• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2763-2768
• /
• 2007

Recently, as the semiconductor production technology develops, there has been growing interest in the cooling system using micro fluid pump. Among the various types of micro fluid pump, the valve-less diffuser/nozzle has been extensively studied in recent years. However, the flat-walled diffuser/nozzle flow has not been clearly looked into due to its non-linear characteristics. In this paper, the flow characteristics of the flat-walled diffuser/nozzle have been analyzed using similitude model and simulations. Similitude models are designed so that the flow pattern is same as that of 1/10 scale flow by using high viscous fluid as working fluid. The results are compared to the simulations. It is shown that the flow characteristics of 2D simulation are different from 3D simulations at high Re region, and the measured pump efficiency is highly dependent on the pressure difference as well as the channel geometry. From these results, the desirable conditions for the efficient pump is discussed.

• 대한기계학회논문집B
• /
• 제30권7호
• /
• pp.707-714
• /
• 2006

A numerical analysis study has performed in terms of fluid dynamics to identify the wall thinning generated in the main feedwater isolation valve body of a nuclear power plant. To review the relations between flow characteristics and the wall thinning induced by flow accelerated corrosion (FAC), numerical analysis using FLUENT code and ultrasonic tests (UT) were performed. The local velocities according to the analysis results were compared with the distribution of the measured wall thickness by ultrasonic tests. The comparison results show that the local velocity in the x-direction had no correlation with the wall thinning but the local velocity in the y-direction and turbulence intensity had a great influence on that. These results provide a good match to those of the previous studies - locations colliding vertically against components undergo severe wall thinning. These results may be utilized to the design modification and the wall thinning management for main feedwater isolation valves for preventing the wall thinning degradation.

• 센서학회지
• /
• 제16권1호
• /
• pp.44-51
• /
• 2007

A hybridized simulator for generating blood pressure waveform is proposed to study the remedy and/or evaluation of the conventional sphygmomanometer utilizing the oscillometric method which is widely applied. The blood pressure of a flowing fluid was controlled for the blood vessel's condition caused by a rhythmical and periodical contraction/relaxation because of the special excitatory and conductive system of the heart. In this study, a hybridized controller composed of the PI feedback controller and the feedforward controller. The inverse dynamics function is proposed to operating the control valve while the pressure is applied in an oil pressure tank. The proposed hybrid simulator reproducing the blood pressure waveform in an artificial blood vessel has kept the control performance consistent over all range. Based on these results, the proposed simulators could be applied to the development and compensation of the non invasive sphygmomanometer type as well as to study the characteristics of the blood pressure and blood vessel.

• Nuclear Engineering and Technology
• /
• 제26권1호
• /
• pp.32-40
• /
• 1994

중기발생기의 수위조절과 관련하여 최적제어이론을 이용한 디지탈 제어시스템을 설계하였다. 우선 급수변을 일차 지연함수로 취급하여 전체 시스템에 포함시킴으로써 보다 실제에 가까운 시스템이 되게 하였다. LQ 방법을 이용하여 급수변의 작동 및 요구신호량과 급수출력과의 차이를 최소화시킬 수 있는 최적 이득상수를 결정하였으며, 아울러 저출력에서의 급수유량 측정이 불확실함을 고려하여 급수신호에 대한 칼만 관측기를 설계하였다. 그리고 전출력 구간에서 일정한 안정여유도를 유지시킬 수 있는 가변상수 디지탈 제어기를 설계하였다. 이러한 제어시스템은 보다 현실적인 상황을 반영하고 있으며 저출력에서 급수와 반대현상을 보이는 중기발생기의 동특성에도 불구하고 만족할만한 제어특성을 보이고 있다.

• 대한의용생체공학회:의공학회지
• /
• 제13권4호
• /
• pp.285-298
• /
• 1992

An analysis of the dynamics in the closing phase of the occluder of a mechanical monoleaflet heart valve prosthesis is presented. The dynamic analysis of the fluid in the vicinity of the occluder was based on the control vo]use approach. The backflow velocity of the fluid was computed by applying the continuity, Bernoulli's and momentum equations in the unsteady state. By considering the fluid pressure and gravity as external forces acting on the occluder, the moment equilibrium on fine occluder was employed to analyze the motion of the occluder during closing and the force of impact between the occluder and the guiding struts. Occluder comes to rest after several oscillations in about 10-18 msec after the Inltiaton of closing. As the aortic pressure increases, the occludes closes faster and comes to the final resting position earlier and the impact force increases also. But backflow is not af footed by the variation of the aortic pressure. With decreasing time delay of the ventricle pressure, the occluder closes faster and impact force Increases. The computed magnitudes of the occluder tiP velocities as well as the backflow of the fluid during the closing phase using this model were in agreement with previously reported experimental measurements.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.806-811
• /
• 2001

Since the characteristics of combustion and pollutant in Diesel engines were mainly effected by the characteristics of in-cylinder gas flow and fuel spray, an understanding of those was essential to the design of the D.I. Diesel engines. The improvement of volumetric efficiency of air charging into combustion chamber is a primary requirement to obtain better mean effective pressure of an engine. Since parameters such as the air resistances in intake and exhaust flow passages, valve lift and valve shape influence greatly to the volumetric efficiency, it is very important to investigate the flow characteristics of intake and exhaust port which develops air motion in the combustion chamber. In this study, two approach methods were used for design intake and exhaust port; experiment and computation which were made by using steady flow test rig and commercial CFD code. This paper presents the results of an experimental and analytical investigation of steady flow through the prototype cylinder head ports and valves of the HHI's H21/32 HIMSEN Engine.

• 상하수도학회지
• /
• 제29권5호
• /
• pp.559-564
• /
• 2015

Distribution basins are used widely in the water treatment process. Uniform distribution at the distribution basin is an important because it affect precipitation efficiency of sedimentation basin. Generally distribution basin has a free surface water and is consisted of a weir. Study result, when inflow of distribution basin is less, amount of overflow is much at the nearest weir from the inlet. But when inflow is much, amount of overflow is much at the far weir from the inlet. The difference of distribution amount at the pipe is affected by the curvature and length of the pipe. The magnitude of the effect is determined by the relative energy loss and the flow state of the distribution basin. Optimization of the response surface method for minimizing an amount of deviation of the distribution is a very useful technique to determine the optimal ratio of the valve opening.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.74-79
• /
• 2009

The generation of electric power and plant facilities have been attempting to improve energy efficiency with many efforts as those being basis of our country's economy. In particular, the CHP(Combined Heat Power plant) system, is producing the electricity and process steam, has generally been using for the cogeneration plants. When CHP system operates, the steam has to maintain the high temperature and high pressure in order to have high efficiency of electric power production as much as possible. In addition, the exhausted steam from the turbine has to reform proper temperature to use the needed process. The major purpose of desuperheater is that the superheated steam changes into the saturated steam because it is more efficient and suitable for using the process, furthermore, it is more convenient and stable regarding the process temperature control. The design of the desuperheater obtained through the experiment and preceding analysis. This paper is verified by analysis that water spray nozzle(${\Phi}$=28mm) shows the best ability under the real power plant condition.

• 한국산업융합학회 논문집
• /
• 제25권1호
• /
• pp.87-99
• /
• 2022

We propoes a study on the dynamic characteristics analysis and position control of 5-degree multi-joint manipulators for untact remote working at construction sites and manufacturing plants. The main frame of freedom multi-joint manipulator consists of five elements, boom cylinder, boom cylinder, arm cylinder, bucket cylinder, and rotation joint and link. In addition, the main purpose of the proposed system is to realize the work of the manufacturing process or construction site by remote control. Motion control of the entire system is a servo valve control method by hydraulic servo cylinders for one to four joints, and a servo motor control method is applied for five joints. The reliability of the proposed method was verified through performance experiments by computer simulation.

• 한국항공우주학회지
• /
• 제34권3호
• /
• pp.74-80
• /
• 2006

본 논문은 선형 전기모터가 유압밸브 스풀(valve spool)을 직접 움직이는 직접구동밸브 (DDV: direct drive valve) 방식 유압서보 엑츄에이터의 제어 및 고장 모니터링에 관한 것이다. 유압서보 구동장치는 밸브 스풀을 통한 유량 흐름 특성으로 인하여 비선형 운동 특성을 갖게 된다. DDV 구동장치에 관한 비선형 운동 모델을 제시하고, 이를 선형화 시켜 DDV 구동장치의 제어계 및 고장 감지계 설계에 유용하게 사용될 수 있는 단순화된 선형 모델을 제시하였다. 한편, 조종면 구동 엑츄에이터가 만족시켜야 하는 성능 그리고 안전 작동에 관한 요구조건에 대하여 논의한 후, 이를 만족시키기 위한 제어계 및 고장 감지계의 구조에 대한 논의를 한다. 3중의 다중화 구조를 갖는 유압 DDV 구동장치의 운동 특성을 해석할 수 있는 수치해석 모델이 개발되었다.