• Journal of Environmental Science International
• /
• v.22 no.7
• /
• pp.823-836
• /
• 2013

Emissions of air pollutants and greenhouse gases (GHGs) from aircraft activities at 11 small-scale airports were investigated using the emissions and dispersion modeling system (EDMS) version 5.1.3 during the two year period of 2009~2010. The number of landing and take-off (LTO) at these airports was dominant for the aircraft type B737, accounting for more than 60% of the total LTOs. Out of the 11 small-scale airports, Gwangju (GJ, RKJJ) airport was the largest emitter of air pollutants and GHGs, whereas Yangyang (YY, RKNY) airport was the smallest emitter. The emissions of $NO_x$ and VOCs in 2010 at the 11 airports ranged from 1.9 to 83 ton/y and 0.1 to 17 ton/y, respectively. In 2010, the emissions of $CO_2$ ranged from 394 to 21,217 ton/y. The emissions of most air pollutants (except for $NO_x$ and $PM_{10}$) and GHGs were estimated to be the highest in taxi-out mode. The highest emissions of $NO_x$ and $PM_{10}$ were emitted from climb-out and approach modes, respectively. In addition, the total LTOs at the 11 small-scale airports accounted for the range of 9.3~9.9% of those at four major international airports in Korea. The total emissions of air pollutants and GHGs at the 11 airports ranged from 4.8 to 12% of those at the four major airports.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.125-132
• /
• 2011

As the enhancement of indoor air quality is increasingly compelling the use of natural materials without any emission, this study reports the preparation and performance of natural garlic adhesives for wallpaper. The natural garlic adhesives were successfully prepared by the extraction of the clove of raw garlic with water to isolate carbohydrates and proteins. Properties of the prepared garlic adhesives such as the non volatile solids content, viscosity, density, and pH were 62%, 2,789 mPa.s, $1.3g/cm^3$, and 6.6, respectively. The non-volatile solids content has a great impact on the adhesion performance of the prepared garlic adhesives, which was adequate about 60%. Bonding strength of prepared garlic adhesives was greater than the requirement of a Korean standard for wallpaper. In addition, the garlic adhesives showed antibacterial activity inheriting from the garlic. It is expected that the prepared garlic adhesives could be used as safe and natural adhesives without emitting any volatile organic compounds and formaldehyde gas.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.236-236
• /
• 2017

Effluent treated by an NaDCC injection method in Ballast water management system (BWMS) contains reactive chlorine species and disinfection by-products (DBPs). In this study, we conducted whole effluent toxicity (WET) testing and ecological risk assessment (ERA) to investigate its ecotoxicological effects on marine environment. WET testing was carried out for four marine pelagic and freshwater organisms, i.e., diatom Skeletonema costatum, Navicula pellicuosa, chlorophyta Dunaliella tertiolecta, Pseudokirchneriella subcapitata, rotifer Brachionus plicatilis, Brachionus calyciflorus and fish Cyprinodon variegatus, Pimephales promelas. The biological toxicity test revealed that algae was the only biota that showed apparent toxicity to the effluent; it showed no observed effect concentration (NOEC), lowest observable effect concentration (LOEC) and effect concentration of 50% (EC50) values of 25-50%, 50-100% and >100%, respectively, at three water condition, but did not show any significant toxicities on other biota. Meanwhile, chemical analysis revealed that the BWMS effluent contained total residual oxidants (TROs) below $0.03{\mu}g/L$ and a total of 25 DBPs such as bromate, volatile halogenated organic compounds (VOCs), halogenated acetonitriles (HANs), halogenated acetic acids (HAAs), chloropicrin and Isocyanuric acid. Based on ERA, the 25 DBPs were not considered to have persistency, bioaccumulation and toxicity (PBT) properties. The ratio of predicted environmental concentration (PEC) to predicted no effect concentration (PNEC) of the other DBPs did not exceed 1 for General harbor environment. However, four substances (Isocyanuric acid, Tribromomethane, Chloropicrin and Monochloroacetic acid) were exceed 1 for Nearship environment. But observed toxicity in the test water on algal growth inhibition would be mitigated by normal dilution factor of 5 applied for nearship exposure. Thus, our results of WET testing and ERA showed that the BWMS effluent treated by NaDCC injection method would have no adverse impacts on marine environment.

• Korean Chemical Engineering Research
• /
• v.45 no.3
• /
• pp.277-285
• /
• 2007

The adsorption characteristics of multi-component solvent vapors including poorly-adsorbable chemicals such as toluene-xylene-MEK and toluene-MEK-IPA on the activated carbonaceous adsorbents were investigated in a stainless steel fixed bed of 10.2 cm ID and 50 cm in height in order to identify those carbons for eliminating and recovering solvent vapors from industrial emission sources. The used activated carbonaceous adsorbents were pelletized commercial activated carbons and activated carbon fiber. Breakthrough curves and adsorption capacity at atmospheric pressures were obtained. It has been found that non-polar and larger molecules have been adsorbed better than polar and smaller molecules. In special, alcohols and ketones were poorly adsorbed caused by competitive adsorbability in multi-component mixture system. However, it could be overcome by profitable employment of organization of cooperative system which was composed of different porosity activated carbonaceous adsorbents appropriately.

• Journal of Environmental Health Sciences
• /
• v.26 no.4
• /
• pp.141-147
• /
• 2000

Due to a rapid in automobiles since the 1980’s, the concentration of NO, and HC has also increased along with cases of VOCs. These air pollutants have created $O_3$ concentration, which cause a harmful effect to the human health. This issue has become a subject of great public interest. For this paper, to compare the concentration of $O_3$, NO, N $O_2$ between the rural and urban area in the winter, the concentrations of each have been measuredevery hour during Jan.~Feb. 2000, 1998, respectively. To calculate the Photochemical Steady State, $\Phi$= $J_{N O_2}$[N $O_2$]/ $k_1$[NO][ $O_3$], temperature and $J_{ N O_2}$ has been determined. The NO concentration in the rural are showed at below 10 ppb while the NO concentration in the urban area showed maximum value of 90~120 ppb. But the $O_3$ concentration in both areas showed less than 30 ppb. The reason is that the N $O_2$ photodissiciation rate is low due to the temperature being below 2$^{\circ}C$ and less than 60 degrees in the solar zenith angle during the winter time, which makes the $O_3$ concentration in both areas, similar in the concentration level. N $O_2$ photodissociation rate in both ares showed maximum value of 3.0mW/$\textrm{cm}^2$. Values of $\Phi$ determined from the rural area was consistently the unity, approaching 1. But values of $\Phi$ determined from the urban was roughly higher than unity, approaching above 1or 2 for clear sky-high sun(10:00~16:00).

• Journal of Korean Society for Atmospheric Environment
• /
• v.32 no.2
• /
• pp.131-157
• /
• 2016

A smog chamber has been an effective tool to study air quality, particularly secondary organic aerosol (SOA), which is typically formed by atmospheric oxidation of volatile organic compounds (VOCs). In controlled environments, smog chamber studies have validated atmospheric oxidation by identifying, quantifying and monitoring products with state-of-art instruments (e.g., aerosol mass spectrometer, scanning mobility particle sizer) and provided chemical insights of SOA formation by elucidating reaction mechanisms. This paper reviews types of smog chambers and the current state of smog chamber studies that have accomplished to find pathways of SOA formation, focusing on gas-particle partitioning of semivolatile products of VOC oxidation, heterogeneous reactions on aerosol surface, and aqueous chemistry in aerosol waters (e.g., cloud/fog droplets and wet aerosols). For future chamber studies, then, this paper discusses potential formation pathways of fine particles that East Asia countries (e.g., Korea and China) currently suffer from due to massive formation that gives rise to fatal health problems.

• Environmental Analysis Health and Toxicology
• /
• v.27
• /
• pp.12.1-12.8
• /
• 2012

Objectives: The aim of this study was to identify the health and environmental risk factors of air contaminants that influence environmental and respiratory diseases in Gyeongju, Pohang and Ulsan in South Korea, with a focus on volatile organic compounds (VOCs). Methods: Samples were collected by instantaneous negative pressure by opening the injection valve in the canister at a fixed height of 1 to 1.5 m. The sample that was condensed in $-150^{\circ}C$ was heated to $180^{\circ}C$ in sample pre-concentration trap using a 6-port switching valve and it was injected to a gas chromatography column. The injection quantity of samples was precisely controlled using an electronic flow controller equipped in the gas chromatography-mass spectrometer. Results: The quantity of the VOC emissions in the industrial area was 1.5 to 2 times higher than that in the non-industrial area. With regards to the aromatic hydrocarbons, toluene was detected at the highest level of 22.01 ppb in Ulsan, and chloroform was the halogenated hydrocarbons with the highest level of 10.19 ppb in Pohang. The emission of toluene was shown to be very important, as it accounted for more than 30% of the total aromatic hydrocarbon concentration. Conclusions: It was considered that benzene in terms of the cancer-causing grade standard, toluene in terms of the emission quantity, and chloroform and styrene in terms of their grades and emission quantities should be selected for priority measurement substances.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.467-470
• /
• 2010

USN(Ubiquitous Sensor Network) is the network that widely applies for life of human being. It works out to sense, storage, process, deliver every kind of appliances and environmental information from the stucktags and sensors. And it is possible to utilize to measure and monitor about the place of environmental pollution which is difficult for human to install. It's studied constantly since it be able to compose easily more subminiature, low-power, low-cost than previous one. And also it spotlights an important field of study, graft the green IT and IT of which the environment and IT unite stragically onto the Network. This study realize a IAQM(Indoor Air Quality Management) sensing mechanism composition under the network and suggest the application of Environment monitoring system outlook to measure an Environment element.

• Membrane Journal
• /
• v.15 no.1
• /
• pp.44-51
• /
• 2005

Polyurethane-polysiloxanes (PU/PDMS) was synthesized using 4,4'-diphenylmethane diisocyanate (MDI) and 1,4-butanediol (BD) to overcome the weakness to the organic chemicals. The composite membranes were prepared onto porous poly(tetrafluoroethylene) (PTFE) supports. In vapor permeation experiments, the flux increased with increasing operating temperatures and feed concentrations while the separation factors showed the opposite trend, so-called 'trade-off'. In this study, the effect of the flux on the operating temperatures was not severe since the content of the soft segments is fairly higher than that of the hard segments. The composite membrane type of PU/PDMS maintained high flux and separation factor as well when comparing with the dense type membranes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.72.1-72.1
• /
• 2013

광촉매 활용 기술은 수질 및 대기 중의 난분해성 오염 물질 처리 등의 환경 분야에서부터 항균 및 초친수성 기능을 활용한 소재 분야, 그리고 태양광을 이용한 물분해 수소 제조 및 이산화탄소의 전환 등의 인공 광합성 연구 분야까지 그 응용분야가 대단히 넓은 기술이다. 본 강연에서는 이러한 광촉매의 반응 원리와 대표적인 응용분야인 환경 정화 분야 및 에너지 분야에서의 광촉매 기술의 활용, 그리고 현재 광촉매 관련 연구 분야의 주요 관심사 및 미래 성장을 위한 과제 등을 포괄적으로 다루고자 한다. 광촉매 반응은 반도체의 따간격 에너지 흡수에 따라 전자와 정공(+전하를 가진 전자와 같은 거동을 하는 입자)가 발생한 뒤에 일어나는 계면에서의 전자전달 반응을 기초한다. 발생한 정공과 전자는 각각 산화와 환원 반응을 유발하며 이러한 산화, 환원반응을 통해 다양한 분야로의 응용이 가능하다. 환경 정화 분야의 경우, 정공이 물 혹은 공기 속에 존재하는 수분과 반응하여 생성되는 OH 라디칼 ($OH{\cdot}$)의 강력한 산화력을 주로 이용하게 된다. OH 라디칼에 의한 다양한 난분해성 유기물질의 산화분해 반응을 활용하여 고도처리공정이 가능하게 되며, 수계 난분해성 유기오염물질의 제거뿐만 아니라 대기 중에 존재하는 VOCs, 악취물질 등의 분해도 가능하며, 아울러 바이러스나 박테리아와 같은 세균을 제거할 수 있는 것으로 알려져 있다. 한편, 물 분해 수소제조 및 이산화탄소의 전환과 같은 에너지 분야 응용의 경우, 전도대의 전자를 활용한 환원반응에 기초한다. 앞서 언급한 다양한 응용분야에서 활용될 수 있는 광촉매의 종류 또한 매우 다양하며, 이사화티탄(TiO2)는 대표적인 고효율 상용 광촉매이다. 아울러, 원하는 응용 분야에서의 광활성이 높은 새로운 광촉매의 제조 및 평가가 꾸준히 진행되고 있으며, 그 가운데 태양광의 가장 많은 영역을 차지하고 있는 가시광 활성을 갖는 광촉매 개발에 관한 연구가 활발히 수행되고 있다. 이에, 현재까지 개발된 다양한 가시광 광촉매 시스템에 대한 소개 및 각 광촉매 응용분야에서 최근 새롭게 대두되고 있는 이슈들에 대하여 중점적으로 고찰하고자 한다.