• Korean Journal of Crystallography
• /
• v.17 no.1
• /
• pp.24-32
• /
• 2006

The microwave dielectric properties of $Zn_3Nb_2O_8\;with\;V_2O_5$ addition were investigated. The addition of $V_2O_5$ enhanced the sinterability of $Zn_3Nb_2O_8$, which resulted in high density of $Zn_3Nb_2O_8$ ceramic greater than 95% of the theoretical value when sintered at $900^{\circ}C$ for 4 hours. X-ray diffraction analysis of sintered $Zn_3Nb_2O_8$ ceramic showed no second phase with $V_2O_5$ addition. Dielectric permittivity(${\varepsilon}_r$) and quality factor($Q{\times}f$) varied with both density at different sintering temperature and $V_2O_5$ addition. Dielectric permittivity, quality factor and temperature coefficient($T_{cf}$) of the two mole of $V_2O_5\;added\;Zn_3Nb_2O_8$ that was sintered at $900^{\circ}C$ were 21.4, 40,000, $-54ppm/^{\circ}C$, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.6
• /
• pp.281-286
• /
• 2008

In the 1.1 Mn steel containing boron, effects of the 0.1 V addition and processing condition were studied. In the $550^{\circ}C$ interrupted cooling where the main structure is (ferrite + pearlite), the impact toughness decreased as the tensile strength increased by the 0.1 V addition. The $800^{\circ}C$ rolling including two step rolling of $800-770^{\circ}C$, exhibited better strength-toughness balance, as compared to the $770^{\circ}C$ rolling. This seems to be kind of conditioning effect at higher temperature, e.g., more uniform deformation effect. In the accelerated cooling after the $750^{\circ}C$ rolling in a dual phase range, the impact toughness was enhanced, despite a large increase in tensile strength. This is believed to be related to the change of main structure from (ferrite + pearlite) to (ferrite + bainite).

• Journal of the Korean Ceramic Society
• /
• v.20 no.3
• /
• pp.193-198
• /
• 1983

This experiment has been carried out for the purpose of investigating the effect of $V_2O_5$ and $H_3BO_3$ additives on sintering of magnesium oxide over the temperature range of 1300-150$0^{\circ}C$ MgO powder has been obtained by calcin-ing extra reagent grade magnesium carbonate(basic) at 90$0^{\circ}C$ for 30 minutes. The specimens were prepared by compression with pressure of 700Kg/cm2 then fired at 1300-150$0^{\circ}C$ for 0-5hrs. Sintering behaviour and microstructure of fired specimens were examined. Densification rates obeyed the equation D=K 1n t+C. The ratio of density in case of addition of $V_2O_5$ to theoretical density of pure periclase was 95-99% Activation energy of densification in case of $V_2O_5$ addition was 30.15 Kcal/mole. The range of average grain size in case of addition of $V_2O_5$ was 40-50$\mu\textrm{m}$. $H_3BO_3$ addtivie had not an effect on densification of MgO.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.676-680
• /
• 2003

In this study, to develop the low temperature sintering ceramics for piezoelectric transformer, PSN-PNN-PZT system ceramics were manufactured as a function of V$_2$O$_{5}$ addition, that is the low melting point oxide. Its dielectric and piezoelectric characteristics were investigated. With increasing the amount of V$_2$O$_{5}$ addition, electromechanical coupling factor(kp) and mechanical quality factor(Qm) were decreased. For piezoelectric transformer application, the 0.1wt% V$_2$O$_{5}$ added specimen sintered at 1,00$0^{\circ}C$ showed the proper value of $\varepsilon$r=1,590, kp=0.51 and Qm=748.m=748.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.5
• /
• pp.297-303
• /
• 1998

The influences of vanadium addition on the cavitation erosion resistance pf Fe-Cr-Ni-Si-C hardfacing alloy were investigated using a vibratory apparatus up to 30 hrs. It was shown that 1wt.%V additioned alloy improved the resistance to cavitation damage. However, further increase in V content up to 2wt.% reduced the cavitation erosion resistance. It was considered that the addition of V developed the cavitation erosion resistance by reducing the stacking fault energy of Fe-Cr-Ni-Si-C alloy. However, the further increase in V content seemed to reduce the cavitation erosion resistance by increasing the matrix/carbide interfacial area, which was the preferential sites of the cavitation damage.

• Analytical Science and Technology
• /
• v.5 no.2
• /
• pp.203-211
• /
• 1992

Fracture behavior and martensite substructure of Ni-36.5at.%Al alloy were investigated with the addition of vanadium which is known as scavenging element of grain boundary. The fracture surfaces were examined by scanning electron microscopy and the EDX spectrometer was applied for composition analysis of fracture surfaces. The substructure of martensite was studied by transmission electron microscopy. By addition of vanadium, fracture surfaces show mixed modes of intergranular and transgranular fracture and more Al content is found on the grain boundaries. For Ni-36.5at.%Al alloy, the planar faults observed in the martensite plates are the internal twins. By increasing the vanadium content, the modulated structure with stacking faults and dislocations dominates while the twinned martensite disappears. The stacking fault is determined to be extrinsic due to the substitution of V for Al. It is concluded that the segregation of sulfur on the high-energy state stacking fault area suppresses the intergranular fracture.

• Journal of Hydrogen and New Energy
• /
• v.10 no.1
• /
• pp.59-69
• /
• 1999

AlN thin films were fabricated by reactive sputtering for the application of MIS devices with Al/AlN/Si structure. It has investigated the surface morphology change, I-V characteristics, C-V characteristics, and chemical composition of AlN films with the intriducing time of hydrogen on the fixed deposition condition(RF power: 150W, sputtering pressure: 5mTorr, flow rate ratio of $Ar/N_2=1$, hydrogen concentration: 5%). By addition of the hydrogen the deposition rate decreased drastically whereas the surface morphology changed little. It has been found from the analysis of I-V and C-V characteristics curves that the films deposited with hydrogen addition in initial stage had lower leakage current density, lower flat band voltage and hystersis profile when compared with those with hydrogen addition in last stage. The oxygen concentration in AlN films decreased with addition of hydrogen gas, which suggesting a profitable role in the insulation and C-V characteristics of AlN films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.11
• /
• pp.975-978
• /
• 2003

The microwave dielectric properties and the microstructures on B $i_{0.97}$T $m_{0.03}$Nb $O_4$ doped with $V_2$ $O_{5}$ were systematically investigated. B $i_{0.97}$T $m_{0.03}$Nb $O_4$ ceramics sintered at 920-96$0^{\circ}C$ were mainly consisted of orthorhombic and triclinic phases after addition of $V_2$ $O_{5}$. The apparent density increased slightly with increasing the $V_2$ $O_{5}$ addition. The dielectric constants($\varepsilon$$_{r}$) also increased with $V_2$ $O_{5}$ addition(30-45). The Q${\times}$ $f_{0}$ values measured on B $i_{0.97}$T $m_{0.03}$Nb $O_4$ ceramics doped with $V_2$ $O_{5}$ were between 2,000 and 12,000[GHz] when the sintering temperatures were in the range of 920-960[$^{\circ}C$]. It was confirmed that the temperature coefficient of the resonant frequency($\tau$$_{f}$) can be adjusted from a positive value of +10ppm/$^{\circ}C$ to a negative value of -15ppm/$^{\circ}C$ by increasing the amount of $V_2$ $O_{5}$ Based on our experimental results, the B $i_{0.97}$T $m_{0.03}$Nb $O_4$(added $V_2$ $O_{5}$) ceramics can be applied to multilayer microwave devices at low sintering temperatures.ng temperatures.emperatures.ratures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.350-353
• /
• 2002

The microwave dielectric properties and the microstructures on $Bi_{0.97}Nb_{0.03}O_{4}$doped with $V_{2}O_{5}$ were systematically investigated. $Bi_{0.97}Tm_{0.03}Nb_{0.03}O_{4}$ ceramics sintered at $920-960^{\circ}C$were mainly consisted of orthorhombic and triclinic phases after addition of $V_{2}O_{5}$. The apparent density increased slightly with increasing the $V_{2}O_{5}$ addition. The dielectric $constants(\varepsilon_r)$ also increased with $V_{2}O_{5}$ addition(30-45). The $Q{\times}f_0$ values measured on $Bi_{0.97}Tm_{0.03}NbO_4$ ceramics doped with $V_{2}O_{5}$ were between 2,000 and 12,000[GHz] when the sintering temperatures are in the range of $920-960[^{\circ}C]$. It was confirmed the temperature coefficient of the resonant $frequency(\tau_f)$ can be adjusted from a positive value of $+10[ppm/^{\circ}C]$ to a negative value of $-15ppm/^{\circ}C$ by increasing the amount of $V_{2}O_{5}$. Based on our experimental results, the Bi0.97Tm0.03NbO4(added V2O5) ceramics can be applied to multilayer microwave devices at low sintering temperatures.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1213-1220
• /
• 2018

The effects of Cr and Fe addition on the mechanical properties of Ti-6Al-4V alloys prepared by direct energy deposition were investigated. As the Cr and Fe concentrations were increased from 0 to 2 mass%, the tensile strength increased because of the fine-grained equiaxed prior ${\beta}$ phase and martensite. An excellent combination of strength and ductility was obtained in these alloys. When the Cr and Fe concentrations were increased to 4 mass%, extremely fine-grained martensitic structures with poor ductility were obtained. In addition, Fe-added Ti-6Al-4V resulted in a partially melted Ti-6Al-4V powder because of the large difference between the melting temperatures of the Fe eutectic phase (Ti-33Fe) and the Ti-6Al-4V powder, which induced the formation of a thick liquid layer surrounding Ti-6Al-4V. The ductility of Fe-added Ti-6Al-4V was thus poorer than that of Cr-added Ti-6Al-4V.