• 한국분말재료학회지
• /
• 제7권3호
• /
• pp.131-136
• /
• 2000

The effect of tempering temperature on the three point bending fatigue behavior of a P/M high speed steel JYPS-23 (1.28% C, 4.20% Cr, 6.40% W, 5.00% Mo, 3.10% V, bal. Fe) was investigated. The number of cycles to failure of the specimen austenitized at $1175^{\circ}C$ drastically increased with increasing tempering temperature. As tempering temperature increased from 500 to $620^{\circ}C$, the volume fraction and average size of carbides (MC or M6C) did not significantly changed, while hardness decreased drastically. The reduced hardness is due to the softening of matrix, which increased the resistance of the fatigue crack propagation. For a practical application, powder compacting test were also conducted with the P/M high speed steel punches tempered at 500, 580, and $620^{\circ}C$. The number of compacting cycles to failure of the punches also increased with increasing tempering temperature.

• Design & Manufacturing
• /
• 제15권3호
• /
• pp.19-25
• /
• 2021

The bending process of a press die is to bend a flat blank to the required angle. There are V-bending, U-bending, Z-bending, O-bending etc. for bending processing, and the basic principle of calculating the unfolding length of die processing is used as the neutral plane length. Since the constant of the length value of the neutral surface is different depending on the type of bending, it is impossible to accurately calculate it. In particular, Z-bending processing is performed twice, and it is set on the upper and lower surfaces of the blank, and bending processing occurs at the same time as the upward and downward bending, and the elongation of the material occurs and the material increases. It is not possible to check with the calculated value, and it occurs in many cases where the mold is modified after start-up. This study aims to minimize die modification by developing a formula to calculate the development length of Z-bend.

• 대한조선학회논문집
• /
• 제37권3호
• /
• pp.99-109
• /
• 2000

본 연구에서는 대파고 파랑 중을 항해하는 선박의 슬래밍 충격에 대한 선체 전체의 동적 탄성응답 해석법을 개발하였다. 선체구조는 전단효과를 고려하는 박판보 유한요소이론을 활용하였으며, 선체 각 단면에 작용하는 유체력은 통상의 선형 운동체 이론에 덧붙여 물체 경계의 비선형성을 고려하여 추정하였다. 즉 매 순간 선체와 파 입자간의 접수 형상을 고려하는 비선형 유체력 추정법을 모멘텀 슬래밍 이론에 근거하여 정식화하였다. 개발된 해석법의 검증을 위해 V형 단면 선형과 S-175 선형 모델을 대상으로 수치해석을 수행하였다. 시간 영역에 있어 각 단면에서의 파면에 대한 상대 변위 성분과 속도 성분들을 계산하였으며, 선체 중앙 단면에서의 굽힘 모멘트 값의 시간이력을 검토하였다.

• 동력기계공학회지
• /
• 제12권3호
• /
• pp.50-54
• /
• 2008

Various Sialon ceramics were fabricated by hot-pressing mixtures of $Si_3N_4$ with additive $Y_2O_3$ and $Al_2O_3$. The polished specimen of SiAlON $I{\sim}III$ went on increasing in strength by heat treatment, heat treated non-polished specimen were similar or up to polished specimen in strength. The polished specimen of both SiAlON IV and V showed a very high strength, but were not Increasing of strength by heat treatment. All specimens were fractured on the surface and at the inner flaws. Surface fractures were initiated from the polished surface flaw and corner flaw. Inner fractures were initiated from an internal defect.

• 대한기계학회논문집A
• /
• 제30권3호
• /
• pp.269-278
• /
• 2006

This paper proposes slip line fields for bending of unequally notched specimens in plane strain that have a sharp crack in one side and a sharp V-notch in the other side. Depending on the back angle, two slip line fields are proposed, from which the limit moment and crack tip stress fields are obtained as a function of the back angle. Excellent agreement between slip line field solutions with those from detailed finite element limit analysis based on non-hardening plasticity provides confidence in the proposed slip line fields. One interesting point is that, for the unequally notched specimen, the difference between the crack tip triaxial stress for tension and that for bending increases significantly with increasing the back angle. This suggests that such a specimen could be potentially useful to investigate the crack tip constraint effect on fracture toughness of materials. In this respect, the possibility of designing a new toughness testing specimen with varying crack tip constraint is discussed.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 추계학술대회 논문집(Proceeding of the KOSME 2001 Autumn Annual Meeting)
• /
• pp.71-79
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel(JISG4081-SUP ,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• Applied Microscopy
• /
• 제7권1호
• /
• pp.45-49
• /
• 1977

용탕의 온도는 탄소의 비율을 높이기 위하여 $1500^{\circ}C$ 이하로 해야 하며, 주입온도는 $1460^{\circ}C$ 내외가 적당하다. 주조상태에서 소지의 침상석출물은 orthorhombic $(Fe,\;Mn)_3C$로 판명되었다. 냉간압연비는 클수록 결정이 미세화되고 또한 경도도 증가하였다. 표면탈탄이 얼어 나면 표면층에 martensite가 형성되어 성형하기가 어려우므로 argon 분위기를 쓰는 것이 좋았다. 두께 1 mm 판재의 경우 수인처리 온도가 $950^{\circ}C$ 이하일 때 탄화물 stringer 가 나타났고, $1020^{\circ}C$ 에서 30 분간 가열했을 때 탄화물이 의 소지에 고용되었다. C 함량이 클수록 인장강도와 연신률이 증가하였다. Ni, Cr 및 V 을 미량 첨가했을 때 인장강도 및 연신률이 커졌으며 또한 굽힘성도 좋았다.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.185-192
• /
• 2003

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to Dow the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7, SAE 9254, DON 50CrV4) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of hish hardness.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.366-372
• /
• 2002

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface deject as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know tile influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at tire case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1067-1069
• /
• 2004

22.9[kV]/50[MVA]/30[m] HTS transmission power cable has been developed and tested at Korea Electrotechnology Research Institute and LG Cable Company by 21 century center for applied superconductivity technology. It is necessary to measure of critical current degradations, AC loss, insulation test and etc at the HTS cable development. This paper is analyzed characteristics that critical current of HTS cable bending condition according to this paper. We will be able to decide the diameter of drum which HTS cable is wound around and minimum curvature radius of HTS cable from results of this research.