• 오토저널
• /
• 제16권4호
• /
• pp.1-5
• /
• 1994

1) Natural gas engine에서 intake valve와 valve seat insert가 exhuast valve와 valve seat insert보다 마모가 심하다. 2) Ceramic valve seat insert을 금속재료를 사용하는 것이 보다 더욱 효과적이다. 즉 적어도 3배 정도 마모가 적게 일어난다. 3) Ceramic valve와 ceramic valve seat insert로 결합한 경우 valve face 또는 stem 부위에서 응력이 집중되어 파손된다. 따라서 현재의 ceramic valve design methodology로는 ceramic valve은 좋은 결과를 얻을 수 없다. 4) 가장 효과적인 결합은 Tribolloy 800의 hardfacing 합금의 valve와 질화규소의 valve seat insert이다.

• 오토저널
• /
• 제15권4호
• /
• pp.1-7
• /
• 1993

최근 엔진의 고성능, 고출력화, 저연비화 Maintenance Free화에 따라 엔진의 부하가 증대되었고, Valve Seat에 대해서도 내마모성, 내열성, 내식성 향상이 요구되고 있다. 특히 무연가솔린과 LPG사용으로 내구성을 갖는 High Performance의 Valve Seat 재질을 요구하게 되었고, 엔진의 높은 작동온도등 가혹한 조건하에서 'Recession'이라 일컬어지는 Seat마모가 생기게 된다. Valve Seat는 일반적으로 분말야금법에 따라 제조되고 있으며, 엔진조건에 따라 여러가지의 재질이 사용되며, 높은 온도에서 열전도성과 기공의 산화방지 및 Valve 내구성 향상의 효과를 얻기 위하여 동용침을 하여 사용하는 추세이다. 본 실험에서는 Valve Seat 기공부위의 산화와 마모특성을 조사하기로 한다.

• 소성∙가공
• /
• 제18권8호
• /
• pp.607-616
• /
• 2009

There are three sub-processes associated with the assembly of the valve seat and cylinder head; heat fitting, cold fitting, and shrink fitting. In the heat fitting stage, the cylinder head is heated to a specified temperature and then squeezed toward the outer diameter of the valve seat. The cold fitting process cools the valve seat and safely squeezes it toward the inner diameter of cylinder head. However, these methods increased the installations & running cost and curtailed productivity. To address these problems, we analyzed the shrink fitting process using the contact pressure caused by fitting interference between the outer diameter of the valve seat and the inner diameter of the cylinder head. In this study, a closed form equation for predicting the contact pressure and fitting load is proposed. For quality control of the assembly line, principal factors of the shrink fitting process influenced in contact pressure were simulated by the FEM. Actual loads measured in the field showed good agreement with the results obtained by theoretical and finite element analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.129-132
• /
• 2004

This paper describes the design, fabrication and characteristics of a piezoelectric valve using MCA(Multilayer ceramic actuator). The MCA valve, which has the buckling effect, consists of three separate structures; MCA, a valve actuator die and an a seat die. The design of the actuator die was done by FEM modeling and displacement measurement, respectively. The valve seat die with 6 trenches was made, and the actuator die, which is driven to MCA under optimized conditions, was also fabricated. After Si-wafer direct bonding between the seat die and the actuator die, MCA was also anodic bonded to the seat/actuator die structure. PDMS sealing pad was fabricated to minimize a leak-rate. It was also bonded to seat die and SUS package. The MCA valve shows a flow rate of 9.13 sccm at a supplied voltage of 100 V with a 50 % duty cycle, maximum non-linearity was 2.24 % FS and leak rate was $3.03{\times}10^{-8}\;pa{\cdot}m^3/cm^2$. Therefore, the fabricated MCA valve is suitable for a variety of flow control equipment, a medical bio-system, automobile and air transportation industry.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.103-104
• /
• 2006

Wear of valve seating face and seat insert seating face influence the performance of engine, so they are important. To manufacture good quality valve and seat insert which have wear resistance the relations between wear factors and wear of the two seating faces have to be inspected. Cycle number is one of the important wear factors wearing the two seating faces and it can translate into mileage in rear car. But little is blown. Test variable is only cycle number and the cycle numbers are $2.0{\times}10^6,\;4.0{\times}10^6\;6.0{\times}10^6,\;8.0{\times}10^6$. And the other test conditions were fixed. Rmax of valve seating face and seat insert seating face increase linearly as cycle number is increased. Rmax of valve seating face were smaller than seat insert seating face in each cycle number. Reaction production by tribological reaction and sliding wear was found on the two faces.

• 센서학회지
• /
• 제13권3호
• /
• pp.230-235
• /
• 2004

This paper describes the design, fabrication and characteristics of a piezoelectric valve using MCA(Multilayer ceramic actuator). The MCA valve, which has the buckling effect, consists of three separate structures; MCA, a valve actuator die and an a seat die. The design of the actuator die was done by FEM modeling and displacement measurement, respectively. The valve seat die with 6 trenches was made, and the actuator die, which is driven to MCA under optimized conditions, was also fabricated. After Si-wafer direct bonding between the seat die and the actuator die, MCA was also anodic bonded to the seat/actuator die structure. PDMS sealing pad was fabricated to minimize a leak-rate. It was also bonded to seat die and SUS package. The MCA valve shows a flow rate of 9.13 seem at a supplied voltage of 100 V with a 50% duty cycle, maximum non-linearity was 2.24% FS and leak rate was $3.03{\times}10^{-8}pa{\codt}m^{3}/cm^{2}$. Therefore, the fabricated MCA valve is suitable for a variety of flow control equipment, a medical bio-system, automobile and air transportation industry.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.729-732
• /
• 2002

In this paper, poppet valve with cone type poppet and sharp edged seat was studied. In order to develope poppet valve which have a specification of 315(bar) and 3(lpm), effect of design parameter as valve seat diameter, poppet angle, spring stiffness and spring pre-load was evaluated. The validity of simulation was confirmed and basic data far poppet valve design was derived.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.17-22
• /
• 2018

A glove valve regulates the flow in a pipeline as a kind of control valve. However, when the disc and seat contact, the valve structure can be distorted and flow can leak due to the elongation of the valve material under high pressure. The surface texture is not good enough to seal the contact surface (in practice) because the lapping process is usually done manually. Furthermore, assembly performance is analyzed by structural analysis. Compared with a standard seat, the newly designed seat had a smaller radial deformation and a larger longitudinal deformation. Therefore, the newly designed seat can maintain a tight and uniform contact with the disc with a reduced radial deformation and an expanded available seal area with an increased longitudinal deformation. The seal performance of the glove valve has been improved in a cost-effective manner.

• Tribology and Lubricants
• /
• 제32권1호
• /
• pp.32-37
• /
• 2016

The wear characteristics of metal ball and seat in a metal-seated ball valve significantly affect the performances such as leakage and valve torque. In this work, the wear characteristics of metal ball and seat are experimentally investigated. A stainless steel ball and seat with a high corrosion-resistant coating are prepared and a component level test was performed. The hardness and surface roughness of specimens cut from the metal ball and seat are measured before and after the test using a micro-Vickers hardness tester and confocal microscopy, respectively. In order to assess the wear characteristics, the surfaces of the specimens are carefully examined after the test. The confocal microscope data show that the surface roughness values of both the ball and seat increase by a factor of 3-4, which may lead to an increase in valve torque. However, the wear of the seat is found to be more significant than that of the ball. In addition, a comparison of the surfaces of the ball and seat before and after testing revealed that adhesive and abrasive wear are the major wear mechanisms. The results of this study may aid in the design of metal-seated ball valves from the tribological point of view.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.75-80
• /
• 2014

In previous study, make an attempt to estimate exhaust valve seat and seat-ring wear acceleration factor for engine durability test with measuring and consideration of wear mechanism. But found abnormal initial wear rate in exhaust valve seat-ring. And have to improve exhaust valve seat-ring wear rate for reliability reason, because next GDI/Turbo engine is based on this engine and GDI/Turbo engine have higher combustion pressure and higher thermal load. In this study, Trying to find the cause of abnormal wear factor, improve valve-train durability by change specification & design of parts and verify variant parts for improving durability of valve-train. And then I would like to propose a design guide line of valve-train system in a reliability point of view, besides make a complement of previous study.