• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.3
• /
• pp.381-388
• /
• 2003

An experimental study was carried out to measure the heat transfer coefficient in flow boiling to mixtures of HFC-l34a and HCFC-123 in a uniformly heated horizontal tube. Tests were run at a pressure of 0.6 MPa and in the ranges of heat flux 1-50 kw/$m^2$, vapor quality 0-100 % and mass velocity 150-600 kg/$m^2$s. Heat transfer coefficients of mixture were less than the interpolated values between pure fluids both in the low quality region where the nucleate boiling is dominant and in the high quality region where the convective evaporation is dominant. Measured data of heat transfer are compared to a few available correlations proposed for mixtures. The correlation of Jung et. al. satisfactorily predicted the present data, but the data in lower quality was overpredicted and underpredicted the high quality data. The correlation of Kandlikar considerably underpredicted most of the data. and showed the mean deviation of 35.1%.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.3
• /
• pp.405-412
• /
• 2017

In the present study, two phase flows around a projectile vertically launched from an underwater platform have been numerically investigated by using a three dimensional multi-phase RANS flow solver based on pseudo-compressibility and a homogeneous mixture model on unstructured meshes. The relative motion between the platform and projectile was described by six degrees of freedom(6DOF) equations of motion with Euler angles and a chimera technique. The propulsive power of the projectile was modeled as the fluid force acting on the lower surface of the body by the compressed air emitted from the platform. Qualitative analysis was conducted for the time history of vapor volume fraction distributions. Uncorking pressure around the projectile and platform was analyzed to predict impact force acting on the surfaces. The results of 6DOF analysis presented similar tendency with the surficial pressure distributions.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.90-96
• /
• 2003

Numerical analyses have been performed to obtain the absorption heat and mass transfer coefficients and the absorption mass flux from a falling film of LiBr solution. In the present study, the behavior of laminar-wavy falling film in the vertical absorber was studied analytically and experimentally. The change of absorption performance on mean film thickness, wave amplitude, wave celerity was analysed. The heat and mass transfer equations are solved simultaneously to give the temperature and concentration variations at the LiBr solution/refrigeration vapor interface and at the wall. Effects of uniform film, wavy film and film Reynolds number on the heat and mass transfer coefficients have been estimated. The analytical results of the uniform and wavy falling film in the bare tube was higher than experimental result for $Rd_{t}<100$. The absorption performance showed the maximum at the wavy film by the insert device(spring).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.369.2-369.2
• /
• 2014

Diamond-like Carbon(DLC) films doping Si were deposited by linear ion source(LIS)-physical vapor deposition method on Si wafer. We have studied the effects of Si content on friction and wear properties of DLC films and the characteristics of the films were investigated using Nano-indentation, Micro raman spectroscopy, Field Emission-Scanning Electron Microscope (FM-SEM) and X-ray Photoelectron Spectroscopy (XPS). The films has been various low-friction and low-stress by varying the flow rates of silane gas. Under the about 2% of Si doping is very suitable for improving the adhesion of films and reducing internal stress while maintaining the surfaces hardness of DLC films. Linear ion source (LIS)를 사용하여 Si wafer위에 Si 이온이 첨가된 DLC 박막을 증착하였다. 참가된Si 이온의 양에 따라 DLC 박막에 미치는 영향을 분석하기 위하여 마찰 계수 및 경도를 비교하였고, Micro raman spectroscopy, Field Emission-Scanning Electron Microscope (FM-SEM) and X-ray Photoelectron Spectroscopy (XPS)를 통하여 표면 상태를 분석하였다. 천체 주입된 가스량의 약 2%까지 Si 이온 주입이 늘어날수록 DLC 박막의 마찰계수는 낮아졌고, 경도는 Si 이온이 주입되지 않았을 경우와 비슷한 값(약 20~23 GPa)을 가졌다. 2% 이상의 주입량에서는 마찰계수는 주입량이 늘어날수록 높아졌으며 경도는 떨어지는 경향을 보였다. 이는 Si이온이 2%이하로 첨가되었을 경우, DLC 박막의 생성시 탄소 이온들의 결합 Stress를 줄여 마찰계수가 줄어든다고 볼 수 있으며, 그 양이 2%이상이 되면 오히려 불순물로 작용하여 DLC 박막의 Stress는 급격히 증가하고 마찰계수도 높아짐을 알 수 있다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.658-661
• /
• 2002

Chemical species during growth of carbon nanotubes (CNTs) in direct current-plasma enhanced chemical vapor deposition were studied in details using $C_3H_4-NH_3$ and $CO-NH_3$ mixtures through optical emission spectroscopy (OES). In the $C_3H_4-NH_3$ system, the relative intensities of CN (388.3 nm) and CH (431.4 nm) decreased and that of $C_2$ (436 nm) increased, leading to $sp^2$-graphization into the CNT structure, leading to improvement of field emission property of CNTs. In the $CO-NH_3$ system, the trend is completely reversed. Attributing to the atomic oxygen for helping the graphitization of carbon, CNTs could be grown under the flow rate of CO (180 sccm)-$NH_3$ (10 sccm). Through these results, we suggest the growth mechanism in our system.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.327-331
• /
• 2009

A thermally coupled distillation system is constructed using two columns used in a conventional two column system, and its operability is examined by investigating the dynamic behavior. For the control of three product specifications, the step response test is performed and a $3{\times}3$ control structure using flow rates of overhead and side products and vapor boilup is suggested. The performance of the proposed control system indicates that the specification control of bottom product is the most difficult but the operation of the proposed system is available.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.6-13
• /
• 1987

A mathematical model for the waste heat recovery system for an engine was developed. The model based on the experimental data reported before was validated and was used to predict the waste heat recovery and recoverable heat of the engine at various operating conditions of the engine and the system. The model was also used to determine flow rates of the circulating water in the system for a certain temperature increment of the water at various operating conditions of the engine to give basic data to design the system. Stability of the system performance was tested on subjects of vapor lock problem, thermal characteristics of the thermostatic valve, and temperature variation of the circulating water in the engine and fuel consumption of the engine during each mode of the system operation and its change into the other. The test showed that the system operation was stable enough. Temperature profile in the thermal energy storage (TES) was observed during storing thermal energy, and thermal stratification in the TES was well formed acceptable to be used in the system. Finally a scheme to automatize the system was suggested.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.3
• /
• pp.303-315
• /
• 1998

Numerical and experimental studies on a heat pipe with two heat sources have been performed to investigate the operating characteristics. Numerical analysis was performed based on the cylindrical two-dimensional incompressible laminar flow for the vapor space and the conjugate heat transfer for the entire heat pipe. Experimental study with a 0.45 m length copper-water heat pipe was also performed to validate the numerical modeling for the heat input range from 29 W to 47 W on each heater. As results, the temperature profiles at the outer wall for the single active heat source as well as the temperature profiles for the switching operation between two heat sources are suggested. Due to the axial conduction, it is found that the temperature drop between the evaporator and the condenser appears small when the heat source closer to the condenser is turned on. For the switching operation in the present study, the transient time is about 700s and the temperatures at the locations of both heat source are same in 130s after switching.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1175-1180
• /
• 2003

Transformer Coupled Plasma Chemical Vapor Deposited (TCP-CVD) silicon nitride (SiNx) is widely used as a gate dielectric material for thin film transistors (TFT). This paper reports the SiNx films, grown by TCP-CVD at the low temperature (30$0^{\circ}C$). Experimental investigations were carried out for the optimization o(SiNx film as a function of $N_2$/SiH$_4$ flow ratio varying ,3 to 50 keeping rf power of 200 W, This paper presents the dielectric studies of SiNx gate in terms of deposition rate, hydrogen content, etch rate and leakage current density characteristics lot the thin film transistor applications. And also, this work investigated means to decrease the leakage current of SiNx film by employing $N_2$ plasma treatment. The insulator layers were prepared by two step process; the $N_2$ plasma treatment and then PECVD SiNx deposition with SiH$_4$, $N_2$gases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.309-312
• /
• 2007

The cryogenic fluid is the propellant for the liquid rocket engine. The design of space launcher vehicle is guided by minimum size and weight criteria, so the turbo pump solicits high impeller speed. Such high speed results in a zone of pressure drop below vapor pressure causing caivtation around inducer blades. The cryogenic fluid has different characters from isothermal fluid like water. The cryogenic fluid has very sensible thermodynamic properties and the phase change undergoes evaporative cooling. So, the developed code has to be modified cavitation modeling and it is added the energy equation for temperature sensitivity.