• 한국세라믹학회지
• /
• 제30권9호
• /
• pp.761-767
• /
• 1993

Electrical and mechanical properties of Pb(Mg, Te, Mn, Nb)O3-PZT ceramics are investigated as a function of CeO2 addition (0 to 0.3wt%), and the output characteristics of piezoelectric transformer are also presented. The grain size decreased and the shapes of particles were more uniform with the addition of CeO2. The coercive electric field(9500V/cm), mechanical quality factor (2500) and bend strength (1065kg/$\textrm{cm}^2$) were improved by addition of CeO2 0.2wt%. After repetition of a number of stress cycles, the degradation of k33 was not found in this sample. The voltage step-up ratio (Vdc/Vrms) of piezoelectric ceramic transformer (half wavevoltage doubler, load resistor 100M.ohm) was about 950 in a linear region, its value was relatively higher than other materials.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.954-957
• /
• 2007

We analyzed conditions for fabricating zero-bias polymer-stabilized liquid crystal (PSLC) pi cells. A high curing voltage and a very low curing intensity are effective in fabricating the cell with a high bright state, a low dark state and therefore a steep T-V curve. However, the response time of the cell is slow. Finally, a dual-frequency PSLC pi cell with fast response time is developed. The obtained result reveals that the dual-frequency PSLC pi cell has a fast response of under 1ms.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제3권1호
• /
• pp.63-67
• /
• 2001

Surface morphology of perithecia of the powdery mildew fungus of mulberry, Phyllactinia corylea is described under scanning electron microscope. The perithecia have penicellate cells on the upper surface and at an average 17 acicular appendages towards the lower surface each emerging from a bulbous base. Many perithecial walls towards the base have shrunken walls. When the perithecia dry out they are pushed above the leaf surface by the acicular append-ages which then bend at the base. The bending of the appendages may be attributed to the shrinkage of lower wall cells due to loss of water.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.267-275
• /
• 2012

Austenite stainless steel 304 has properties of high resistance to corrosion and temperature changes. Therefore, this material is widely used in various of industries. However, when the material is subjected to heating and cooling cycles the forming accuracy, for example, the right angle associated with a sharp bend such as corner is lost. This phenomenon is caused by the reversion of the deformation-induced martensite into austenite when the temperature in increased. This result in misfit of a structure or an assembly, and an increase in residual stress. Hence, it is important to understand this process. In this study, to evaluate the mechanical behavior of the deformation-induced martensite and reversed austenite, a scanning acoustic spectroscope including the capability of obtaining both phase and amplitude of the ultrasonic wave (i.e., the complex V(z) curve method) was used. Then, the velocities of the SAW propagating within the specimens made in different conditions were measured. The experimental differences of the SAW velocities obtained in this experiment were ranging from 2,750 m/s to 2,850 m/s, and the theoretical difference was 3.6% under the assumption that the SAW velocity was 2,800 m/s. The error became smaller as the martensite content was increased. Therefore, the SAW velocity may be a probe to estimate the marternsite content.

• Transactions on Electrical and Electronic Materials
• /
• 제14권5호
• /
• pp.225-230
• /
• 2013

This paper presents a novel shunt radio frequency microelectromechanical system switch on a quartz substrate with stiff ribs around the membrane. The buckling effects in the switch membrane and stiction problem are the primary concerns with RF MEMS switches. These effects can be reduced by the proposed design approach due to the stiffness of the ribs around the membrane. A lower mass of the beam and a reduction in the squeeze film damping is achieved due to the slots and holes in the membrane, which further aid in attaining high switching speeds. The proposed switch is optimized to operate in the k-band, which results in a high isolation of -40 dB and low insertion loss of -0.047 dB at 21 GHz, with a low actuation voltage of only 14.6 V needed for the operation the switch. The membrane does not bend with this membrane design approach. Finite element modeling is used to analyze the stress and pull-in voltage.

• 한국재료학회지
• /
• 제6권9호
• /
• pp.885-899
• /
• 1996

초강인 AISI 4340강을 85$0^{\circ}C$에서 2시간 동안 오스테나이징 처리 후 수냉하고, 250, 400, $600^{\circ}C$에서 각각 2시간 동안 템퍼링 처리를 하였다. AISI 4340강의 인장 특성은 상온에서 측정되었다. AISI 4340강 위에 니켈 전해도금된 것과 도금되지 않은 시편의 분극 특성이 3.5wt%NaCI 수용액과 인공해수에서 측정되었다. AISI 4340강위에 니켈 전해도금된 시편은 500mV(vs. Ag/AgCI)이하의 전위에서 부식 저항이 크게 향상되었다. 그러나 1A/$\textrm{cm}^2$의 전류밀도에서 30분 이상 니켈 전해도금된 시편은 도금층에 불순물과 기공이 형성되었기 때문에 AISI 4340강의 부식 저항은 감소되었다. AISI 4340강의 수소취화형 응력부식균열을 여러 작용 응력과 음극인가전력에서 U-bend 시편을 이용하여 IN 3.5 wt% NaCI 수용액에서 조사되었고, 수소취화형 응력부식균열 거동은 주사전자현미경으로 조사되었다.

• Animal Systematics, Evolution and Diversity
• /
• 제39권4호
• /
• pp.254-263
• /
• 2023

Two feather mites, Brephosceles anatina Dubinin, 1951 (Analgoidea: Alloptidae) and Freyana anatina (Koch, 1844) (Pterolichoidea: Freyanidae), have been reported for the first time from the Eastern Spot-billed Duck, Anas zonorhyncha Swinhoe, 1866 (Anseriformes: Anatidae), in Korea. The genera Brephosceles Hull, 1934 and Freyana Haller, 1877 are new records of Korean fauna. The morphology of B. anatina is distinguished from three species of the lambda species group in having legs IV extending the level of setae e2 with the distal end of the tarsus in males, and the incision on the posterior margin of the hysteronotal shield triangular-shaped and distinctly longer than its greatest width in females. Freyana anatina is distinguished from F. nyrocae and F. obliquasetae in having setae ps1 with a rectangle bend in homeomorphic males, and setae ps1 obliquely ovate and divergent, with the inner canal going obliquely across the membranous part of these setae in females. This study provides morphological redescriptions of both feather mite species supplemented with partial sequences of mitochondrial cytochrome c oxidase subunit I(COI), based on specimens collected in Korea.

• 대한화학회지
• /
• 제39권9호
• /
• pp.685-691
• /
• 1995

결정 분자 궤도함수[EHTB]를 계산할 수 있는 VAX 컴퓨터용 EHMACC와 EHPC 프로그램을, 마이크로-소프트 포트란을 이용하는 PC로 계산할 수 있도록 변환하였다. 이 프로그램을 이용하여 perovskit 구조의 $LaNiO_3$ 단위세포와 ($2{\times}2{\times}1$)으로 확장된 구조에 대한 띠 구조를 계산한 결과, ${\Gamma}{\rightarrow}H,\;H{\rightarrow}N$ 및 $N{\rightarrow}{\Gamma}$ 방향(2차원)에서는 bend gap이 0.35eV인 반도체의 성질을 나타내고, ${\Gamma}{\rightarrow}P$와 $P{\rightarrow}N$ 방향(3차원)에서는 금속성의 성질을 나타내었다. 또 이들 결정에 관한 DOS와 COOP를 고찰한바, $LaNiO_3$에서 산소원자의 DOS는 니켈원자의 결함보다는 산소원자의 위치에 영향을 받아 서로 다른 종류의 산소원자로 존재할수 있음을 알았다.

• 한국재료학회지
• /
• 제11권3호
• /
• pp.221-226
• /
• 2001

사파이어 ($\alpha$-$Al_2$$O_3$) 단결정에 있어 basal slip (0001)1/3<1120>의 전위속도를 4점 곡강도를 이용하여, 측정하였다. 이 곡강도는 온도 $1200^{\circ}C$ 에서 $1400^{\circ}C$ 그리고 응력은 90MPa, 120MPa, 160MPa에서 행하여졌다. 전위속도는 4 점굽힘 시편의 굽힘변위속도에 의해 구하여졌다. 얻어진 전위속도를 이용하여 전위속도의 온도 및 응력 의존성에 대해 검토하였다. 전위속도의 온도의존성을 이용하여 basal slip 전위속도를 위한 활성화에너지를 구하였으며, 그 값은 대략 2.2$\pm$0.4eV이었다. 한편, 전위속도의 응력의존성을 나타내는 응력지수 m은 2.0$\pm$0.2이었다.

• Restorative Dentistry and Endodontics
• /
• 제18권1호
• /
• pp.1-26
• /
• 1993

The purpose of this study was to investigate the effect of acid etching on the surface appearance and fracture toughness of five glass ionomer cements. Five kinds of commercially available glass ionomer cements including chemical curing filling type, chemical curing lining type, chemical curing metal reinforced type, light curing tilling type and light curing lining type were used for this study. The specimens for SEM study were fabricated by treating each glass ionomer cement with either visible light curing or self curing after being inserted into a rubber mold (diameter 4mm, depth 1mm). Some of the specimens were etched with 37% phosphoric acid for 0, 15, 30, 60, go seconds, at 5 minutes, 1 hour and 1 day after mixing of powder and liquid. Unetched ones comprised the control group and the others were the experimental groups. The surface texture was examined by using scanning electron microscope at 20 kV. (S-2300, Hitachi Co., Japan). The specimens for fracture toughness were fabricated by curing of each glass ionomer cement previously inserted into a metal mold for the single edge notch specimen according to the ASTME399. They were subjected to a three-point bend test after etching for 0, 30, 60, and 90 seconds at 5 minutes-, 1 hour-and 1 day-lapse after the fabrication of the specimens. The plane strain fracture toughness ($K_{IC}$) was determined by three-point bend test which was conducted with cross-head speed of 0.5 mm/min using Instron universal testing machine (Model No. 1122) following seven days storage of the etched specimens under $37^{\circ}C$, 100% humidity condition. Following conclusions were drawn. 1. In unetched control group, crack was present, but the surface was generally smooth. 2. Deterioration of the surface appearance such as serious dissolving of gel matrix and loss of glass particles occured as the etching time was increased beyond 15 s following Immediate etching of chemical curing type of glass ionomer cements. 3. Etching after 1 h, and 1 d reduced surface damage, 15 s, and 30s etch gave rough surface appearance without loss of glass particle of chemical curing type of glass ionomer cements. 4. Light curing type glass ionomer cement was etched by acid, but there was no difference in surface appearances according to various waiting periods. 5. It was found that the value of plane stram fracture toughness of glass ionomer cements was highest in the light curing filling type as $1.79\;MNm^{-1.5}$ followed by the light curing lining type, chemical curing metal reinforced type, chemical curing filling type and chemical curing lining type. 6. The value of plane stram fracture toughness of the chemical curing lining type glass ionomer cement etched after 5 minutes was lower than those of the cement etched after 1 hour or day or unetched (P < 0.05). 7. Light curing glass ionomer cement showed Irregular fractured surface and chemical curing cement showed smooth fractured surface.