• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.76-82
• /
• 1999

The object of this study is to find new evalution index for in-cylinder flow characteristics insteady of current swirl, tumble coefficient using steady flow test rig on intake port system. To this end, port flow rig test was conducted on DOHC head varying intake valve lift respectively. Finally combination angular coefficient and inclination angle were introduced as new evaluation index for in-cylinder angular flow characteristics.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1998년도 제17회 KOSCI SYMPOSIUM 논문집
• /
• pp.103-110
• /
• 1998

This experiment is performed to investigate the effects of the emulsion on the flame temperature and soot formation in a diesel engine. The two-color method is used to measure the flame temperature for combustion of emulsified diesel in the Rapid Compression and Expansion Machine(RCEM). The concentration of soot is estimated via calculation of the KL factor. The solenoid valve, elecronic controller and needle lift sensor are used to control the exact injection timing and duration under various operating conditions. According to the results the soot concentration is reduced with the increasing W/O while the temperature reduced. The pressure data and the flame images captured by a high speed camera show that the ignition delay of emulsified diesel increase the duration of premixed combustion. The sizes of water drops are measured to be about 10${\mu}m$ by a microscope.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.156-165
• /
• 2014

This paper is the first investigation on the effect of flow control methods on the part load performance in a spark ignition engine. For comparison of the methods, two control devices, port throttling and masking, were applied to a conventional engine without any design change of the intake port. Steady flow evaluation shows that steady flow rates per unit opening area and swirl ratio are very low compared with the port throttling and saturated from mid-stage valve lift, however, swirl increases slightly as the lift is higher in case of 1/4 masking control. In the part load performance, the effect of simple port throttling on lean misfire limit expansion is limited and insufficient; on the other hand a masking improves the limit considerably without any port modification for increasing swirl. Also the results show that the intake flow control improves the combustion with following two mechanisms: stratification induced by the combination of the flow pattern and the fuel injection timing attribute to ignition ability and the intensified flow ensure fast burn. In addition fuel consumption reduces under the flow controls and the reduction rate is different according to the operation conditions and control methods. At the Stoichiometric and/or low speed and low load the throttling method is more advantageous; however vice versa at lean and high load condition. Finally, the throttling is more efficient for HC reduction than masking, on the other side the NOx emissions increase under the masking and decrease under the port throttling compared with conventional port scheme.

• 농업과학연구
• /
• 제43권3호
• /
• pp.450-458
• /
• 2016

High performance small and mid-sized tractors are required for dryland and orchard operations. A power transmission system is the most important issue for the design of high performance tractors. Many operations, such as loading and lifting, use hydraulic power. In the present study, a hydraulic power transmission system for the 3-point hitch of a 50 kW narrow tractor was developed and its performance was evaluated. First, major components were designed based on target design parameters. Target operations were spraying, weeding, and transportation. Main design parameters were determined through mathematical calculation and computer simulation. The capacity of the hydraulic cylinder was calculated taking the lifting force required for the weight of the implements into consideration. Then, a prototype was fabricated. Major components were the lifting valve, hydraulic cylinder, and 3-point hitch. Finally, performance was evaluated through laboratory tests. Tests were conducted using load weights, lift arm sensor, and lift arm height from the ground. Test results showed that the lifting force was in the range of 23.5 - 29.4 kN. This force was greater than lifting forces of competing foreign tractors by 3.9 - 4.9 kN. These results satisfied the design target value of 20.6 kN, determined by survey of advanced foreign products. The prototype will be commercialized after revision based on various field tests. Improvement of reliability should be also achieved.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제15권4호
• /
• pp.241-247
• /
• 2015

Purpose : The demand for higher fuel economy vehicles has helped develop fuel-efficient vehicles such as a CVVL called continuous variable valve lift. Existing CVVL has been applying DC type motor to control intake valve, but recently some car parts manufacturers have been developing a BLDC type CVVL motor for improvements of endurance performance. The purpose of this study is to find the potential failure mechanism of the CVVL BLDC moto in early stage of development based on the design properties and design the accelerated life test model. Methods : CVVL BLDC is consist of brushs, coil, magnetic, PCB, bearing and so on. Each component has a latent failure mechanism caused by temperature, humidity, vibration. By analysis result of the failure mechanism, thermal fatigue is the most important factor of a durability of CVVL BLDC motor. So, we designed a new accelerated life test model for guarantee of the CVVL BLDC motor. Results : A crack occurred on via hole in test using the conditions we designed, so we did change the design to avoid this failure. The via hole dimension is changed a little larger, as a result we achieve improvements in reliability of the CVVL BLDC motor. By applying various kinds and extreme level of stresses, we can find the operating limits of products. Conclusion : In thesis, We analyzed the failure mechanism of CVVL BLDC and designed an accelerated life test method to give a guarantee for reliability. Based on the test results, we could improve the reliability of developments by change of design.

• 한국항공우주학회지
• /
• 제44권12호
• /
• pp.1087-1094
• /
• 2016

발사체 지상고정장치는 지상운용시 발사패드에 기립된 발사체를 견고하게 지지하다가 발사시점에서 고정장치를 해제하여 발사체를 이륙하도록 하는 장치이다. 엔진점화이후 발사체 최대추력에서 발사체 고정의 급격한 해제는 Ka Doing a Doing a Doing 현상을 발생시켜 발사체 구조에 심각한 손상을 초래한다. 따라서, 발사체 지상고정장치는 고정력을 점진적으로 해제하기위한 기능이 요구된다. 또한 총 4개 고정장치의 해제 동작은 대단히 정밀하게 동시에 작동 하여야 한다. 본 연구에서는 복잡한 유압기기 없이 축압기 및 파이로 밸브에 의해 유압구동기의 속도를 발생시키고 오리피스로 속도를 제어함으로써 요구조건들을 충족하는 유압시스템을 제안하였다. 다물체 동역학 해석 및 Amesim을 이용한 유압시스템 해석을 통하여 유압구동기 목표속도를 도출하고 목표 속도를 만족하기 위한 오리피스의 단면적을 산출하였다. 이와 같은 연구를 통하여 복잡한 유압기기 없이 동작하는 신뢰도 높은 유압시스템을 설계하였다.

• 대한기계학회논문집B
• /
• 제40권7호
• /
• pp.417-427
• /
• 2016

본 논문은 반 쐐기형 연소실에서 포트 형상에 따른 정상유동 특성을 비교한 연구의 첫 번째로 통상적인 충격식 스월측정기 평가위치인 1.75B에서 입자영상유속계로 반 쐐기형 연소실에 직선형 포트와 나선형 포트를 적용하여 평면유속을 측정하고 비교하였다. 속도분포 분석 결과 직선형 포트에서는 밸브리프트 4 mm 이하, 그리고 나선형 포트에서는 2 mm 이하에서 두 개의 스월이 형성되고 이후 리프트가 증가하면 하나의 스월만 관찰된다. 리프트에 따른 유동체계의 천이점이 포트형상에 따라 상이하여 직선형 포트에서는 리프트 4 mm와 5mm를 경계로 유동 특성이 완전히 바뀌는 반면, 나선형 포트에서는 리프트 증가에 따라 점진적 변화만 관찰된다. 또한 모든 포트에서 1.75B 위치에서 편심도는 측정값이 왜곡되지 않는 범위에 들어오지 않고, 특히 직선형 포트의 편심도가 매우 크다. 동시에 포트형상에 관계없이 ISM 평가와 상응하는 실린더 중심 기준의 평균접선속도는 ISM 평가에서 가정한 속도보다 매우 낮고, 속도분포 특성도 ISM 평가의 가정과 매우 다르다.

• 대한기계학회논문집B
• /
• 제41권2호
• /
• pp.97-107
• /
• 2017

본 논문은 반 쐐기형 연소실에서 포트형상에 따른 정상유동 특성을 비교한 연구의 두 번째로 유동 평가위치의 영향을 고찰한 것이다. 입자영상유속계로 반 쐐기형 연소실에 직선형 포트와 나선형 포트를 적용하여 측정위치를 헤드 밑면부터 하류로 보어의 1,75배 위치 즉 1.75B부터 6배 위치 즉, 6.00B까지 변경하면서 평면유속을 측정하였다. 속도분포 분석 결과 반 쐐기형 연소실을 채택하면 지붕형과 달리 동일 리프트에서 거시적 유속분포와 유선은 스월 거동 중심은 측정위치가 관계없이 거의 일정하다. 직선형 포트에서는 모든 측정위치에서 편심도는 충격식 스월 측정기에서 측정값 왜곡이 발생하는 범위에 들어오고, 나선형 포트에서도 리프트 4mm 이하에서는 모든 측정위치에서 편심의 영향을 무시할 수 없지만, 측정위치가 3.00B 이상이 되면 리프트 5mm 이상에서 편심도가 급격히 감소한다. ISM가정과의 속도분포 차이에 의해 직선형 포트의 리프트 4mm 이하 스월 중심 평가를 제외하고 모든 PIV 평가방법에서 ISM 평가 대비 상대적인 상쇄효과가 있다. 마지막으로 중심 설정과 축 방향 속도분포 가정은 스월 평가에 정성적 영향을 주지 않고, 구체적인 접선속도 분포형태에 따라 절댓값에만 영향을 준다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.89-90
• /
• 2002

Ball reducer (HERB Drive: High Efficient Wave Rolling Ball Drive) with waved grooves has many advantages over other types of reducers for high-reduction ratio, low noise and low energy loss, etc. The mechanism of force transmission is very similar to that of cam and follower in automobile valve train system especially in contact behaviors. In this study, we have investigated the traces of contact between ball and outer ring, and the dynamic contact behaviors of elastohydodynamic lubrication(EHL) with a certain reduction ratio. In order to verify the contact behaviors between ball and outer ring for the critical endurance lift, the contact velocity and load are computed for a cycle. During some intervals of a cycle, the contact velocity reverses its direction very suddenly. It is expected that changing the contact direction causes undesirable endurance performance because EHL film frequently col lapse at the moment of velocity reversal. From the computational investigation in this work, we hope to predict similar contact damages in other machinery due to this kind of contact behaviors, which is very typical in many contact phenomena.

• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.128-135
• /
• 2008

EGR(exhaust gas recirculation) is considered as a most effective method to reduce the NOx emissions. But high EGR tolerance is always pursued not only for its advantages of the pumping loss reduction and fuel economy benefit in Gasoline-Hybrid engine. However, the occurrence of excessive cyclic variation with high EGR normally prevents substantial fuel economy improvements from being achieved in practice. Therefore, the optimum EGR rate should be carefully determined in order to achieve low fuel consumption and low exhaust emission. In this study, 2 liters gasoline engine with E-EGR system was used to investigate the effects of EGR on fuel efficiency, combustion stability, engine performance and exhaust emissions. With optimal EGR rates, the fuel consumption was improved by 4%. This improvement was achieved while a reduction in NOx emissions of 75% was accomplished. Increase of EGR gas temperature causes the charge air temperature to affect the knock phenomenon and moreover, the EGR valve lift changes for the same control signal.