• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.131-133
• /
• 2008

In this paper, the control method of extracting maximum power from the seaflow energy is proposed. This Paper describes a variable speed seaflow generation system with Permanent magnet synchronous motor, bridge rectifier, buck-boost converter and Fuzzy controller. In this Proposed seaflow generation system, the duty ratio of buck-boost converter is controlled by the fuzzy controller. An advantage of MPPT control method presented in this paper don't need to use the characteristic of seaflow turbine at various seaflow speed and measure the tidal speed and the rotating speed of tidal turbine. Therefore, the Proposed system has the characteristics of lower cost, higher efficiency and lower complexity. The effectiveness of algorithm is simulated based on Matlab Simulink.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.40-44
• /
• 1998

This paper describes variable speed drive and power control of a doubly fed induction machine(DFIM) for wind energy generation without rotational transducers. A stator flux orientation scheme and rotor speed estimator are employed to achieve decouple control of active and reactive power. To verify the theoretical analysis, a 5-hp DFIM prototype system and PWM power converter are built. Results of computer simulation are presented to support the discussion.

• Journal of Power Electronics
• /
• 제5권4호
• /
• pp.289-304
• /
• 2005

This paper describes a simple control structure and power conditioning system for an indirect vector controlled stand-alone induction generator (IG) used to operate under variable speed. The required reactive power for the IG system is supplied by means of a capacitor bank and a voltage-source PWM converter. Using a capacitor bank to transfer the reactive power to the IG under the rated speed and no-load conditions starts the IG operation and reduces the PWM converter size. The vector control structure for the variable speed IG power conditioning system compensates for changes in the electrical three-phase and DC loads while considering the magnetizing curve of the IG. The vector control structure is developed to regulate the DC link voltage of the PWM converter and the IG output voltage. The experimental and simulated performance results of the IG power conditioning system at various speeds and loads are given and show that this proposed scheme can be used efficiently for a variable speed, wind energy conversion system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.984-985
• /
• 2008

In this paper, MPPT(maximum power point tracking) control method of the seaflow generation system using DC-DC converters is proposed. This system consists of a variable speed seaflow generation system with permanent magnet synchronous generator, diode rectifier and DC-DC converter. In this proposed seaflow generation system, diode rectifier and DC-DC converter use for converting AC to DC and maximum power generation control, respectively. Advantages of MPPT control method presented in this paper don’t need to use the characteristic of the seaflow turbine at various seaflow speed and measure the seaflow speed and the rotating speed of seaflow turbine. Therefore, the proposed system has the characteristics of lower cost, lower complexity and higher efficiency. The effectiveness of algorithm is simulated and confirmed through Matlab Simulink.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2556-2558
• /
• 1999

We present voltage-source inverter for variable speed of washing machine. In the case of previous washing machines only on/off contol of motor was satisfied but these days the desire of customers moves to more silent and energy saving machine. Therefore many white goods manufacturers consider variable driving methods of motor. Nowadays variable speed Induction motors powered by inverters are becoming more and more popular. In this paper the principles of constant V/F control of Induction motor used in washing machine and space vector PWM technique are reviewd. Implementation issues such as command voltage generation, switching pattern determination, speed and power measurement are also presented. Experimental results are included in the end of the paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.208-210
• /
• 2007

As a renewable power source, wind power generation has been research interest for many years. And power electronic converters have been developed and applied in variable speed wind turbines. This paper presents the basic development and implementation of space-vector modulated three phase AC-AC matrix converter for variable speed wind power system. Basic matrix converter operation is described, where a new bidirectional switch structure with commutation circuit is used. Finally, experiment results of basic converter operation are shown.

• 전기학회논문지
• /
• 제58권7호
• /
• pp.1313-1320
• /
• 2009

This paper analyzes the steady-state operating characteristics of doubly-fed induction generator(DFIG) and fixed-speed induction generator(FSIG) in wind turbine system. It also presents a modeling and simulation of a grid-connected wind turbine generation system for dynamics analysis on MATLAB/Simulink, and compares the responses between DFIG and FSIG wind turbine systems with respect to wind speed variation, 3-phase fault and 1-phase ground fault of the network. Simulation results show the variations of generator's active/reactive output, rotor speed, terminal voltage, fault current, etc. Case studies demonstrate that DFIG illustrates better performance compared to FSIG.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.494_495
• /
• 2009

This paper presents a study of DFIG wind power generation system for real-time simulation. For real-time simulation, the real-time digital simulator (RTDS) and its user friendly interface simulation software (RSCAD) are used. 2.2MW grid-connected variable speed DFIG wind power generation system is modeled and analyzed in this study. Stator-flux oriented vector control scheme is applied to stator, rotor side converter control, and back-to-back PWM converters are implemented for the decoupled control. The real-wind speed signal extracted by an anemometer is used for realistic and accurate simulation analysis. Block diagrams for DFIG and control scheme of stator, rotor-side are introduced. Real-time simulation cases are carried out and analyzed for the validity of this work.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1068-1069
• /
• 2015

Wind turbines have an enormous potential for decentralized electricity generation. In recent years, there has been an increasing worldwide interest in small/medium wind systems. This paper presents the results of power performance testing conducted on a 50 kW turbine located in Yeonggwang test-bed. The turbine system is a pitch, active yaw, variable speed, upwind, three blade with a direct drive PMSG. This thesis covers the operation of variable speed wind turbines with pitch-yaw control. The system considered is controlled to generate maximum energy while minimizing loads. The data include power, wind speed, and direction from meteorological towers, and nacelle anemometer readings and output from turbine. The analysis concentrates on the effect of the load on the power-wind speed curve of the turbine.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1862-1867
• /
• 2011

Recently, a railway vehicle of the maximum speed of 350km/h or more high speed has been developed in the developed country. The next-generation railway vehicle(HEMU-400X) is being developed for aim to run over 430km/h in Republic of Korea, too. The safety of the railway vehicle should be conformed before manufacturing the railway vehicle. In this study, the next generation high-speed railway vehicle was modeled as a single-car system using commercial dynamic program ADAMS/Rail. Safety analysis was implemented through the international standard of the UIC 518 OR code. Also, appropriateness of the railway vehicle design variable were conformed by safety analysis results.