• 한국도로학회논문집
• /
• 제17권1호
• /
• pp.91-98
• /
• 2015

PURPOSES : Although signalized intersections have been considered the best way to control traffic volume in urban areas for several decades, roundabouts are currently being discussed as an alternative way to control traffic volume, especially when traffic is light. Because a roundabout's efficiency depends on the load geometry as well as the traffic volume, design guidelines for roundabouts are recommended only if the incoming traffic volume is very low. It is rare to substitute a roundabout for an existing signalized intersection in urban areas. This study aims to estimate the benefits from the transformation of an existing signalized intersection into a roundabout in an urban area. When there is a more moderate volume of traffic, roundabouts can be effectively used by optimizing signals located at an approaching roadway. METHODS : The methodologies of this paper are as follows: First, a signalized intersection was analyzed to determine the traffic characteristics. Second, the signalized intersection was transformed into a roundabout using VISSIM microscopic traffic simulation. Then, we estimated and analyzed the effects and the performance of the roundabout. In addition, we adjusted a method to improve the benefits of the transformation via the optimization of signals located at an approaching road to control the incoming traffic volume. RESULTS : The results of this research are as follows: The signal-optimized roundabout improved delays compared with the signalized intersection during the morning peak hour, non-peak hour, and evening peak hour by 1.78%, 12.45%, and 12.72%, respectively. CONCLUSIONS : According to the simulation results of each scenarios, the signal-optimized roundabout had less delay time than the signalized intersection. If optimized signal control algorithms are installed in roundabouts in the future, this will lead to more efficient traffic management.

• 한국항해항만학회지
• /
• 제26권1호
• /
• pp.85-94
• /
• 2002

본 연구에서는 문헌조사를 통해 국내외 연안의 경관관리제도를 분석하였으며 먼저 연안의 경관관리에 앞서 가는 미국과 일본 연안도시에서 연안의 경관관리제도를 분석하였고 다음으로 우리나라 연안의 경관관리제도와 부산 연안의 경관관리제도의 현황과 문제점을 분석하였다. 이를 바탕으로 현행 관리체계 내에서 부산 연안의 경관관리제도 개선 방안을 제시하고 동시에 연안의 경관관리제도의 장기적인 개선 방향을 제시하였다. 본 연구결과 연안의 경관은 육지 경관과 바다 경관이 어우러져 구성되기 때문에 도시계획측면에서 보다는 연안관리차원에서 통합적인 관리가 필요하다 이를 위해 연안관리법을 기반으로 지역별로 연안경관관리조례를 만들어 구체적인 연안의 경관관리가 이루어져야 한다. 특히 연안의 경관 특성에 따라 연안경관관리지역을 설정하고 그 안에 경관보전지구, 경관회복지구, 경관계획지구를 두어 지구별로 관리하며 지역의 경관종합계획과 지구별 경관계획지침을 세워야 한다

• 한국ITS학회 논문지
• /
• 제21권1호
• /
• pp.123-140
• /
• 2022

지하도로의 운전자 주행행태는 지상도로와는 다르기 때문에 이를 반영한 도로설계가 필요하지만, 국내 도시지역 지하도로 설계지침은 대부분 지상도로의 설계기준을 준용하여 설계방법을 설명하고 있다. 본 연구에서는 주행 시뮬레이터를 활용하여 도심 지하도로 유출연결로 접속부의 운전자 주행행태를 분석하였다. 지하도로 및 지상도로 환경이 대조될 수 있는 시나리오를 설정하여 가상주행실험을 수행하였고, 세부 구간별로 주행행태 데이터의 비교·분석과 통계적 유의성을 검토하였다. 그 결과, 지하도로에서의 주행속도는 상대적으로 낮고 차로 횡적 이격거리는 인접한 터널 벽체로부터 멀어지려는 행태를 보였다. 이러한 결과를 바탕으로 지하도로 유출연결로 접속부에서 운전자의 주행안전성을 향상시킬 수 있는 설계방향과 시사점을 제시하였다.

• 의료ㆍ복지 건축 : 한국의료복지건축학회 논문집
• /
• 제17권4호
• /
• pp.57-68
• /
• 2011

The purpose of this study is to provide the planning factors of housing for the disabled and elderly based on the inclusive housing design as sustainable neighborhood. The goal of inclusive design is to make buildings and communities more livable for all type of people. Inclusive design should embrace other good design goals and reinforce them, not work against them. To carry out this purpose, we should proceed in the following way: First, we deducted the four design factors (the basic, recommendable, adaptable, and residential factors) by reviewing the characteristics of inclusive housing concepts. Second, we analyzed the related foreign design standards and guidelines such as the ICC/ANSI A117.1 Type C Units (the United States, 2009), Lifetime Standard (the United Kingdom, 2010), and Livable Housing Design Guideline (the Australian, 2010) through four design factors based on inclusive design concepts. Finally, we suggested the housing design factors for the disabled and the elderly in Korea. To conclude, we can make the followings: It is important basic factor that the bedroom and bathroom layout closed to each other. Also, the bedroom has the proper height of light switches, outlets, and windows. The recommendable factors take into consideration stairs and ramp, if existent. The adaptable factors are closely related to domestic housing culture as well as residential factors. Proceeding from this fact, the livability for people with disabilities and older requires accessibility and adaptability that take into account public and efficiency considering the current trend of housing development and urban planning.

• 대한가정학회지
• /
• 제47권10호
• /
• pp.97-108
• /
• 2009

As one of the conservation strategies, the city of Jeonju established regulations to conserve and revitalize the Hanok village as an attractive tour site. Some of old traditional houses were renovated into traditional inns. A couple of traditional houses were additionally built for lodging houses. The need for urban rehabilitation and adaptive re-use has been growing in Jeonju province. The purpose of this study was to examine how the traditional houses were converted into lodging places balancing the conflict issues such as preserving the unique characteristics of Hanok and updating functional requirement of modern lodging in terms of sustainable reuse and development. For this study, site visits and intensive interview with the owners of the seven traditional lodges were conducted. There was lack of guidelines and strategies renovation or rehabilitation of Hanok as lodging facility for sustainable use and revitalization of city. For the seven traditional Hanok inns, layout of rooms characterized as separate and disconnected, while traditional houses were open, flexible and connected regarding room arrangement. In addition, for sustainable development, the living environment of the community should be secured and align with developing strategies of the area.

• 국제초고층학회논문집
• /
• 제7권4호
• /
• pp.313-325
• /
• 2018

Concrete-filled steel tubular (CFST) members are commonly used as composite columns in modern construction. However, the current guidelines for members' fire design (EN1994-1-2) have been proved to be unsafe in case the relative slenderness is higher than 0.5. In addition, the simplified design methods of Eurocode 4 are limited to circular and square CFST columns, while in practice columns with rectangular and elliptical hollow sections are being increasingly used because of their architectural aesthetics. In the last years a large experimental research has been carried out at Coimbra University on the topic. They have been tested concrete filled circular, square, rectangular and elliptical hollow columns with restrained thermal elongation. Some parameters such as the slenderness, the type of cross-section geometry as well as the axial and rotational restraint of the surrounding structure to the column have been tested in order to evaluate their influence on the fire resistance of such columns. In this paper it is evaluated the influence of the boundary conditions (pin-ended and semi-rigid end-support conditions) on the behavior of the columns in case of fire. In these tests it could not be seen a marked effect of the tested boundary conditions but it is believed that the increasing of rotational stiffness increases the fire resistance of the columns.

• Membrane and Water Treatment
• /
• 제10권1호
• /
• pp.67-74
• /
• 2019

Apparent changes in the natural hydrologic cycle causing more frequent floods in urban areas and surface water quality impairment have led stormwater management solutions towards the use of green and sustainable practices that aims to replicate pre-urbanization hydrology. Among the widely documented applications are infiltration techniques that temporarily store rainfall runoff while promoting evapotranspiration, groundwater recharge through infiltration, and diffuse pollutant reduction. In this study, a laboratory-scale infiltration device was built to be able to observe and determine the factors affecting flow variations and corresponding solids removal through a series of experiments employing semi-synthetic stormwater runoff. Results reveal that runoff and solids reduction is greatly influenced by the infiltration capability of the underlying soil which is also affected by rainfall intensity and the available depth for water storage. For gravel-filled structures, a depth of at least 1 m and subsoil infiltration rates of not more than 200 mm/h are suggested for optimum volume reduction and pollutant removal. Moreover, it was found that the length of the structure is more critical than the depth for applications in low infiltration soils. These findings provide a contribution to existing guidelines and current understanding in design and applicability of infiltration systems.

• 한국콘텐츠학회논문지
• /
• 제12권11호
• /
• pp.458-468
• /
• 2012

본 연구의 목적은 U-City와 Eco City에서 파생된 U-Eco City의 계획요소를 도출하고, 이들 계획요소로부터 도출된 서비스의 공간적용성을 분석하는데 있다. U-Eco City 서비스의 공간적용성을 분석하기 위하여 먼저 도시공간을 '건물', '가로', '시설' 그리고 '지구'의 4개 위계로 구분하였다. 이들 공간은 각각의 용도 등에 따라 보다 세분화한 후 분석에 적용하였다. U-Eco City의 계획요소 중 U-City의 계획요소는 도시의 활동에 따라 생활(Living), 일(Working), 이동(Moving) 및 놀이(Playing) 부문별로 총 228개 단위 서비스를 도출하였다. Eco City 서비스는 태양과 빛, 물, 녹지, 공기와 바람, 토지와 토양, 식생과 생태 등 자연요소와 에너지, 환경오염, 소음, CO2 및 가스, 환경폐기물 그리고 경관 등 자연요소 55개 부문에 대하여 도출하였다. U-Eco City 각 계획요소의 공간적용성은 U-City 및 Eco City 계획요소가 어떤 공간단위에 적용되는지를 교차분석(Cross-tabulation)을 통해 분석하였다. 분석결과, U-City 계획요소는 도시공간 중 '지구' 단위(35.7%), Eco City 계획요소는 '건물' 단위(38.8%)에 적용될 가능성이 가장 높은 것으로 분석되었으며, 각 계획요소의 공간적용성은 공간의 위계에 따라 각각 다르게 나타났다. 따라서 U-City와 Eco City계획요소가 공간에서 융합된 U-Eco City를 구현하기 위해서는 공간위계에 따른 차별적 계획요소를 도입하고 이에 대한 구체적 계획 및 설계지침이 제시되어야 할 것으로 판단된다.

• KIEAE Journal
• /
• 제16권6호
• /
• pp.39-50
• /
• 2016

Purpose: The purpose of this study is to be performed with studio-type housings among urban life-type housings to investigate the physical characteristic and crime-related factors of studios from the viewpoint of the basic principles of crime prevention through environmental design (CPTED). Method: Eight CPTED guidelines available in Korea were reviewed to select 20 planing factors for actual condition investigation. Five single households in studio-type housings in Gwanak-gu, Seoul, were chosen according to the subject screening criteria to perform the actual condition investigation. Results: First, a lighting plan around a building for natural surveillance should consider the building location, relation with the front road, and surrounding facilities. In a building of a piloti structure, the parking lot and the building gate should be arranged in a manner that enables natural surveillance. Second, the shape of the corridors in studio-type housings should be considered to plan the installation of a lighting at the door of each household, the installation of a viewer window at the door of each household, and the arrangement of the elevator. Third, to support access control, an access control system having the function of video and voice communication is recommended to be installed at the building gate. Criteria for the type of security windows and the floors on which security windows should be installed, and the regulations about the CCTV installation inside and outside the building should be prepared. Fourth, to enhance territoriality in parking lots, ground patterns, parking lot gate, and signs may be installed. Fifth, in view of effective utilization and maintenance, lighting facilities should be installed to increase the usability of ground parking lots, and relevant installation criteria should be prepared regarding the type, number, and brightness of the lightings.

• 대한교통학회지
• /
• 제30권4호
• /
• pp.21-32
• /
• 2012

도로 중앙에 위치한 버스전용차로는 일반차로상에서 복수의 차로변경을 통해 일반차로의 가장왼쪽 차로에서 버스전용차로로 진입할 수 있다. 성공적인 버스전용차로 운영을 위해서 특히 주목해야 할 사항은 도로 진입구에서 도로중앙에 위치한 버스전용차로 진 출입구간까지의 적당한 차로변경구간길이이다. 차로변경길이 증감에 대한 안전민감도 분석을 통해 적절한 차로변경구간길이에 대한 지침을 도출할 수 있다. 하지만 차로변경구간길이에 대한 지침을 도출하기 위한 과정은 다양한 교통량 및 차로변경구간길이와 안전과의 상관관계 현장데이터가 필요하기 때문에 어려움이 있다. 본 연구는 미시적 교통시뮬레이션 프로그램(VISSIM)을 통해 차량의 흐름을 시뮬레이션하고, 시뮬레이션된 각 차량의 궤도(trajectory) 데이터를 기초로 Surrogate Safety Assessment Model (SSAM)을 이용하여 차로변경구간길이 증감에 따른 차량들간의 상충횟수(또는 안전의 정도)를 조사한다. 그리고 차로변경구간길이와 상충횟수의 관계를 다중선형회귀모형으로 정립한다. 마지막으로 다중선형회귀모형을 통해 차로변경구간길이에 대한 디자인 지침을 도출한다. 디자인 지침은 차로변경 교통량이 증가할수록 안전을 확보하기 위해 증가된 차로변경길이가 요구됨을 보여준다.