• Journal of electromagnetic engineering and science
• /
• v.13 no.1
• /
• pp.44-50
• /
• 2013

In this paper, we present a circularly polarized (CP) composite cavity-backed crossed dipole antenna for global positioning system (GPS) applications. We produce the CP radiation by crossing two dipoles through a $90^{\circ}$ phase delay line of a vacant-quarter printed ring, which also has a broadband impedance matching characteristic. Two techniques, insertion of meander lines in the dipole arm and arrowhead-shaped trace at its end, are employed to reduce the sizes of the primary radiation element. The compact radiator is backed by a cavity reflector to achieve a wide CP radiation beamwidth. The proposed antenna exhibits a measured bandwidth of 1.450~1.656 GHz for a voltage standing wave ratio (VSWR) < 2 and 1.555~1.605 GHz for AR < 3-dB. At 1.575 GHz, the antenna has a gain of 7 dBic, a frontto-back ratio of 27 dB, AR of 1.18 dB, and 3-dB AR beamwidths of $130^{\circ}$ and $132^{\circ}$ in the x-z and y-z planes, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1744-1751
• /
• 2006

In this paper shows the Designed and Manufactured active antenna for wireless LAN that is consisted of 5.5GHz band local LNA and Microstrip Patch Antenna. LNA improved noise special quality using NEC company's NE3210S01 and Micnstrip Patch Antenna designed to have omnidirectional characteristic. Designed $1{\times}2$ Microstrip Patch Antenna to have the gain of about 8.3[dBi], the input reflection loss -32[dB], VSWR showed 1.132, and the LNA gain 15[dB], input-output reflection loss was showed the characterstic of -20[dB].

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.339-346
• /
• 1999

A RF receiver section for INMARSAT-C external mounting unit was designed, fabricated and evaluated. Using a INA-03184, the high gain amplifier consists of matched amplifier type. Active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver section implemented here show 60 dB in gain, 44.83 dBc in a spurious level. The voltage standing wave ratios(VSWR)of input output port are less than 1.8:1, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.7
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1611-1618
• /
• 2017

This paper presents a compact reconfigurable printed monopole antenna, operating in three different frequency bands (2.45 GHz, 3 GHz and 5.2 GHz), depending upon the state of the lumped element switch. The proposed multiband reconfigurable antenna is designed and fabricated on a 1.6 mm thicker FR-4 substrate having a relative permittivity of 4.4. When the switch is turned ON, the antenna operates in a dual band frequency mode, i.e. WiFi at 2.45 GHz (2.06-3.14 GHz) and WLAN at 5.4 GHz (5.11-5.66 GHz). When the switch is turned OFF, it operates only at 3 GHz (2.44-3.66 GHz). The antenna radiates omni-directionally in these bands with an adequate, bandwidth (>10 %), efficiency (>90 %), gain (>1.2 dB), directivity (>1.7 dBi) and VSWR (<2). The fabricated antenna is tested in the laboratory to validate the simulated results. The antenna, due to its reasonably compact size ($39{\times}37mm^2$), can be used in portable devices such as laptops and iPads.

• Journal of Advanced Navigation Technology
• /
• v.13 no.5
• /
• pp.714-719
• /
• 2009

In this paper, a compact antenna with band-rejected characteristic for Ultra-Wideband(UWB) applications is proposed. The designed antenna not only shows sufficient impedance bandwidth but has band-rejected characteristic for the frequency band of 5.15~5.825GHz limited by IEEE 802.11a and HIPERLAN/2. To obtain both properties of wideband band rejection, the techniques of a partial ground plane and embedded thin U-slot into planar radiator are used respectively. A designed antenna satisfied a VSWR less than 2:1 for the frequency band of 3.1~10.3GHz with band rejection of 4.90~5.92GHz.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2011

In this paper, dual-feed circularly polarized microstrip patch antenna for GPS L1, GPS L2, GLONASS L1 signal was fabricated by using stacked patch. It was fed by dual coaxial probe on the patch at 50ohm impedance, and was simulated to resonate at GPS L1, GPS L2, GLONASS L1. To realize characteristics of right hand circular polarization using dual-feed stacked patch antenna and hybrid coupler for $90^{\circ}$ phase difference. Output of hybrid coupler was contacted input of Low Noise Amplifier(LNA). The LNA using dual band pass filter was designed and fabricated. The measured results of the implemented antenna is VSWR < 1.5 : 1 and the gain of 32dB(Zenith) over at GPS L1, L2, GLONASS L1.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6A
• /
• pp.833-838
• /
• 2000

In this paper, a novel type of wideband single-patch microstrip antenna using the reactive-loading technique is presented. We demonstrated that, by inserting stubs at both of the radiating edges, the frequencies of the two resonant modes are closely spaced to form a wide operating bandwidth. Segmentation technique and cavity model are used to analyze the antenna characteristics and experimental data are show to be in good agreement with the calculated results. With the proposed structure, the measured antenna bandwidth of 230MHz is obtained, which is almost 2.65 times larger than that of an unloaded rectangular patch antenna and fully covers the whole frequency range of 1.885GHz~2.025GHz allocated to IMT-2000.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.530-538
• /
• 1999

In this paper, design of rectangular iris waveguide filter for the microwave broadcasting transponder using WR137 is applied to the modified ${TE^x}_{mn}$ mode theory in order to exactly analyze the characteristic of the waveguide discontinuity. We designed and fabricated the rectangular iris waveguide filter with the bandwidth 47 MHz for the microwave broadcasting transponder applied the conjugate gradient method to the modified ${TE^x}_{mn}$ mode theory. The results show a good characteristics that the $S_{11}$ and $S_{21}$ are -23 ㏈, -0.56 ㏈ and the maximum VSWR is below 1.02 in the passband.

• Journal of electromagnetic engineering and science
• /
• v.15 no.3
• /
• pp.185-193
• /
• 2015

In this paper, a hybrid multiple input multiple output (MIMO) antenna for eight-band mobile handsets is designed and implemented. For the MIMO antenna, two hybrid antennas are laid symmetrically and connected by an interconnection tie, thereby enabling complementary operation. The tie affects both the impedance and radiation characteristics of each antenna. Further, printed circuit board (PCB) embedded type is applied to the antenna design. To verify the results of this study, we designed eight bands-LTE class 12, 13, and 14, CDMA, GSM900, DCS1800, PCS, and WCDMA-and implemented them on a bare board the same size as the real board of a handset. The voltage standing wave ratio (VSWR) is within 3:1 over the entire design band. Antenna isolation is less than -15 dB at the lower band, and -12 dB at the WCDMA band. Envelope correlation coefficient (ECC) of 0.0002-0.05 is obtained for all bands. The average gain and efficiency are measured to range from -4.69 dBi to -2.88 dBi and 33.99% to 51.5% for antenna 1, and -4.74 dBi to -2.97 dBi and 33.45% to 50.49% for antenna 2, respectively.