• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.802-806
• /
• 2004

Skutterudite $CoSb_3$ powders were produced by mechanical alloying (MA) of elemental powders using a nominal stoichiometric composition. Annealing of MA powders under specific condition led to a complete phase transformation to a semiconducting ${\delta}-CoSb_3$. Single phase $CoSb_3$ was successfully produced by vacuum hot pressing using MA powders without subsequent annealing. Phase transformations during mechanical alloying and hot pressing were systematically investigated using XRD and SEM. Thermoelectric properties as a function of temperature were evaluated for the hot pressed specimens and compared with results of analogous studies.

• Applied Science and Convergence Technology
• /
• v.27 no.1
• /
• pp.19-22
• /
• 2018

The ion energy and angle distributions (IEADs) in the DC magnetron sputtering systems are investigated for the variation of gas pressure using particle-in-cell simulation. Even for the condition of collisionless ion sheath at low pressure, it is possible to change the IEAD significantly with the change of gas pressure. The bombarding ions to the target with low energy and large incident angle are observed at low pressure when the sheath voltage drop is low. It is because the electron transport is hindered by the magnetic field at low pressure because of few collisions per electron gyromotion while the ions are not magnetized. Therefore, the space charge effect is the most dominant factor for the determination of IEADs in low-pressure magnetron sputtering discharges.

• Tribology and Lubricants
• /
• v.20 no.2
• /
• pp.102-108
• /
• 2004

In this paper, friction and wear behaviors between monocrystalline, defect-free copper and carbon on the atomic scale are investigated by using 2-dimensional molecular dynamics simulation. It is assumed that all interatomic forces are given by Morse potential. The deformation of carbon is assumed to be neglected and vacuum condition is also assumed. Average friction and normal forces for various surface conditions, various scratch speeds and scratch depths are obtained from simulations. Changes of wear behaviors for various scratch speeds and surface conditions are investigated by observing snapshots in scratch process. The effects of surface conditions, scratch speeds, and scratch depths on the friction force, normal force, and friction coefficient are also investigated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.299-302
• /
• 2009

The objective of the present study is to analyze the transient flow through theejector system with the help of a computational fluid dynamics (CFD) method. An attempt is made to investigate the interesting and conflicting phenomenon of the infinite entrainment into the primary stream without an infinite mass supply from the secondary chamber. The results obtained show that the one and only condition in which an infinite mass entrainment can be possible in such types of ejectors is the generation of a re-circulation zone near the primary nozzle exit. The flow in the secondary chamber attains a state of dynamic equilibrium of pressures at the onset of the recirculation zone. A steady flow in the ejector system is valid only after this point.

• Transactions of Materials Processing
• /
• v.23 no.8
• /
• pp.507-512
• /
• 2014

The objective of the current investigation is to establish techniques in micro pattern forming operations of polymeric circular tubes by using hydrostatic pressing. This method was developed and successfully applied to the micro pattern forming on polymeric plates. The key idea of the new technique is to pressurize multiple vacuum-packed substrate-mold stacks above the glass transition temperature of the polymeric substrates. The new process is thought to be a promising micro-pattern fabrication technique for two reasons; first, (hydro-) isostatic pressing ensures a uniform micro-pattern replicating condition regardless of the substrate area and thickness. Second, multiple curved substrates can be patterned at the same time. With the prototype forming machine for the new process, micro prismatic array patterns, 25um in height and 90 degrees in apex angle, were successfully made on the PMMA circular tubes with diameters of 5~40mm. These results show that this process can be also used in the micro pattern forming process on curved plates such as circular tube.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.641-648
• /
• 2000

The horizontal drain method by installing drains horizontally in the ground is often used to expedite the dispersion of pore water and to increase the strength of dredged soft clay under the action of gravity or vacuum. In this study a numerical analysis method is developed to predict the consolidation process of soft ground with horizontal drains. One-dimensional self-weight consolidation theory is extended tn three-dimensions] theory with appropriate boundary conditions of horizontal drains. In the condition of pore water drainage by gravity, the behavior of the dredged clay with horizontal drains is compared with that of the clay without drains. The influence of design factors of drains on consolidation process is also analyzed.

• 전기의세계
• /
• v.20 no.2
• /
• pp.9-14
• /
• 1971

N type single crystal CdTe is grown by doping Gallium as 0.01 percent, by using zone melting method. And also p type CdTe is grown by doping Ag, Sb, and Te as 0.01%. Resistivity and Concentration of the n.p type single crystal are measured. And then Li ions are implanted on the n type CdTe by high voltage accellerator with different amount of impurity. Indium is evaporated on the p type in high vacuum condition. These sample are heated so as to make P-N Junction in Argon gas flow. Electrical properties for solar cell are investigated. Photovoltage and current are found to be varyed according to following factor: 1) amount of impurity 2) diffusion thickness 3) temperature and time for making P-N junction. Efficiency of the P-N Junction evaporated Indium is 6.5 when it is heated at 380.deg. C for 15 minutie.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1487-1489
• /
• 2001

The tantalum oxide($Ta_2O_5$) is an important material for present thin-film capacitor application owing to its high dielectric constant and thermal stability. We report dielectric property of Si(p type)/Pt/$Ta_2O_5$/Ag based MIM structure obtained by RF sputtering and annealed in vacuum environment. We have measured and researched the characteristics of C-F, C-V and EPMA. And we describe parameter dependence on sputtered condition and annealed temperature with dielectric property.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1890-1892
• /
• 2001

This paper described on the fabrication of microstructures by DRIE(Deep Reactive Ion Etching). SOI(Si-on-insulator) electric devices with buried cavities are fabricated by SDB technology and electrochemical etch-stop. The cavity was fabricated the upper handling wafer by Si anisotropic etch technique. SDB process was performed to seal the fabricated cavity under vacuum condition at -750 mm Hg. In the SDB process, captured air and moisture inside of the cavities were removed by making channels towards outside. After annealing(1000$^{\circ}C$, 60 min.), the SDB SOI structure was thinned by electrochemical etch-stop. Finally, it was fabricated microstructures by DRIE as well as a accurate thickness control and a good flatness.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1542-1547
• /
• 2003

This paper represents the solar collector performance with type of an evacuate double glass, and a copper tube was installed in center of collector to get a solar thermal energy. The one module of solar collector and artificial sun were used in this experiment The distance between artificial sun and solar collector was fixed at 0.5m, and this experimental condition was focused on winter season. The experiments were carried out. three times for getting a accurate data and the heat amount of one module evacuate d solar collector was estimated at out. 48 kcal/hr.