• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.647-657
• /
• 2006

Probabilistic Risk Assessment considering statistically random variables is performed for the preliminary design of a Cable Stayed Bridge, which is Prestressed Concrete Bridge consisted of cable and plate girders, based on the method of Working Stress Design and Strength Design. Component reliabilities of cables and girders have been evaluated using the response surface of the design variables at the selected critical sections based on the maximum shear, positive and negative moment locations. Response Surface Method (RSM) is successfully applied for reliability analyses for this relatively small probability of failure of the complex structure, which is hard to obtain through Monte-Carlo Simulations. or through First Order Second Moment Method that can not easily calculate the derivative terms of implicit limit state functions. For the analysis of system reliability, parallel resistance system consisting of cables and plate girder is changed into series connection system and the result of system reliability of total structure is presented. As a system reliability, the upper and lower probabilities of failure for the structural system have been evaluated and compared with the suggested prediction method for the combination of failure modes. The suggested prediction method for the combination of failure modes reveals the unexpected combinations of element failures in significantly reduced time and efforts compared with the previous permutation method or system reliability analysis method, which calculates upper and lower bound failure probabilities.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.5
• /
• pp.698-713
• /
• 1999

Adherence of Candida albicans(C. albicans) to the surface of a denture is believed to be an initial and essential step in the formation of denture-induced stematitis. Previous studies have provided enormous infomation on the relationship between composition of palatine gland/parotid saliva and upper denture stomatitis. Relatively little information is available on the correlation between lower denture stomatitis and sublingual-submandibular ( SLSM ) saliva. The plaque samples were collected from the two sites($100mm^2$) on the inner surface of lower partial denture corresponding to the stematitis and healthy region of the lower partial dentures of 12 denture stomatitis patients and 6 nor-mal persons who wore lower partial dentures. The samples were plated to isolate C. albicans on a selective Saboraud's dextrose agar plate and the isolates were identified by germ tube test and gram staining. The subjects were divided into group I (stomatitis with C. albican), group II (lesion without C. albicans), group III (no lesion but C. albicans), and group IV (normal and healthy denture wearer). Individual SLSM saliva($20{\mu}g$ of protein) was analyzed by SDS-PAGE (SDS -poly-acrylamide gel electrophoresis) with Coomassie brilliant blue and PAS(Periodic Acid Schinff) stain-ing. The salivary proteins separated in the polyacryamide gels were subjected to immunoblot anaysis using anti-lactoferrin, anti-sIgA, and anti-secretory component of sIgA. In this study using custom made acrylic denture resin beads(5mm in diameter) coated with stimulated individual SLSM saliva, the binding ability of individual C. albicans strains to the beads was observed. Levels of C, albicans adhered to the acrylic resin beads were determined by measuring the optical density of the bound C. albicans to the beads at 580nm. The results showed that a higher number of C. albicans was observed in the lesion site than healthy site. The saliva of group I contained more high molecular weight glycoprotein(mucin, MGI) as compared to group II, III and IV. And lactoferrin and sIgA affected to the binding ability of C. albicans to acylic resin beads. Binding ability of individual C. albicans to the acrylic resin coated with respective individual saliva was found to be greater in group I than the other 3 groups. And when bound cells of C. albicans isolated from individual subject #2 to the saliva coated beads were used binding ability of subject #2 saliva coated beads was founed to be greater than the other sutjects. These results suggested that denture induced stomatitis is related to individual patient's salivary protein composition, especially MG-1. Future studies will be directed toward saliva exam-ination of patients who have general disease and analysis of pellicles formed on prosthesis with respect to oral disease.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.3 s.36
• /
• pp.451-461
• /
• 1998

The solution of anisotropic plate via the classical methods is limited to relatively load and boundary conditions. If these conditions are more complex, the analysis becomes increasingly tedious and even impossible. For many plate problems of considerable practical interest, analytic solutions to the governing differential equations cannot be found. Among the numerical techniques presently available, the finite difference method and the finite element method are powerful numerical methods. The objective of this paper is to compare with each numerical methods for the buckling load and modes of anisotropic composite laminated plates considering shear deformation. In applying numerical methods to solve differential equations of anisotropic plates, this study uses the finite difference method and the finite element method. In determining the eigenvalue by Finite Difference Method, this paper represent good convergence compared with Finite Element Method. Several numerical examples and buckling modes show the effectiveness of various numerical methods and they will give a guides in deciding minimum buckling load and various mode shapes.

• The KIPS Transactions:PartC
• /
• v.11C no.2
• /
• pp.213-218
• /
• 2004

Recently MIP becomes more important for the macro mobility support in the emergence of the global system such as IMT-2000. However this Protocol suffers from many weaknesses on the location management. MIPv4 regional registration is presented for the local registration of MNs. MIPv6 can benefit from the reduced mobility signaling with external networks by employing a local MAP, that is called HMIPv6. The total signaling cost of HMIPv6 is rapidly increased by the number of CNs of an MN when the MN moves around between MAPs. In this paper, we propose a new location management scheme in MIPv6 that reduces the total signaling cost in the location update based on HMIPv6 Here the MN does not send the BU to CNs and HA when it moves around between MAPs. Instead it informs the current location by transferring the modified BU to the previous MAP. According to the results of the performance analysis, we determine the upper bound for the number of forwarding links allowed among adjacent MAPs without the BU information.

• Journal of Biosystems Engineering
• /
• v.16 no.2
• /
• pp.133-141
• /
• 1991

This study was undertaken to investigate the structural and configurational characteristics of the tailings return-unit in the commercially available head-feed combines and to study the aero-dynamical behavior of the tailings in the units. The mathematical model of the motion of tailings in the thrower casing was developed and the simulated trajectories for different type of units was analyzed to compare with the measured ones. The air-stream velocity profile in various locations along the tailings returning duct was measured to find the effect of configurational characteristics and blade tip speed. The results of the study are summerized as follows. 1. The ejecting angle, which is the angle between the direction of the particle velocity ejecting from the blade and the horizontal axis, was found to be about $66^{\circ}$ in both the simulation and experiment. The angle was much greater than the setting angle of actual duct of the combines studied, which were $48{\sim}56^{\circ}$. By comparison of these results, it was suggested to change duct setting angle so as to reduce the frictional force, between the duct wall and tailings, by reducing the difference between the ejecting and setting angles. 2. The velocity of the air stream in the duct was in general higher in the upper bound of the duct compared to the lower and decreased as the stream went toward the end of duct. The comparison of the tailings units among the combines studied showed a superior performance with the tapered duct having small diameter in the outlet and with greater number of thrower blade.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.11
• /
• pp.2920-2939
• /
• 2012

Enterprises that develop online games have to deploy supporting infrastructures, including hardware and bandwidth resources, in order to provide a good service to users. First Person Shooter games generate high rates of small UDP packets from the client to the server, so the overhead is significant. This work analyzes a method that saves bandwidth, by the addition of a local agent which queues packets, compresses headers and uses a tunnel to send a number of packets within a multiplexed packet. The behavior of the system has been studied, showing that significant bandwidth savings can be achieved. For certain titles, up to 38% of the bandwidth can be saved for IPv4. This percentage increases to 54% for IPv6, as this protocol has a bigger overhead. The cost of these bandwidth savings is the addition of a new delay, which has an upper bound that can be modified. So there is a tradeoff: the greater the added delays, the greater the bandwidth savings. Significant reductions in the amounts of packets per second generated can also be obtained. Tests have been deployed in an emulated scenario matching an access network, showing that if the number of players is big enough, the added delays can be acceptable in terms of user experience.

• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.265-275
• /
• 1993

A vapor explosion has been a concern in nuclear reactor safety due to its potential for a destructive mechanical energy release. In order to properly assess the hazard of a vapor explosion, it is necessary to accurately estimate the conversion efficiency of the thermal energy to mechanical energy. In the absence of a complete model to determine the explosive energy yield, one may have to rely on a simpler upper bound estimate such as a thermodynamic model. This paper discusses various thermodynamic models and presents a clarification of each model in their mathematical formulation and the thermodynamic work conversion. It is shown that the work release in the shock adiabatic model of Board and Hall is essentially equal to that of Hicks-Menzies thermodynamic model. The effect of coolant void fraction on the explosion efficiency is also predicted based on these thermodynamic models. Finally, the Hicks-Menzies model is modified to account for the chemical reaction between a metallic fuel and water and the resultant effects on the explosion expansion work are discussed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.1-7
• /
• 2009

When constructing various mobile networks including sensor networks, the problem of finding the layout or graph to interconnect the terminals or nodes of the network may come up. Providing a common scheme that can be applied to the kind of problems, and formulating the bounds of the run time and the result of the algorithm from the scheme, one may evaluate precisely the plan of constructing analogous network systems. This paper, dealing with EMST(Euclidean Minimum Spanning Tree) that represents such problems, provides the scheme for constructing EMST by parallel processing over distributed environments, and the ground for determining the maximum difference of the layout or the graph produced from the scheme: the difference from EMST. In addition, it provides the upper bound of the run time of the algorithm from the scheme.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.8
• /
• pp.77-83
• /
• 2012

In this paper, when interference caused by the primary user exists, the capacity performance of the mean value-based power allocation scheme is analyzed and evaluated under the outdated channel environment in spectrum sharing systems. When interference due to the primary transmitter affects the secondary receiver, we derive the upper bound of the ergodic capacity of the mean value-based power allocation scheme in a closed form. Furthermore, based on that, we investigate how interference due to the primary transmitter degrades the ergodic capacity of the secondary user. In simulation results, we show the performance degradation of the secondary user due to interference caused by the primary user. In addition, we show that the region where the mean value-based power allocation scheme outperforms the outdated channel information-based power allocation scheme is reduced as interference by the primary user increases.

• Computational Structural Engineering
• /
• v.1 no.2
• /
• pp.101-109
• /
• 1988

The evaluation of the system reliability is generally quite difficult and costly as the structure becomes large and complex, especially when it is subjected to multiple time varying loads, and for redundant structures which have many possible modes of failur, e.g., system collapse through the formation of plastic hinge mechanisms. In reality most loadings acting on the structures are random in intensity as well as in occurrence time and duration. To include the load variability in time, the loads are described in terms of stochastic processes. Based on a tri-modal upper bound, a point estimate for the system reliability has been developed for more accuracy without extensive computational effort. This tri-modal point estimate also ensures the continuity of the system reliability function, which is a necessary condition in many nonlinear programming techniques. In addition, the Load Coincidence method, by which the combined effect of time varying loads are taken into account, has been modified to suitable for cases with an always-on load.