• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.131-135
• /
• 2010

In the present study, the effects of the stagger angles on the aerodynamic performances in the vaned centrifugal compressor has been investigated by CFD methods. The diffuser vane angles were vane angles were varied in the range of ${\pm}10$ deg. from the intial-design points. The commercial Navier-Stokes solver, ANSYS-CFX were applied to solve the impeller-diffuser flowfields. Through the numerical results, the desirable setting angles were proposed to fit the best performance to the variation of the operating conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.2 s.95
• /
• pp.129-134
• /
• 2005

This paper describes the influence of geometric parameters on the noise generation from a centrifugal compressor. From the analysis of noise measurements, it is observed that Blade Passing Frequency noise related to the rotating impeller is more important, and it is focused on the comparison of this discrete frequency noise according to the shape change. Navier-Stokes solver is used to simulate the flow-field of the impeller and the vaned diffuser, and time-dependent pressure data are calculated and Fourier-transformed to perform the near-field noise prediction. The effects of various geometry design variables such as the gap between the impeller and the diffuser, impeller shape variations on the near-field noise distribution are investigated.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2823-2828
• /
• 2007

Numerical simulation on the two-stage centrifugal compressor with Low Solidity Vaned Diffuser LSVD) for HFC-134a Turbo-chiller was performed using a commercial code. The comparative study with experimental results from other compressor was also investigated to testify the simulation schemes. The numerical analysis was separately simulated for each stage of the compressor and the effect of impeller-diffuser flow interaction was considered. Setting angle of the diffuser vane changed in the range of 15 deg. and the effects on its variation were discussed in detail including the flow analysis in the passage of the compressor. The vane setting angle obtained from the preliminary design was slightly adjusted to the optimal value by the performance enhancement in terms of pressure recovery and flow characteristics.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.422-427
• /
• 2000

The design of low-solidity vaned diffusers and the effect on the performance of a turbocharger compressor is discussed. The effect of vane number and turning angle was investigated while maintaining a basic design with a leading edge angle of $70^{\circ}$, leading and trailing edge radius ratios of 1.1 and 1.3. All results are compared with those obtained with the standard vaneless diffuser configuration and it was shown that all designs increased and shifted the pressure ratio to reduced flowrates. Despite the low-solidity configuration none of the vane designs provided a broad operating range, and the vane leading edge angle was not main factor that system went into the surge condition. The diffuser of higher trailing edge angle improved the flow range for the compressor to operate at lower flow region.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.2 s.7
• /
• pp.57-65
• /
• 2000

The aim of this paper is to understand the unsteady flow phenomena in a high speed centrifugal compressor channel diffuser. Instantaneous pressures aye measured at six locations in the diffuser using fast-response pressure transducers. Instantaneous pressure ratio decomposition was applied to analyze the pressure signal. In vaneless space where impeller-vaned diffuser interaction is strong, aperiodic unsteadiness is high and periodic pressure waveforms by blade passing are not clear at low flow rates, especially near vane suction side. High aperiodic unsteadiness decreases downstream of diffuser. The blade-to-blade pressure wave does not disappear in surge flow condition. In surge there exist not only large scale periodic surge wave but also blade-to-blade pressure wave.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.69-77
• /
• 1999

The aim of this paper is to understand the unsteady flow phenomena in a high speed centrifugal compressor channel diffuser. Instantaneous pressures are measured at six locations in the diffuser using fast-response pressure transducers. Instantaneous pressure ratio decomposition was applied to analyze the pressure signal. In vaneless space where impeller-vaned diffuser interaction is strong, aperiodic unsteadiness is high and periodic pressure waveforms by blade passing are not clear at low flow rates, especially near vane suction side. High aperiodic unsteadiness decreases downstream of diffuser. The blade-to-blade pressure wave does not disappear in surge flow condition. In surge there exist not only large scale periodic surge wave but also blade-to-blade pressure wave.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.3 s.12
• /
• pp.21-28
• /
• 2001

The effects of diffuser shapes on the flowfields of a small-size turbo-compressor have been investigated numerically and experimentally. The optimal design of elements shapes is important to develop the high efficiency turbo-compressor. Typical range of rotating speed for a small-size turbo-compressor is 40,000-70,000rpm. Numerical analyses were conducted to the rectangular and conical shapes of diffuser Three-dimensional, steady and viscous governing equations were solved by SIMPLE algorithm. To confirm the numerical results, the experimental measurements for the static pressure and temperature at the inlet and outlet boundaries were performed. Comparisons of these results were done, and the reasonable agreements were acquired.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.216-220
• /
• 2001

Flow analysis was carried out for two vertical pumps. The geometrical difference of two pumps is the adoption of vaned diffuser. Full pump models were used to simulate the velocity fields of the pumps. Pump head and velocity field were compared to obtain the features of diffuser flow. It was shown that the discontinuity of head curve was predicted and reverse flow could be generated at impeller exit even in the rated flow condition.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.187-192
• /
• 2000

The effects of diffuser shapes on the flowfields of a small-size turbo-compressor have been investigated by numerically and experimentally. It is important to optimal design of each elements for developing the small-size turbo-compressor Typical range of rotating speed of a small-size turbo-compressor is 40,000-70,000rpm. Numerical analyses are conducted to the rectangular and conical shapes of diffusers. Three-dimensional, steady, viscous governing equations are solved by SIMPLE algorithm. To prove the numerical results, experimental studies for the measurements of static pressure and temperature at the inlet and outlet boundaries are performed. Comparisons of these results are executed, and reasonable agreements are acquired.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.92-99
• /
• 2007

In this paper, optimization of the vaned centrifugal compressor was carried out at a given mass flow rate condition. Firstly, impeller optimization was conducted using response surface method (RSM) which is one of optimization methods. After the optimization of the impeller was completed, diffuser optimization was performed with the optimized impeller. In these processes, Navier-Stokes solver was used to calculate the flow inside the centrifugal compressor. And the optimization is performed with Box-Behnken design method which is efficient for fitting second-order response surfaces to reduce the number of calculations required. As a result, compared with the reference model, the efficiency and the pressure ratio of the optimized impeller and diffuser are found to be increased. The performance at off-design conditions is presented.