의 외부 수중청음기와 음원 역할을 하는 수중체에 고정시킨 한 개의 신호발생기로 도플러 효과를 기반으로한 소음원의 3차원 위치 추정이 가능함을 증명하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.662-663
• /
• 2014

In most vehicle manufactures have traditionally relied on find-fix method of human auditor, mainly due to variation excitation source. To solve the BSR noise, the requirements for BSR test are presented in terms of detection of noise source, analysis of time-frequency and sound pressure, sound quality for noise. A number of new technology direction, particularly in the field of noise source identification application and psycho-acoustics from the Zwicker's sound quality parameter, the computed objective sound metrics and subjective jury test result.

• 한국소음진동공학회논문집
• /
• 제20권7호
• /
• pp.644-650
• /
• 2010

Among various elements to affect customer's evaluation of vehicle quality, BSR(Buzz, Squeak, Rattle) are considered to be a mostly contributing factor. In this paper, we provide the test method which can be used to reduce the BSR noise of instrument panel in a vehicle. First, potential source regions of the instrument panel for BSR are localized by using the vibration-excitor and near-acoustic field visualization system. Then, subjective evaluation of BSR noise from the detected potential noise source regions is made with the Zwicker's loudness and time-varying loudness methods. This illustrative analysis reveals that current experimental methods can be used as a test procedure to systematically tackle BSR issues in early stage of the vehicle development cycle, which can result in the reduction of the production cost.