• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.557-566
• /
• 1991

The metal V-belt behavior of a continuously variable transmission was investigated analytically and experimentally. Numerical results showed that nondimensional belt radial displacement increased in the radial inward direction for the driven pulley, while that of the driver pulley increased for the first 90 degrees of the active are and decreased with the increasing torque load. Experimental results for the belt radial displacement were in good agreement with the theoretical results. However, the absolute magnitude of the belt radial displacement was so small that the change in the belt displacement could not be measured in the experimental range except for the inlet region of the driven pulley, where the radial inward displacement was observed due to the effect of bending moment. The speed ratio-axial force relationship derived from the belt behavior analysis also showed god agreement with the experiment.

• Journal of Biosystems Engineering
• /
• 제21권2호
• /
• pp.134-145
• /
• 1996

Since the skid-steer loader is able to work for excavating, lifting and transporting load even at the narrow space, they are widely used in the regular farm and the livestock farm. The skid-steer loader normally adopts the hydrostatic transmission because the power to move the machine backward and forward should be delivered independently on both sides of wheels. Contrast to the mechanical system such as chain and belt transmissions, however, the hydrostatic transmission is less efficient in the use of energy and more difficult in the maintenance. This study was intended to investigate the feasibility of using triangular-type belt clutch and V-belt transmission for the newly developed skid-steer loader in order to overcome the problems stated in the hydrostatic transmission. In the developed triangular-type belt clutch, the centers of driving, driven and idler sheaves are arranged in the triangular shape in a plane, and V-belts were loaded loosely on three sheaves. The power is transmitted by pressing the idler connected to a lever on the loosened V-belt. Contrast to the normal belt clutch using two sheaves, the newly developed belt clutch has the characteristics of small contact-angle of the driving sheave at no bucket load and increasing contact-angle at the time of power transmission. The results of research can be summarized as follows: 1) The developed triangular-type belt clutch adopted a spring-loaded slackside idler which could transmit more power than a fixed idler could by sacrificing the belt life. The life of V-belt used in the power transmission reached at 500 hours(6 months) when the engine power of 11.8 ㎾ was transmitted. Also, it was feasible to develop the large industrial skid-loader with the V-belt transmission by using the proper set of sheaves. 2) The developed skid-steer loader changed the rotating radius and speed with bucket loads as the conventional skid steer loader did. The rotating speed was 47 deg/s at the maximum bucket load of 2.74 kN when the minimum rotating radius was 1.5m. 3) The power required in turning at the bucket load of 2.74 kN was 4 ㎾ and the slippage of V-belt was less than 1%.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.847-854
• /
• 1989

본 연구에서는 V-벨트 CVT의 핵심인 변속비-부하토오크-축력에 대한 이론적 연구에 이어 실험적 연구를 통하여 전 연구에서 구한 이론식과 비교 검토하고 V-벨트 CVT의 기초 설계자료를 얻고자한다.

• 오토저널
• /
• 제12권6호
• /
• pp.30-39
• /
• 1990

The behavior of a V-belt CVT was investigated both analytically and experimentally. It was found that as the torque load increased, the belt radial displacement increased in inward radial direction for the driven pulley while the radial displacement decreased slightly and increased for the driver pulley. The relative belt displacement for the driver was negligible compared with that of the driven. The experimental results were in good accordance with the theoretical results except for the inlet and exit region of the pulley. The speed ratio-torque load-axial force relationship derived from the belt behavior analysis also showed good agreement with the experiment. It is suggested that the results of this paper can be used as basic design informations of a V-belt CVT.

• Journal of Biosystems Engineering
• /
• 제24권2호
• /
• pp.99-106
• /
• 1999

This study was conducted to provide a direction for improving the performance of triangular-type belt clutch. The power transmission characteristics and the wear of belt were investigated for two types of pulley set theoretically and experimentally. The results of research were summarized as follows: 1) Based on the theoretical analysis for the life time of belt, the wear of belt could be reduced by increasing the sizes of driving V-pulley and tension pulley, and by decreasing the tension on V-belt. 2) The pulley set # 2 could transmit more power than the pulley set # 1 could at the same slop rate. While the slip rate was 2.36% on the pulley set # 2 at the maximum power transmission, the slip rate on the pulley set # 1 was increased up to 12.2% at the same condition. 3) From the 16 hours' fatigue test, the wear of belt used n the pulley set # 1 was observed severer than that in the pulley set#2. Also, it was found that the tensile strength of belt used in the pulley set # 2 was greater than that of belt used in the pulley set # 1.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.822-825
• /
• 2004

Continuously variable transmission (CVT) mechanisms considered here is a V-belt drive with two variable-diameter pulleys and effective diameters. One pulley was set by a mechanical link while the other was spring-loaded to provide automatic correspondence. The center distance between the two variable-diameter pulleys was fixed. Experimental studies were executed to analyze efficiencies as change of its speed ratio.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.349-357
• /
• 1990

Power transmission characteristics and speed ratio-torque load-axial force relationship for a metal V-belt CVT were investigated theoretically and experimentally. In the metal V-belt CVT drive, it was found that the power was transmitted by thrust force and that band tension should be greater than compression force between the metal blocks. The experimental results for the speed ratio-torque load-axial force relationship showed good agreement with those predicted using equations developed from theoretical considerations.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.209-218
• /
• 2002

A V belt pulley is widely used in automotive industry. More than tow pulleys in one automobile are used, such items as crankshaft, water pump, air-con compressor and power steering pump. Although the shape and usage of pulleys are very simple, the design evaluation of a pulley design is difficult because the load conditions and the installation environment are complicated. So, we formulated the design evaluation for the V belt pulley by using CAE system, which enables to develop a design automation system. By using this system, an engineer can evaluate a pulley design easily without any painstaking effort, such as consideration of the complicated loads and CAE activities. Also the system helps to accumulate the design experience of a company, which guides the optimum design based on experience.

• 오토저널
• /
• 제11권6호
• /
• pp.68-79
• /
• 1989

Dynamic characteristics for an automotive V-belt CVT with centrifugal and torque-ramp actuators was investigated by bondgraph modeling method. Ten(10) state space equations for the V-belt CVT were developed from the constructed bondgraph model and linearized for perturbation at steady state. As simulation results, speed ratio versus time curves were obtained. It was found that as the ratio of the moment of inertia of the pulleys increased, the stability of the V-belt CVT system decreased. Change in the ratio of the spring constants caused the magnitude of the change of the speed ratio, but had little effect on the settling time of the system became faster and the stability of the system improved. However, the sensitivity of the speed ratio decreased with the increasing .betha.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.799-802
• /
• 2002

Continuously variable transmission(CVT) mechanisms considered here combine the functions of a K-H-V type differential gear unit and a V-belt type continuously variable unit(CVU). As combining the functions of a K-H-V type differential gear unit and a V-belt type CVU, 24 different mechanisms are presented. Some useful theoretical formula related to speed ratio, power flow and efficiency are derived and analyzed. These mechanisms have many advantages which are the decrease of CVT size, the increase of overall efficiency, the extension of speed ratio range, and the generation of geared neutral.