• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.8
• /
• pp.432-437
• /
• 2004

Since the characteristic frequency is decreased in proportion to the fault distance, the characteristic frequency component may be insufficiently eliminated by a low-pass filter on a long transmission line. In order to set a standard for the cut-off frequency of the low-pass filter, this paper proposes a method for obtaining the characteristic frequencies due to line faults. The application results of the proposed method are presented for line to ground (LG) faults and line to line (LL) faults on a 345 kV 200 km overhead transmission line. The EMTP is used to generate fault signals under different fault locations and fault inception angles. By comparison between the characteristic frequencies obtained from the proposed method and the EMTP simulation, it is shown that the proposed method accurately obtains the characteristic frequency.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.3
• /
• pp.76-83
• /
• 2000

The continuous time signal system by development of CMOS technology have been receiving consideration attention. In this paper, Low pass filter using new CMOS floating resistor have been designed with cut off frequency for speech signal Processing. Especially a new floating resistor consisting entirely of CMOS devices in saturation has been developed. Linearity within $\pm$0.04% is achieved through nonlinearity via current mirrors over an applied range of $\pm$1V The frequency response exceeds 10MHz, and the resistors are expected to be useful in implementing integrated circuit active RC filters. The low pass filter designed using this method has simpler structure than switched capacitofilter. So reduce the chip area. The characteristics of the designed low pass filter using this method are simulated by pspice program.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2395-2402
• /
• 2013

An active-RC channel selection filter (CSF) with the bandwidth of 40MHz and the improved linearity is proposed in this paper. The proposed CSF is the fifth butterworth filter which consists of a first order low pass filter, two second order low pass filters of a biquad architecture, and DC feedback circuit for cancellation of DC offset. To improve the linearity of the CSF, a body node of a MOSFET for a switch is connected to its source node. The bandwidth of the designed CSF is selected to be 10MHz, 20MHz and 40MHz and its voltage gain is controlled by 6 dB from 0 dB to 24 dB. The proposed CSF is designed by using 40nm 1-poly 8-metal CMOS process with a 1.2V. When the designed CSF operates at the bandwidth of 40 MHz and voltage gain of 0 dB, the simulation results of OIP3, in-band ripple, and IRN are 31.33dBm, 1.046dB, and 39.81nV/sqrt(Hz), respectively. The power consumption and layout area are $450{\times}210{\mu}m^2$ and 6.71mW.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.433-440
• /
• 2021

The problem of maritime accidents due to the carelessness of fishing vessels, which is affected by the aging of fishing vessel operators. And there is navigation, communication and fish finder that is installed inside the narrow bridge of a fishing vessel. Therefore these system are monitors as many as of each terminal, which is bad influence on obscuring view of front sea from a fishing vessel bridge. In addition a large problem, it is occurs to reduce of the information recognition ability due to the confusion, which is can not check the display information each of screen equipments. Therefore, there has been demand to simply integrated the equipment, and it has wanted the integrated support system of these equipment. The display must be provided on a fishing vessels such as electronic charts, communications equipments and fish detection into one case. In this paper, the integrated system will be installed the GPS plotter, AIS, VHF-DSC, V-pass, fish finder and power supply in the narrow wheelhouse on a fishing vessel, which is configured in one case and operated by multi function display (MFD). The MFD is integrated to simplify for several multi terminals and provided necessary information on a single screen. This integration fishery support system will has improved in sea safety operation and fishery environment of fishing vessels by this implementation.

• Journal of Bio-Environment Control
• /
• v.15 no.1
• /
• pp.8-20
• /
• 2006

This research was conducted to determine the plant growth and nutrient contents of potted chrysanthemum 'Lima Honey' as influenced by application rate of dolomite in three root media, peatmoss+vermiculite (1:1, v/v), peatmoss+composted rice hall (1:1, v/v), and peatmoss+composted pine bark (1:1, v/v). All root media contained polyacrylic acid sodium salt (PASS) at a rate of $4.5g L^{-1}$. In crop growth at 40 and 80 days after transplanting, elevated application rates of dolomite up to $6.0g L^{-1}$ in three root media increased fresh and dry weights per plant. But the treatment of $9.0g L^{-1}$ had less fresh and dry weights than those of $6.0g L^{-1}$. Tissue phosphorus content decreased and those of Ca and Mg increased by the elevated application rates of dolomite. Elevated application rates of dolomite in three root media resulted in the increase of pH, EC, and the concentrations of K, Ca, and Mg at 43 days after transplanting. Those at 80 days after transplanting were also increased, but the differences among treatments were less significant as compared to those at 43 days after transplanting. From the results of dry weight in potted chrysanthemum 'Lima Honey', the proper application rate of dolomite to three root media containing PASS at a rate of $4.5g L^{-1}$ were $6.0g L^{-1}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.7
• /
• pp.1303-1310
• /
• 2016

In this paper, electrocardiogram (ECG) analog front end with supply voltage of 0.5V has been designed and verified by measurements of fabricated chip. ECG is composed of instrument amplifier, 6th order gm-C low pass filter and variable gain amplifier. The instrument amplifier is designed to have gain of 34.8dB and the 6th order gm-C low pass filter is designed to obtain the cutoff frequency of 400Hz. The operational transconductance amplifier of the low pass filter utilizes body-driven differential input stage for low voltage operation. The variable gain amplifier is designed to have gain of 6.1~26.4dB. The electrocardiogram analog front end are fabricated in TSMC $0.18{\mu}m$ CMOS process with chip size of $858{\mu}m{\times}580{\mu}m$. Measurements of the fabricated chip is done not to saturate the gain of ECG by changing the external resistor and measured gain of 28.7dB and cutoff frequency of 0.5 - 630Hz are obtained using the supply voltage of 0.5V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.136-136
• /
• 2009

It is investigated the cut-off frequency of Z-cut quartz microstrip low pass filter by the variation of applied electric field. Designed microstrip filter was simulated using the Ensemble v7.0(Ansoft). As a result of the experiment, the cut-off frequency showed 50 MHz shift when the applied electric field was 3 kV/cm.

• Bulletin of the Korean Mathematical Society
• /
• v.55 no.5
• /
• pp.1441-1462
• /
• 2018

In this paper, we investigate the fractional p&q-Kirchhoff type system $$\{M_1([u]^p_{s,p})(-{\Delta})^s_pu+V_1(x){\mid}u{\mid}^{p-2}u\\{\hfill{10}}={\ell}k^{-1}F_u(x,\;u,\;v)+{\lambda}{\alpha}(x){\mid}u{\mid}^{m-2}u,\;x{\in}{\Omega}\\M_2([u]^q_{s,q})(-{\Delta})^s_qv+V_2(x){\mid}v{\mid}^{q-2}v\\{\hfill{10}}={\ell}k^{-1}F_v(x,u,v)+{\mu}{\alpha}(x){\mid}v{\mid}^{m-2}v,\;x{\in}{\Omega},\\u=v=0,\;x{\in}{\partial}{\Omega},$$ where ${\Omega}{\subset}{\mathbb{R}}^N$ is an unbounded domain with smooth boundary ${\partial}{\Omega}$, and $0<s<1<p{\leq}q$ and sq < N, ${\lambda},{\mu}>0$, $1<m{\leq}k<p^*_s$, ${\ell}{\in}R$, while $[u]^t_{s,t}$ denotes the Gagliardo semi-norm given in (1.2) below. $V_1(x)$, $V_2(x)$, $a(x):{\mathbb{R}}^N{\rightarrow}(0,\;{\infty})$ are three positive weights, $M_1$, $M_2$ are continuous and positive functions in ${\mathbb{R}}^+$. Using variational methods, we prove existence of infinitely many high-energy solutions for the above system.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.124-128
• /
• 2022

Conventional LDO regulator external capacitors can reduce transient response characteristics such as overshoot and undershoot. However, the capacitorless LDO regulator proposed in this study applied body technology to the pass transistor to improve the transient response and provide excellent current drive capability. The operating conditions of the proposed LDO regulator are set to an input voltage that varies from 3.3V to 4.5V, a maximum load current of 200mA, and an output voltage of 3V. As a result of the measurement, it was found that when the load current was 100 mA, the voltage was 95 mV in the undershoot state and 105 mV in the overshoot state.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.9 s.351
• /
• pp.64-68
• /
• 2006

Novel system-on-package (SOP) - D technology to improve the mechanical and thermal properties of a MCM-D substrate was suggested. Based on this investigation, the two types of band pass filters for the V-band application with unique structure were designed and implemented using 2-metals, 3-BCB layers. The first type using distributed resonator had the insertion loss below 2.6 dB at 55 GHz and group delay was below 0.06 ns. For the second type with edge coupled structure, the insertion loss and group delay were 3 dB and 0.1 ns, respectively. Suggested MCM-D substrate with band pass filter can be used to evaluate mm-Wave system including flip-chip bonded MMIC.